HXCONTROLLER MPPT Solar Water Pump Controller

Contents

Aluminum Alloy MPPT Solar Water Pump Controller User Manual

Model: MPPT Solar Water Pump Controller

Brand: HXCONTROLLER

1. Introduction

This controller is specifically designed for solar energy applications, featuring an electronically driven DC brushless motor. It boasts high efficiency with Maximum Power Point Tracking (MPPT) functionality, automatically adjusting motor speed based on sunlight intensity. The system automatically starts when sunlight is available and shuts down when there is no sunlight. It is suitable for deep well pumping, agricultural irrigation, and domestic water intake.

Key features include a high-quality aluminum alloy shell for temperature resistance, an LED display for viewing power, current, voltage, and speed, and robust wiring ports with high insulation voltage, resistant to vibration.

A notable feature is the automatic pump stop when water is absent, eliminating the need for a liquid level switch in the well (a liquid level switch is required for water towers).

HXCONTROLLER MPPT Solar Water Pump Controller
Figure 1.1: HXCONTROLLER MPPT Solar Water Pump Controller
Video 1.1: Demonstration of the solar water pump system in operation.

2. Specifications

AttributeValue
Product NamePhotovoltaic water pump controller/solar water pump controller
MaterialAluminum Alloy
ApplicationCharger Controller, Voltage Controller
Working FluidWater
Drive ModeDC Brushless
Transmission MediumWater pump
Rated Voltage Options24V, 48V, 72V, 96V, 110V
Maximum Current16A
CertificationCE
Is Smart DeviceNo
is_customizedYes
Weight1.8kg

2.1. Performance Parameters by Model

ModelDC 24V 48VDC 72VDC 96-110V
Rate Voltage24V - 48V72V96-110V
Rated Input Power (W)450W (24V), 900W (48V)1400W1800W (96V), 2000W (110V)
Max Input Current (A)16A16A16A
Max Input Voltage (V)63V (24V), 100V (48V)150V200V
Min Input Voltage (V)20V (24V), 30V (48V)50V60V
MPPT Voltage (V)24V-36V (24V), 48V-72V (48V)72V-108V96V-144V
Working Condition (°C)-15 to 60 degrees-15 to 60 degrees-15 to 60 degrees

Important: Users must use an instrument to measure the open circuit voltage of the solar panel before starting, or use knowledge of series and parallel connections to calculate it. The open circuit voltage of the solar panel must not exceed the maximum input voltage of the controller, otherwise it will cause irreversible damage.

Dimensions of the HXCONTROLLER MPPT Solar Water Pump Controller
Figure 2.1: Controller Dimensions

3. Setup and Installation

3.1. Solar Panel Connection Information

Solar panels can be connected in series, parallel, or a combination of both to achieve the desired voltage and current for the pump controller.

  • Series Connection: When panels are connected in series, the voltage adds up, while the current remains unchanged.
  • Parallel Connection: When panels are connected in parallel, the current adds up, while the voltage remains unchanged.
Diagram showing solar panels connected in series, parallel, and series-parallel configurations.
Figure 3.1: Solar Panel Connection Configurations (Series, Parallel, Series-Parallel)

3.2. Wiring Diagram

The controller features clearly labeled connection terminals for solar panels, pump motor, and water level sensors. Ensure all connections are secure and correctly polarized.

Detailed view of the controller's connection terminals and system wiring diagram.
Figure 3.2: Connection Terminal Description and System Wiring Diagram

Warning: Do not reverse the positive and negative of the power connection, otherwise the system will not work.

3.3. Pre-Installation Inspection

  1. Before use, check whether the electric pump is intact, and inspect for any looseness, seepage, oil leakage at each connection, or accidental damage (e.g., to the cable line).
  2. Use a megohmmeter to measure the insulation resistance of the pump; it should be greater than 2MΩ.
  3. If the cable supplied with the pump is not long enough and needs extension, the diameter of the added wire must be larger than the original one. All joints must be well sealed with waterproof tape.
  4. Before formal use, connect the pump to the power supply and perform a startup check. The pump must always be submerged in water when running (dry running is strictly forbidden). If the pump runs incorrectly (no water flowing out), reconnect any two of the power cables.
  5. When installing the pump, use ropes at the hole ring for lifting. Do not lift the pump by its cable.
  6. The pump should be installed at least 1 meter from the bottom to prevent mud and sand from being sucked in, which could damage the mechanical seal and impeller.

4. Operation

4.1. Operation Panel Overview

Front view of the controller showing the LED display and control buttons.
Figure 4.1: Controller Operation Panel

4.1.1. LED Indicators

  • "V" light: Indicates the screen is displaying "input voltage".
  • "RPM" light: Indicates the screen is displaying "motor speed".
  • "A" light: Indicates the screen is displaying "input current".
  • "W" light: Indicates the screen is displaying "input power".
  • "Tank" light: Illuminates when the tank is full.
  • "Well" light: Illuminates when there is no water in the water source.
  • "MPPT" light: Illuminates when there is solar input power.
  • "Power" light: On when the pump is running, flashing when the pump stops.

4.1.2. Key Operations

ButtonFunction
SetManufacturer operating only.
EnterManufacturer operating only.
Up (▲)Rotation speed setting: each press increases speed by one gear. In fault state, ON/OFF the fault display.
Down (▼)Rotation speed setting: each press decreases speed by one gear.
SwitchIn running status, switches display mode (Voltage (V) -> Speed (RPM) -> Current (A) -> Power (W) cyclically).
ON/OFFStarts/stops the pump.

4.2. Pump Operation Modes

The pump detects the power supply mode (DC battery or PV solar) each time it starts. The detection time is 10 seconds. During this process, setting speed is invalid.

