VLAND LED Tail Lights Instruction Manual

1. Introduction

Thank you for choosing VLAND LED Tail Lights. This manual provides detailed instructions for the installation, operation, and maintenance of your new tail light assembly. These premium LED tail lights are designed to refresh your vehicle's appearance with a visually striking presence, featuring Dynamic Running Lights (DRL), Dynamic Turn Signals, Reverse Lights, and Brake Lights. They meet DOT/SAE standards for photometric and safety compliance and are engineered for easy, direct bolt-on OE fitment or replacement for the stock unit.

Compatibility: Specifically designed for Mitsubishi Lancer 10 EVO X models from 2008 to 2020.

Figure 1: VLAND LED Tail Lights installed on a Mitsubishi Lancer.

2. Setup and Installation

These tail lights are designed for plug-and-play operation, offering direct bolt-on OE fitment or replacement for your vehicle's stock unit. Professional installation is recommended for optimal performance and safety.

2.1. Pre-Installation Check

• Ensure the vehicle's ignition is off and the battery is disconnected before starting installation.
• Inspect the new tail light assemblies for any damage.
• Familiarize yourself with the vehicle's existing tail light wiring and mounting points.

2.2. Installation Steps (General Guide)

1. Access the Tail Light Assembly: Open the trunk and locate the access panels or bolts securing the existing tail light assembly. Remove any trim panels or covers as necessary.
2. Disconnect Wiring: Carefully disconnect the electrical connectors from the back of the old tail light assembly.
3. Remove Old Assembly: Unscrew or unbolt the existing tail light assembly from the vehicle body. Gently pull the assembly away from the vehicle.
4. Prepare New Assembly: If necessary, transfer any bulbs or components from the old assembly to the new one, following the wiring diagram provided.
5. Connect New Wiring: Connect the electrical connectors of the new VLAND LED Tail Lights to the vehicle's wiring harness. Ensure a secure connection.
6. Mount New Assembly: Position the new tail light assembly into the vehicle's opening. Secure it with the original screws or bolts. Do not overtighten.
7. Test Functionality: Reconnect the vehicle's battery. Test all light functions: Running Lights, Brake Lights, Turn Signals (left and right), and Reverse Lights.
8. Final Assembly: Once all functions are confirmed, replace any removed trim panels or covers.

Figure 2: Wiring diagram for VLAND LED Tail Lights.

• RUNNING LIGHT/BRAKE LIGHT SOCKET
• REVERSE LIGHT SOCKET
• TURN SIGNAL SOCKET
• PLUG FOR RUNNING LIGHT/BRAKE LIGHT

Figure 3: Before and After installation comparison.

3. Operating Instructions

The VLAND LED Tail Lights integrate multiple lighting functions for enhanced visibility and modern aesthetics:

• Running Lights (DRL): These illuminate when your vehicle's headlights are on, providing a distinct and modern look.
• Brake Lights: Brightly illuminate when the brake pedal is pressed, signaling deceleration to following vehicles.
• Dynamic Turn Signals: Provide a sequential amber light pattern, clearly indicating your intended turns or lane changes.
• Reverse Lights: Activate when the vehicle is put into reverse, providing illumination for backing up and signaling to others.

Figure 4: Day and Night illumination comparison.

Figure 5: Detailed view of light functions.

4. Maintenance

To ensure the longevity and optimal performance of your VLAND LED Tail Lights, follow these simple maintenance guidelines:

• Cleaning: Clean the outer lens regularly with a soft cloth and mild automotive soap. Avoid abrasive cleaners or harsh chemicals that could damage the lens material.
• Inspection: Periodically check the lights for any signs of condensation, cracks, or loose connections. Address any issues promptly.
• Wiring: Ensure all wiring connections remain secure and free from corrosion.
• LED Longevity: LED lights have a long lifespan and typically do not require bulb replacement. If an LED segment fails, the entire assembly may need to be replaced.

5. Troubleshooting

If you encounter any issues with your VLAND LED Tail Lights, refer to the following troubleshooting tips:

• Lights Not Working:
  • Check all electrical connections to ensure they are securely plugged in.
  • Verify that the vehicle's fuses related to the tail lights are intact and not blown.
  • Ensure the vehicle's battery is properly connected and charged.
• Flickering Lights:
  • Inspect wiring for loose connections or damaged insulation.
  • Ensure proper grounding of the tail light assembly.
• Condensation Inside Lens:
  • Small amounts of condensation can occur due to temperature changes and usually dissipate.
  • If condensation persists or is excessive, check for cracks in the housing or improper sealing. Ensure the vent caps (if present) are clear.
• Turn Signals Not Dynamic/Working Incorrectly:
  • Verify all connections for the turn signal circuit.
  • Ensure the vehicle's flasher relay is functioning correctly (though less common with LED-specific designs).
  • Check for any load resistors if they were part of the installation to prevent hyper-flashing.

If these steps do not resolve the issue, please contact VLAND customer support for further assistance.

6. Specifications

7. User Tips

Currently, there are no specific user tips available from customer reviews or Q&A. We recommend:

• Watching the product video for a clear demonstration of the dynamic turn signal feature.
• Ensuring all connections are watertight after installation to prevent moisture ingress.
• If you are unsure about the installation process, consult a professional automotive technician.

8. Warranty and Support

VLAND provides a 1-Year Warranty for these LED Tail Lights. This warranty covers manufacturing defects and ensures the product meets its stated specifications under normal use.

For warranty claims, technical support, or any questions regarding your VLAND LED Tail Lights, please contact VLAND customer service through your purchase platform or the official VLAND website. Please have your purchase details and product model number (YAB-YS-0155B) ready when contacting support.