COOLMOON AR-1

Contents

COOLMOON AR-1 RGB Mini Controller Instruction Manual

Model: AR-1

1. Introduction

The COOLMOON AR-1 RGB Mini Controller is designed to manage the lighting of 5V 3-pin ARGB (Addressable RGB) components in your computer system. This controller offers a compact design with an individual technological appearance, creating dynamic lighting effects. It features broad compatibility with various standard 5V 3-pin ARGB light-emitting products available on the market. The interface cable and power supply cable are designed with sufficient length to meet the requirements of most PC chassis configurations.

COOLMOON AR-1 ARGB Mini Controller with lengthened interface cable and SATA power supply.

Figure 1: COOLMOON AR-1 ARGB Mini Controller Overview

2. Safety Information

  • Always disconnect power from your computer system before installing or removing any components.
  • Caution: Avoid connecting or disconnecting wires while the power is on to prevent damage to the controller or connected devices.
  • Ensure proper connection of all cables to avoid short circuits or electrical hazards.
  • Keep the controller away from moisture and extreme temperatures.
  • This device is intended for use with 5V 3-pin ARGB products only. Do not connect to 12V RGB headers.

3. Package Contents

The package includes the following item:

  • 1 x COOLMOON AR-1 RGB Mini Controller
Package contents showing one COOLMOON AR-1 ARGB mini controller.

Figure 2: Included Controller

4. Specifications

AttributeValue
Product NameARGB Mini Controller
BrandCOOLMOON
Model NumberAR-1
ColorBlack
Interface TypeSATA, 5V 3-Pin ARGB
3-Pin Cable Length160 ± 10 mm
SATA Power Cable Length500 ± 10 mm
Weight21 g
Dimensions (L x W x H)46 x 22 x 9.5 mm (1.81 x 0.87 x 0.37 in)
TypeFlexible Flat Cable
OriginMainland China
Dimensions of the COOLMOON AR-1 controller: 46mm length, 22mm width, 9.5mm height.

Figure 3: Controller Dimensions

5. Setup and Installation

Follow these steps to properly install your COOLMOON AR-1 RGB Mini Controller:

  1. Ensure your computer is completely powered off and unplugged from the wall outlet before beginning installation.
  2. Locate an available SATA power connector from your power supply unit (PSU).
  3. Connect the SATA power cable of the AR-1 controller to the available SATA power connector from your PSU.
  4. Connect the 5V 3-pin ARGB interface cable from your ARGB lighting components (e.g., cooling fans, light strips, RAM heatsinks) to the 5V 3-pin input on the AR-1 controller. Ensure the arrow on the connector aligns with the +5V pin on the controller.
  5. If connecting multiple ARGB devices, you can daisy-chain them to the controller's 5V 3-pin output, provided they are compatible.
  6. Once all connections are secure, you can power on your computer.

Video 1: Demonstration of connecting the AR-1 controller to a fan and light strips.

Diagram showing cable lengths: 3-pin interface line 160±10mm, power supply line 500±10mm.

Figure 4: Cable Lengths and Connections

6. Operating Instructions

The COOLMOON AR-1 controller features three buttons for easy operation:

Detailed view of the M, S, C buttons on the COOLMOON AR-1 controller.

Figure 5: Controller Buttons (M, S, C)

  • M Key (Mode):
    • Single click to switch to the next light mode. The controller cycles through its built-in light modes.
  • S Key (Speed/On/Off):
    • Single click to switch the light change speed. There are 8 adjustable speed gears.
    • Press and hold the S key for 4 seconds to turn off the lighting.
    • Press and hold the S key again for 4 seconds to turn on the lighting.
  • C Key (Color/Brightness):
    • Single click to switch to other light colors within the same lighting style or to reverse the light direction.
    • Press and hold the C key for 5 seconds to switch the brightness of the light. There are 6 levels of brightness that can be decreased and cycled through.

The controller has over ten built-in light modes. The controller's lighting effects will remain synchronized across all connected ARGB devices.

7. Maintenance

  • Keep the controller clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the controller to liquids or corrosive substances.
  • Do not attempt to disassemble the controller, as this may void any potential warranty and could cause damage.

8. Troubleshooting

  • No lighting or incorrect lighting:
    • Ensure the SATA power cable is securely connected to your PSU.
    • Verify that the 5V 3-pin ARGB connectors are correctly aligned and fully inserted. The arrow on the connector should match the +5V pin.
    • Confirm that your ARGB devices are 5V 3-pin compatible. This controller is not compatible with 12V RGB headers.
    • Check if the lighting has been turned off by long-pressing the 'S' key. Long-press 'S' again for 4 seconds to turn it back on.
  • Controller not responding:
    • Ensure the controller is receiving power via the SATA connection.
    • Disconnect and reconnect all cables, ensuring they are firmly seated.
  • Fan not spinning (if connected to controller):
    • This controller is designed for ARGB lighting control only. If your fan is not spinning, it is likely because it is only connected to the 5V 3-pin light interface and not to a separate fan speed (PWM) interface. Fans require a separate connection to the motherboard or a dedicated fan controller for speed control.
  • Lighting not synchronizing with motherboard software:
    • This controller operates independently and does not support synchronization with motherboard ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light). It uses its own built-in lighting modes.

9. User Tips

  • The AR-1 controller is ideal for systems without a 5V 3-pin ARGB header on the motherboard, allowing you to still enjoy addressable RGB lighting.
  • You can connect multiple ARGB devices in series (daisy-chaining) to the controller without issues, as demonstrated in the product video. This allows for expanding your lighting setup.
  • Remember that this controller manages lighting effects only. For fan speed control, ensure your fans are connected to appropriate fan headers on your motherboard or a separate fan controller.

10. Warranty and Support

For warranty information or technical support, please refer to the retailer or manufacturer's official website. Keep your proof of purchase for any warranty claims.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.