1. Product Overview
The Akko MONSGEEK MG75W and MG108W are high-performance mechanical keyboards designed for gaming and productivity. Available as a complete keyboard or a DIY kit, these models feature hot-swappable switches, dual-mode connectivity (Wired USB Type-C and Wireless 2.4GHz), and EVA sound dampening for an enhanced typing experience.
Video: Overview of the Akko MONSGEEK keyboard, demonstrating its features, adjustable feet, and typing sound.
Image: Akko MONSGEEK MG75W and MG108W models, highlighting Wireless 2.4G + USB connectivity and EVA Soundproof feature.
2. Setup Guide
2.1 Unboxing and Initial Inspection
Carefully remove the keyboard and all accessories from the packaging. Inspect for any visible damage. The package typically includes the keyboard/DIY kit, a USB Type-C cable, and a 2.4GHz wireless receiver.
2.2 Installing Switches and Keycaps (DIY Kit)
If you have purchased the DIY kit, you will need to install your preferred mechanical switches and keycaps. The keyboard features hot-swappable sockets, allowing for easy installation without soldering.
- Align the pins of the mechanical switch with the holes on the PCB.
- Gently push the switch until it clicks into place. Ensure it is fully seated and straight.
- Repeat for all switches.
- Place the keycaps onto the installed switches, ensuring correct orientation for each key.
Note the PCB orientation: MG108W models are available with both North-facing and South-facing PCBs. This affects keycap compatibility, especially with Cherry profile keycaps, which may interfere with North-facing switches.
Image: MG108W keyboard with North-facing PCB.
Image: MG108W keyboard with South-facing PCB.
2.3 Connecting the Keyboard
The keyboard supports two connection modes:
- Wired Mode (USB Type-C): Connect the provided USB Type-C cable from the keyboard to an available USB port on your computer. The keyboard will be automatically detected.
- Wireless Mode (2.4GHz):
- Locate the 2.4GHz USB receiver, usually stored in a compartment on the keyboard's underside.
- Plug the receiver into an available USB port on your computer.
- Switch the keyboard to 2.4GHz wireless mode using the switch located on the back or bottom of the keyboard.
- The keyboard should automatically connect to the receiver.
2.4 Adjusting Keyboard Angle
The keyboard features adjustable feet on its underside. Flip them out to achieve a more ergonomic typing angle if desired.
3. Operating Instructions
3.1 Basic Keyboard Functions
The Akko MONSGEEK keyboards function as standard QWERTY keyboards. All keys perform their labeled functions. For specific layouts (e.g., MG75W 75% layout or MG108W full-size layout), refer to the key legends for function keys and secondary functions accessed via the 'Fn' key.
Image: MG75W keyboard in Black.
Image: MG75W keyboard in White.
3.2 Switching Between Wired and Wireless Modes
Use the physical switch located on the back or bottom of the keyboard to toggle between wired (USB) and wireless (2.4GHz) modes. Ensure the correct mode is selected for your desired connection type.
3.3 Backlight Control (if applicable)
Some models of the Akko MONSGEEK keyboards may feature backlighting. If your model includes backlighting, refer to the keyboard's specific key combinations (often involving the 'Fn' key) for adjusting brightness, effects, or turning the backlight on/off. Dedicated software may also be available for advanced customization.
3.4 Mac Compatibility
The Akko MONSGEEK keyboards are generally compatible with macOS. Basic keyboard functions should work out-of-the-box. For advanced features or key remapping, you may need to use third-party software or the manufacturer's dedicated software (if available for Mac).
4. Maintenance
4.1 Cleaning the Keyboard
To ensure longevity and optimal performance, regular cleaning is recommended:
- General Cleaning: Use a soft, lint-free cloth to wipe down the keycaps and keyboard frame. For stubborn dirt, slightly dampen the cloth with water or a mild cleaning solution (avoid harsh chemicals).
- Deep Cleaning (Keycaps): For thorough cleaning, keycaps can be removed using a keycap puller. Wash them in warm, soapy water, rinse thoroughly, and ensure they are completely dry before reattaching.
- Dust Removal: Use compressed air to blow away dust and debris from between the keycaps and switches.
4.2 Replacing Switches
Thanks to the hot-swappable design, switches can be easily replaced without soldering:
- Power off the keyboard or disconnect it from your computer.
- Use a switch puller tool to carefully grip the switch and pull it straight up from the PCB.
- Align the pins of the new switch with the holes on the PCB.
- Gently push the new switch until it clicks into place. Ensure it is fully seated and straight to avoid bending pins.
5. Troubleshooting
5.1 Keyboard Not Responding
- Wired Mode: Ensure the USB Type-C cable is securely connected to both the keyboard and the computer. Try a different USB port or cable.
- Wireless Mode:
- Check if the 2.4GHz receiver is properly plugged into a USB port.
- Ensure the keyboard's mode switch is set to 2.4GHz wireless.
- Verify the keyboard has sufficient battery charge.
- Try re-pairing the keyboard with the receiver (refer to manufacturer's specific instructions if available).
- Specific Keys Not Working: If only a few keys are unresponsive, the switches might be faulty or not properly seated. Try removing and re-inserting the affected switches. If the issue persists, replace the switches.
5.2 Backlight Issues
- If the backlight is not working, ensure it is enabled via the keyboard's function keys or software.
- Check if the brightness is set to a visible level.
- Ensure the keyboard is receiving sufficient power (especially in wired mode).
5.3 Connectivity Lag or Disconnections (Wireless)
- Ensure the 2.4GHz receiver is not obstructed and is within close proximity to the keyboard.
- Avoid placing the receiver near other wireless devices or sources of electromagnetic interference (e.g., Wi-Fi routers, large metal objects).
- Check for low battery and recharge the keyboard if necessary.
6. Specifications
| Feature | Description |
|---|---|
| Models | MONSGEEK MG75W, MONSGEEK MG108W |
| Layout | MG75W: 75% (83 keys) MG108W: Full-size (108 keys) |
| Connectivity | Wired (USB Type-C), Wireless (2.4GHz) |
| Switch Type | Hot-swappable Mechanical Switches |
| Sound Dampening | EVA Soundproof Material |
| Application | Desktop, Laptop |
| Backlight | Varies by model/configuration (some models may feature no backlight, others may have adjustable backlighting) |
| PCB Orientation | MG108W available in North-facing and South-facing PCB variants |
| Certifications | CE, WEEE |
7. User Tips
- Software Customization: For advanced customization of key assignments, macros, or backlight settings (if applicable), check the official Akko website for dedicated software compatible with your keyboard model.
- Switch Compatibility: The hot-swap sockets are designed for standard 3-pin or 5-pin mechanical switches (e.g., Cherry MX style, Gateron, Kailh). Optical switches are generally not compatible with these sockets.
- Keycap Compatibility: Be mindful of PCB orientation when choosing keycaps. South-facing PCBs offer better compatibility with Cherry profile keycaps, avoiding interference with switches.
- MG108W North-facing Shift Key: For the MG108W North-facing version, the left Shift key may feature two separate switch sockets. This design allows for flexibility in switch placement or potential customization for specific key functions.
- Aluminum Top Plate: While not explicitly stated for all models, some users inquire about an aluminum top plate, which can contribute to a more premium feel and sound profile. Check product specifics for your exact model.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official Akko website or contact the seller directly. Keep your proof of purchase for any warranty claims.