FGHGF V55 Pro Virtual Wall

Contents

FGHGF Virtual Wall for ILIFE V55 Pro Robot Vacuum Cleaner

Model: V55 Pro Virtual Wall

Brand: FGHGF

1. Introduction

The FGHGF Virtual Wall is an accessory designed to work with your ILIFE V55 Pro robot vacuum cleaner. It creates an invisible barrier that the robot vacuum will not cross, allowing you to restrict the robot's cleaning area to specific rooms or sections of your home. This manual provides instructions for proper setup, operation, and maintenance of your virtual wall.

2. Product Overview

2.1 Package Contents

  • 1 x FGHGF Virtual Wall

2.2 Key Features

  • Creates an invisible barrier for your robot vacuum.
  • Two selectable modes for different barrier strengths/ranges.
  • Compact and portable design.
  • Constructed from durable Metal and ABS Plastic.

2.3 Product Diagram

Front view of the FGHGF Virtual Wall showing the power switch and mode selector.
Figure 1: Front view of the Virtual Wall with controls.
Bottom view of the FGHGF Virtual Wall, indicating the battery compartment.
Figure 2: Bottom view of the Virtual Wall, showing the battery compartment.

3. Compatibility

This FGHGF Virtual Wall is specifically designed for use with the ILIFE V55 Pro robot vacuum cleaner. Please note: It is NOT compatible with the ILIFE V55 robot cleaner (non-Pro model). Ensure your robot vacuum is the 'V55 Pro' model for proper functionality.

4. Setup

4.1 Battery Installation

  1. Locate the battery compartment on the bottom of the virtual wall (refer to Figure 2).
  2. Open the battery compartment cover.
  3. Insert the required batteries (typically 2x AA batteries, not included) according to the polarity markings (+/-).
  4. Close the battery compartment cover securely.

4.2 Placement

Place the virtual wall on a flat surface in the area where you want to create a barrier. Ensure the front of the virtual wall (where the switches are located) faces the area you want to block off. For best results:

  • Place it near doorways or entrances to rooms you want the robot to avoid.
  • Do not place it behind large metal objects, as this may interfere with the signal.
  • Keep it away from direct sunlight or strong light sources that might affect its sensors.

5. Operating Instructions

5.1 Powering On/Off

To turn on the virtual wall, slide the power switch (usually labeled 'ON/OFF') to the 'ON' position. To turn it off, slide the switch to 'OFF'. It is recommended to turn off the virtual wall when not in use to conserve battery life.

5.2 Mode Selection

The virtual wall features a mode selector switch (often labeled '1V/2V' or 'I/II'). This switch allows you to adjust the strength or range of the invisible barrier:

  • Mode 1 (e.g., '1V' or 'I'): Provides a shorter or less intense barrier, suitable for smaller openings or subtle boundary creation.
  • Mode 2 (e.g., '2V' or 'II'): Provides a longer or more intense barrier, ideal for wider doorways or ensuring the robot stays out of a larger area.

Experiment with both modes to find the optimal setting for your specific needs and environment.

5.3 Using with Your Robot Vacuum

Once the virtual wall is powered on and placed, activate your ILIFE V55 Pro robot vacuum. The robot will detect the invisible barrier emitted by the virtual wall and automatically avoid crossing it, effectively cleaning only within the designated area.

6. Maintenance

6.1 Cleaning

Wipe the exterior of the virtual wall with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the surface.

6.2 Battery Replacement

When the virtual wall's indicator light dims or the robot vacuum starts crossing the barrier, it's time to replace the batteries. Follow the battery installation steps in Section 4.1 to replace them with fresh batteries.

7. Troubleshooting

7.1 Robot Crosses the Barrier

  • Check Batteries: Ensure the batteries are fresh and correctly installed.
  • Check Power: Make sure the virtual wall is switched 'ON'.
  • Check Mode: Try switching to the higher intensity mode (e.g., '2V' or 'II').
  • Reposition: Adjust the placement of the virtual wall to ensure it has a clear line of sight to the area you want to block.
  • Interference: Move the virtual wall away from other electronic devices that might cause interference.

7.2 Virtual Wall Does Not Turn On

  • Check Batteries: Verify that the batteries are new and inserted with correct polarity.
  • Battery Compartment: Ensure the battery compartment cover is closed properly.

8. Specifications

FeatureSpecification
Model NumberV55 Pro Virtual Wall
CompatibilityILIFE V55 Pro Robot Vacuum Cleaner
MaterialMetal, ABS Plastic
Dimensions (L x W x H)15 cm x 12 cm x 8 cm (approx.)
Weight0.2 kg (approx.)
Power SourceBattery-operated (batteries not included)
ModesTwo selectable barrier modes

9. User Tips

No specific user tips were available from customer reviews or Q&A for this product. However, general tips for virtual walls include:

  • Strategic Placement: Experiment with different placements to find the most effective barrier for your home layout.
  • Battery Life: Turn off the virtual wall when your robot vacuum is not in use to extend battery life.
  • Clear Path: Ensure there are no obstacles directly in front of the virtual wall that could block its signal.

10. Warranty and Support

For warranty information or technical support, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.