Kllisre DDR4 DIMM Desktop Memory

Contents

Kllisre DDR4 Desktop Memory User Manual

Model: DDR4 DIMM Desktop Memory

Brand: Kllisre

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Kllisre DDR4 Desktop Memory module(s). Kllisre memory is designed to enhance computer performance for general users, gamers, and computer enthusiasts alike, offering high stability and superior quality.

For additional guidance, a user manual in PDF format is available: Kllisre DDR4 Memory User Manual (PDF)

2. Specifications

Feature Specification
Brand Kllisre
Interface Type 288 Pin Unbuffered DIMM Non ECC
Frequency Options 2400 MHz, 2666 MHz, 3200 MHz
Type DDR4
Memory Voltage 1.2V
Application Desktop
Cooling Fin Yes
RGB No
High-concerned chemical None
CAS Latency (CL) 2400MHz = CL17, 2666MHz = CL19, 3200MHz = CL22
Original Chips For HY SEC MIC...
Package Yes

Available Capacities:

  • 4GB (2400MHz, 2666MHz)
  • 8GB (2400MHz, 2666MHz, 3200MHz)
  • 16GB (2666MHz, 3200MHz)

3. Installation Guide

Warning: Always handle memory modules by the edges. Avoid touching the gold contacts or components on the circuit board. Static electricity can damage the memory, so use an anti-static wrist strap when handling components.

3.1. Power Down the System

Shut down the computer completely and disconnect all power cables from the power supply.

3.2. Open the Computer Case

Remove the side panel of your computer case to access the motherboard.

Internal view of a desktop computer case with components, showing space for RAM installation.

Image: Internal view of a desktop computer case, illustrating the area where RAM modules are installed.

3.3. Locate Memory Slots

Identify the memory slots on your motherboard. Consult your motherboard manual for optimal slot population order (usually slots 2 and 4 for dual channel).

Close-up of a motherboard with RAM slots highlighted, indicating where to install memory modules.

Image: Close-up of a motherboard, showing the RAM slots.

3.4. Release Retention Clips

Open the retention clips at both ends of the memory slot by pushing them outward.

Diagram showing how to open RAM slot retention clips by pushing them outwards.

Image: Illustration of opening the retention clips on a RAM slot.

3.5. Align the Memory Module

Align the notch in the memory module with the key in the memory slot to ensure proper orientation. The module should only fit one way.

Diagram showing correct alignment of a DDR4 memory module with the motherboard slot notch.

Image: Diagram illustrating the correct alignment of the memory module with the slot's key.

3.6. Install the Memory

Firmly press down on the memory module until the retention clips snap into place automatically, securing the module.

Diagram showing a DDR4 memory module being pressed into the slot until clips engage.

Image: Illustration of pressing the memory module into the slot until it clicks.

3.7. Repeat for Additional Modules

If installing multiple modules, repeat the process for each module, following the motherboard's recommended population sequence for optimal performance (e.g., dual channel configuration).

Two Kllisre DDR4 memory modules shown side-by-side, ready for installation.

Image: Two Kllisre DDR4 memory modules.

3.8. Close the System

Replace the computer case panel, reconnect all cables, and power on the system.

3.9. Post-Installation Check (BIOS/UEFI)

After installing new memory, enter the system BIOS/UEFI to verify that all memory is detected. To achieve the advertised speed, you may need to enable XMP (Extreme Memory Profile) or D.O.C.P. (Direct Overclock Profile) in your motherboard's BIOS/UEFI settings.

4. Operating Instructions

Once installed and recognized by the system BIOS/UEFI, the Kllisre DDR4 memory modules operate automatically. The operating system will utilize the installed RAM as needed for applications and processes. No further user interaction is typically required for basic operation.

Computer screen displaying Windows Task Manager with memory usage statistics, confirming RAM detection.

Image: A computer screen showing memory usage in Task Manager, confirming successful detection.

