BEAR FORCE Wet Sandblaster Lance Nozzle Kit

Contents

Pressure Washer Sandblasting Kit Instruction Manual

Model: Wet Sandblaster Lance Nozzle Kit

1. Introduction

This manual provides detailed instructions for the safe and effective use of your BEAR FORCE Pressure Washer Sandblasting Kit. This kit is designed for wet sandblasting applications, ideal for removing rust, paint, and stubborn dirt from various surfaces. Please read this manual thoroughly before assembly and operation to ensure proper usage and safety.

Safety Warning: Always wear appropriate personal protective equipment (PPE) including eye protection, gloves, and respiratory protection when operating the sandblasting kit. Ensure adequate ventilation and follow all safety guidelines provided with your pressure washer.

2. Package Contents

Verify that all components listed below are present in your package:

  • 1 x Sandblaster (equipped with a top-quality ceramic nozzle)
  • 1 x Stainless Steel Lance (Length: 18 inches / 46 cm)
  • 1 x Transparent Siphon Hose (Length: 3 meters)
  • 12 x Adapters (various types for compatibility with different pressure washer brands)
Overview of the Pressure Washer Sandblasting Kit, showing the sandblaster, lance, siphon hose, and various adapters.

Figure 1: Overview of the Pressure Washer Sandblasting Kit components.

Dimensions of the sandblaster lance (41cm), siphon hose (3m), and abrasive intake tube (26.5cm).

Figure 2: Dimensions of the sandblasting kit components.

3. Specifications

FeatureSpecification
Max Pressure180 bar / 2600 psi
Max Temperature60℃ / 140℉
Lance Length18 inches / 46 cm
Siphon Hose Length3 meters
Body MaterialAlloy
Nozzle MaterialAlloy (with ceramic insert)
Interface MaterialEngineering Plastic
Water Spray TypeFan
With Water PipesYes
Handle TypeFinger Type

4. Setup

4.1. Choosing the Correct Adapter

It is crucial to select the correct adapter for your specific pressure washer gun/wand. Refer to the adapter compatibility list and the detailed dimension diagram below to ensure a proper fit. An incorrect adapter can lead to leaks or damage.

  • Adapter A: For Karcher K-Series pressure washer.
  • Adapter B: For AR Blue Clean, Black Decker (Russia & Europe), Michelin, some Interskol, Greenworks G2~G6, Makita, and most Bosch pressure washers.
  • Adapter C: For Elitech, some Interskol, YILI, some Huter, Patriot, and Daewoo pressure washers.
  • Adapter D: For Nilfisk, STIHL, Gerni, HUSQVARNA, and Greenworks G10~G70 pressure washers.
  • Adapter E: For Lavor, some Hammer, Sterwins, Vax, Champion, Craftsman, and Briggs Stratton pressure washers.
  • Adapter F: For some Huter, Anlu, and Kohler pressure washers.
  • Adapter G: For Nilfisk-Kew and some Karcher HD professional pressure washers.
  • Adapter H: For some Bosch (made before 2013), Portland, Husky, and some Hammer pressure washers.
  • Adapter I: For some Karcher Pro HD/HDS pressure washers (Old trigger gun with standard M22-Male outlet).
  • Adapter J: For some Karcher Pro HD/HDS pressure washers (Easy Force trigger gun).
  • Adapter K: For Kranzle, BOSCH GHP, and water guns with M22-Female thread pressure washers.
  • Adapter L: 1/4 inch quick plug, a popular connector in North America.
Detailed dimensions of all 12 available adapters (A-L) for compatibility reference.

Figure 3: Detailed dimensions of adapters A-L.

4.2. Assembly Instructions

  1. Connect the Adapter: Securely attach the chosen adapter to the end of the stainless steel lance.
  2. Attach to Pressure Washer Gun: Connect the assembled lance (with adapter) to your pressure washer gun. Ensure a tight and leak-free connection.
  3. Connect Siphon Hose: Attach the transparent siphon hose to the designated inlet on the sandblaster unit.
  4. Prepare Abrasive Material: Place the other end of the siphon hose, which has the abrasive intake tube, into a container of dry abrasive material (e.g., silica sand, garnet, crushed glass). Ensure the abrasive material is dry and free of clumps to prevent clogging.
Diagram illustrating the connection of the sandblasting kit to a pressure washer gun and the abrasive material source.

Figure 4: Diagram of the sandblasting kit setup.

Video 1: Product overview and assembly demonstration.

5. Operation

Once the kit is properly assembled and connected to your pressure washer, you can begin the sandblasting process:

  1. Ensure your pressure washer is turned on and operating at the desired pressure (within the kit's maximum limits).
  2. Direct the sandblaster nozzle towards the surface to be cleaned, maintaining a safe distance.
  3. Engage the trigger on your pressure washer gun. Water will flow through the lance, creating a vacuum that draws abrasive material up the siphon hose and mixes it with the high-pressure water stream.
  4. Move the nozzle steadily across the surface to evenly remove rust, paint, or dirt. Adjust your distance and speed as needed for optimal results.
  5. Periodically check the abrasive material level in your container and refill as necessary.
Visual comparison of a surface before and after cleaning with the sandblasting kit.

Figure 5: Example of surface cleaning before and after using the sandblasting kit.

6. Maintenance

Proper maintenance will extend the life of your sandblasting kit:

  • After Each Use: Flush the sandblaster and siphon hose with clean water to remove any remaining abrasive material. This prevents clogging and corrosion.
  • Inspect Nozzle: Regularly check the ceramic nozzle for wear. A worn nozzle can reduce performance and efficiency. Replace if necessary.
  • Check Connections: Ensure all connections (lance to gun, siphon hose to sandblaster) are clean and free of debris.
  • Storage: Store the kit in a dry, clean place, away from extreme temperatures.

7. Troubleshooting

If you encounter issues with your sandblasting kit, refer to the following common problems and solutions:

  • No Abrasive Suction:
    • Ensure the siphon hose is fully submerged in the abrasive material.
    • Check for kinks or blockages in the siphon hose.
    • Verify that the ceramic nozzle is not worn or clogged.
    • Confirm all connections are airtight; air leaks can prevent suction.
  • Poor Cleaning Performance:
    • Check if the pressure washer is operating at sufficient pressure.
    • Ensure the abrasive material is dry and of appropriate grit size for the task.
    • Inspect the ceramic nozzle for wear; a worn nozzle will reduce blasting effectiveness.
  • Leaks at Connections:
    • Tighten all connections securely.
    • Check O-rings and seals for damage or wear and replace if necessary.
    • Ensure the correct adapter is used for your pressure washer gun.

If you are unsure about adapter compatibility, please send a photo of your pressure washer gun/wand to the seller for confirmation.

8. User Tips

  • Abrasive Choice: Different abrasive materials and grit sizes are suitable for various tasks. Experiment with fine sand for delicate surfaces and coarser grits for heavy rust or paint removal.
  • Nozzle Wear: The ceramic nozzle is a wear item. Keep spare nozzles on hand, especially if you use the kit frequently or with very aggressive abrasives.
  • Test Area: Always test the sandblasting kit on an inconspicuous area first to determine the optimal pressure, abrasive type, and distance for your specific application.
  • Ventilation: Always work in a well-ventilated area to prevent inhalation of dust and abrasive particles.

9. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims, technical support, or replacement parts, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.