4.2.1. Starting the Pump

  • Power-on Start: When the system is powered on, the pump will start immediately without detecting a tank shortage signal (no shutdown conditions).
  • Start via Key: If the system is off (digital tube displays OFF), press the ON/OFF key to switch to the ON state. The pump will start immediately without detecting a tank shortage signal.
  • Start when Water Tank is Low: If the system is on but the pump is off, and the water tank shortage switch is closed (TL signal terminal and COM terminal are short-circuited), the pump will start immediately.

4.2.2. Stopping the Pump

  • Shutdown by Float Signal (Tank Full): If the pump is running and the water tank becomes full (TH signal terminal COM are short-circuited, TANK light on), the pump will stop immediately and restart in 20 minutes.
  • Shutdown by Float Signal (Well Dry): If the pump is running and there is a water shortage in the well (WEL signal terminal and COM are short-circuited, WELL light on), the pump will stop immediately and restart in 15 minutes.
  • Shutdown by Dry Pumping: If the pump runs for some time with current power less than the set power at the current speed for 20 seconds, it will stop immediately (error P48). Automatic recovery after 30 minutes.
  • Shutdown by Pressing Key: When the pump is running, press the ON/OFF key to stop the pump.

4.2.3. Pump Running Modes (DC/PV)

  • DC (Battery) Mode:
    • Speed is adjustable from 1000-6000 RPM. Default is 6000 RPM. Use Up/Down keys to adjust.
    • To prevent battery over-discharge, the pump will stop if the voltage drops below the corresponding protection voltage (e.g., 20V for 24V system, 40V for 48V system, etc.).
  • PV (Solar) Mode:
    • Speed setting is similar to DC mode, with a 6000 RPM maximum limit.
    • The running speed is determined by the current solar panel power. The system tracks the Maximum Power Point (MPPT) in real-time.
    • As sunlight intensity increases, the output power of the solar panel increases, and the pump speed increases (and vice versa).
    • The MPPT indicator flashes; faster flashing indicates closer to maximum operating point.
    • If solar power is insufficient, the pump speed will decrease. If speed drops to 600 RPM, the pump will stop (error P46) after 3 seconds.
    • If solar power is insufficient to maintain starting or running, the output voltage of the solar panel will drop rapidly. If it drops to the minimum voltage for 10 seconds, error "PL" will occur. The pump will attempt to start 5 times; if it fails, it will restart after 30 minutes.

4.3. Anti-Reverse Function

If the P+ and P- terminals are connected in reverse, the controller will continuously alarm.

5. Maintenance

  1. After 3000 hours of operation, the wearing parts (bearings, sealing rings, mechanical seals, etc.) must be replaced to prevent greater damage.
  2. If the pump will not be used for an extended period, it should be cleaned, wiped dry, and stored in a ventilated, dry place.

6. Troubleshooting

Error CodeErrorPossible CausesRecovery
P0Hardware overcurrent
  • Controller and pump mismatch.
  • Short circuit in U, V, W 3-phase wiring.
Automatic recovery after 60s.
P43Phase protectionShort circuit in U, V, W 3-phase wiring.Automatic recovery after 60s.
P46Low Speed protection
  • Controller and pump mismatch.
  • Extension cable too long (use thicker one).
  • Input power too low (increase input power).
  • Motor blocked (clean pump).
Automatic recovery after 30s.
P48Running dry
  • Air in pump (cut power, reconnect after 30s).
  • No water in source (restart when water is available).
Automatic recovery after 30s or restart.
P49Software overcurrent
  • Controller and pump mismatch.
  • Short circuit in U, V, W 3-phase wiring.
Automatic recovery after 30s.
P50Low powerInput voltage too low (refer to electrical characteristics for correct distribution).Automatic recovery after 5s when input voltage resumes.
P51Over powerInput voltage too high (refer to electrical characteristics for correct distribution).Automatic recovery after 5s when input voltage resumes.
P60High TemperatureMCU temperature in controller over 90°C.Automatic recovery after 5s.
E8Current sampling failureSwitch off power, restart after 30s.Recovery when restart.
PLLow input power
  • No sunshine (restart when enough sunshine).
  • Solar panels unsuitable (select suitable solar panel).
Automatic recovery after 30s (first 5 times), then after 30mins.
Continuous rumblingInput wire is reversedReconnect P+ and P-.Recovery when restart.

7. User Tips

  • Ensure your water pump's magnetic steel is compatible (3 pairs of poles) for normal operation with this controller. If unsure, consult customer service with your pump's parameters.
  • Always verify the open circuit voltage of your solar panels before connecting to avoid damage to the controller.
  • For optimal performance, ensure proper sizing and connection of solar panels (series/parallel) to match the controller's voltage and power requirements.

8. Frequently Asked Questions (FAQ)

Q: In what scenarios can I use this controller?
A: You can use it in various solar water pump applications, including deep well pumping, agricultural irrigation, and domestic water intake.
Q: What are the functions of this controller?
A: It can function as a charger controller and a voltage controller.
Q: Which category does this controller belong to?
A: It belongs to the solar water pump control category.
Q: Can you tell me more about its highlights?
A: Some of its highlights include CE certification and customization options.
Q: What are the benefits of using this controller?
A: Using this controller ensures efficient charging and effective voltage control for your solar water pump system.
Q: What is the voltage of it?
A: The voltage can be 24V, 48V, 72V, or 96V.
Q: How to check if my water pump can be used with this controller?
A: Please check the magnetic steel of your water pump. If it has 3 pairs of poles, the controller can be used normally. If you are unsure, please send the parameters of your water pump to customer service for confirmation.

9. Warranty and Support

For any issues not covered in this manual or for further assistance, please contact HXCONTROLLER Official Store customer support. Refer to the official product page for warranty details and contact information.

A PDF version of the user manual is available for download: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.