5. Maintenance

Kllisre DDR4 memory modules are designed for long-term, maintenance-free operation. However, to ensure optimal performance and longevity of your computer system, consider the following:

  • Dust Removal: Periodically clean the interior of your computer case to prevent dust buildup on components, including memory modules and their slots. Use compressed air for this purpose.
  • Temperature Control: Ensure adequate airflow within your computer case to maintain optimal operating temperatures for all components.
  • Physical Handling: Avoid unnecessary removal or re-installation of memory modules to minimize the risk of physical damage or static discharge.

6. Troubleshooting

Common Issues and Solutions:

  • System Does Not Boot / No Display:
    • Ensure memory modules are fully seated in their slots. Re-seat them firmly until the clips snap into place.
    • Verify that the modules are installed in the correct slots according to your motherboard manual for single or dual-channel configurations.
    • Test modules individually if you have multiple, to identify a potentially faulty stick.
  • Memory Not Detected / Incorrect Capacity Shown:
    • Check BIOS/UEFI settings to confirm the motherboard recognizes the installed RAM.
    • Update your motherboard's BIOS/UEFI to the latest version, as this can improve memory compatibility.
    • Ensure XMP/D.O.C.P. is enabled in BIOS/UEFI to achieve advertised speeds, if applicable.
  • System Instability / Blue Screens of Death (BSOD):
    • Run a memory diagnostic tool (e.g., Windows Memory Diagnostic or MemTest86) to check for errors.
    • If overclocking (including XMP/D.O.C.P.), try resetting BIOS settings to default or manually setting memory timings and voltage.
    • Ensure your power supply is sufficient for all system components.
  • Incompatibility with Motherboard/CPU:
    • While Kllisre memory is designed for broad compatibility, some specific motherboard/CPU combinations might have limitations. Consult your motherboard's Qualified Vendor List (QVL) for tested compatible memory.

7. User Tips

  • XMP/D.O.C.P. Activation: Many users recommend enabling XMP (Extreme Memory Profile) or D.O.C.P. in the BIOS/UEFI settings after installation to ensure the memory operates at its advertised speed (e.g., 3200MHz). Without this, it might default to a lower speed like 2133MHz or 2400MHz.
  • Compatibility Check: Before purchasing, especially for older or less common motherboards (like some X99 or Xeon boards), verify compatibility. While many users report success with X99 platforms and Ryzen CPUs, checking your motherboard's QVL is always a good practice.
  • Dual Channel Configuration: For optimal performance, install memory modules in pairs into the correct dual-channel slots as specified by your motherboard manual.
  • Packaging Inspection: Upon arrival, inspect the packaging and the memory module itself for any physical damage. Although rare, damaged packaging can sometimes indicate issues.

8. Frequently Asked Questions (FAQ)

Q: Does this memory work with X99 motherboards?

A: Yes, many users have reported successful operation with X99 motherboards, including those with Xeon processors. However, always refer to your specific motherboard's manual for optimal slot population and compatibility.

Q: Is this memory compatible with AMD Ryzen CPUs and motherboards (e.g., AM4 socket, A520M)?

A: Yes, Kllisre DDR4 memory is generally compatible with AMD Ryzen platforms. Users have confirmed compatibility with Ryzen 5 5600GT, Ryzen 5500, and A520M motherboards. For specific models, checking your motherboard's QVL is recommended.

Q: Is this memory ECC (Error-Correcting Code)?

A: No, the specifications indicate "Unbuffered DIMM Non ECC." This memory is designed for consumer desktop systems, not server-grade applications requiring ECC memory.

Q: Does the 16GB option come as a single stick or two 8GB sticks?

A: The product description typically refers to a single module. If you need a pair (e.g., 2x8GB for 16GB total), you would generally purchase two individual 8GB modules. Always check the specific product variant you are ordering.

Q: What is the CAS Latency (CL) for different frequencies?

A: The CAS Latency varies by frequency: 2400MHz = CL17, 2666MHz = CL19, 3200MHz = CL22.

9. Warranty and Support

Kllisre DDR4 Desktop Memory modules come with a Three Years Warranty. For warranty claims or technical support, please contact your retailer or the official Kllisre support channels.

Products that are not damaged in appearance but are defective due to process or materials will receive a free replacement service. This warranty does not cover defects caused by natural disasters, human factors, or improper operation.

Warranty is void if the warranty label is removed or tampered with.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.