1. Introduction
The COOSPO H6 Heart Rate Monitor captures real-time heart rate data using both Bluetooth and ANT+ technologies. It is designed to pair with a wide range of training applications, GPS watches, and bike computers, providing accurate heart rate information to enhance your fitness and training experience. This manual provides detailed instructions to help you use and maintain your H6 monitor effectively.
Note: This product is intended for sports purposes only and is not meant to replace any medical device.
2. Standard Accessories
The COOSPO H6 package includes the following items:
- Heart Rate Monitor (H6) x 1 (CR2032 battery installed)
- Chest Strap x 1
- User Manual x 1


3. Setup
Follow these steps to properly set up and wear your H6 Heart Rate Monitor:
- Moisten the Electrode Areas: Lightly moisten the electrode areas on the back of the chest strap with water. This ensures good contact with your skin for accurate heart rate detection.
- Attach the Connector: Attach the H6 heart rate monitor connector to the chest strap. Ensure the side marked 'L' on the connector is positioned towards your left side.
- Wear the Chest Strap: Wear the chest strap around your chest, just below your chest muscles. The COOSPO logo on the connector should be in a central and upright position.
- Adjust for Comfort: Adjust the strap length to ensure a snug but comfortable fit. The moist electrode areas should be firmly against your skin. The adjustable length of the chest strap ranges from 65 to 95 cm.


4. Operating Instructions
The H6 Heart Rate Monitor offers versatile connectivity for various fitness devices and applications.
Connecting to a Smartphone App (Bluetooth)
- Ensure your H6 monitor is worn correctly (as described in Section 3). Your heart rate will power up the sensor.
- Turn on Bluetooth on your smartphone (Settings > Bluetooth > ON).
- Important: Do not attempt to pair the H6 directly from your phone's Bluetooth settings. Instead, open your preferred fitness application (e.g., Strava, Wahoo Fitness, Polar Beat, Zwift, Nike+ Run Club, CoospoRide).
- Within the app, navigate to its sensor or device pairing section and select the H6 monitor from the list of available devices. The Bluetooth name will typically appear as H6M-******.
- Once connected, the app will display your real-time heart rate data.
Connecting to an ANT+ Watch or Bike Computer
- Ensure your H6 monitor is worn correctly (as described in Section 3).
- On your ANT+ compatible watch or bike computer (e.g., Garmin, Wahoo, CooSpo), go to the device settings and search for new sensors.
- Select the H6 from the ANT+ device list.
- Start your training session as prompted by your device, and your heart rate will be displayed in real-time.


Video: COOSPO H6 Heart Rate Monitor product overview and usage demonstration.
5. Maintenance
To ensure reliable measurement and maximize the lifespan of your H6 Heart Rate Monitor, please follow these care instructions:
Heart Rate Connector (H6 Sensor)
- Detach the connector from the chest strap after each use.
- Dry the connector with a soft towel.
- Do not use cleaning chemicals on the connector.
Chest Strap
- Clean the strap under running water after each use and hang it to dry.
- Cleaning the strap in a washing machine or dryer is strictly prohibited.
- Never use cleaning chemicals, as they can cause rapid aging of the strap and shorten its service life.
- Do not stretch the strap or bend the electrode areas sharply.
- Do not store the heart rate monitor wet in non-respirable materials to prevent rapid oxidation. Always dry and store the strap and the connector separately.
- The resistance value of the chest strap may diminish after 300 to 500 washes. For consistently accurate readings, it is recommended to replace the chest strap regularly.
6. Battery Replacement
The H6 Heart Rate Monitor uses a CR2032 coin cell battery. The battery life is approximately 300 hours of continuous use (based on 1 hour of exercise per day).
- Open the Battery Cover: Use a coin to twist the battery cover counter-clockwise until it clicks out of place.
- Remove Old Battery: Carefully remove the old CR2032 battery.
- Dispose of Used Batteries: Properly dispose of used batteries in accordance with local environmental regulations. Do NOT dispose of batteries in household trash or incinerate.
- Insert New Battery: Replace the battery with the positive (+) side facing up.
- Close the Battery Cover: Use a coin to twist the battery cover clockwise until it is securely in place.

⚠️ WARNING: Battery Safety
- INGESTION HAZARD: This product contains a button cell or coin battery. Serious injury or death can occur if ingested. A swallowed button cell or coin battery can cause internal chemical burns in as little as 2 hours.
- KEEP new and used batteries OUT OF REACH of CHILDREN.
- Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
- Do not force discharge, recharge, disassemble, heat above 45°C, or incinerate batteries. This may result in injury due to venting, leakage, or explosion.
- Ensure batteries are installed correctly according to polarity (+ and -).
- Do not mix old and new batteries, different brands, or types of batteries (e.g., alkaline, carbon-zinc, rechargeable).
- Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
7. Troubleshooting
If you encounter issues with your COOSPO H6, try the following solutions:
Connectivity Issues (e.g., won't connect via Bluetooth)
- Check Sensor Connection: Ensure the H6 sensor is properly snapped onto the chest strap.
- Moisten Electrodes & Wear Correctly: The electrodes must be wet and the strap worn against your body in the correct position for the sensor to activate. Your heart rate powers the sensor.
- Pair via App, Not Phone Settings: Remember to connect the heart rate sensor within your fitness app, not directly through your phone's Bluetooth settings.
- Reset App & Reconnect: Try closing and reopening your fitness app, then attempt to reconnect the sensor.
- Check Battery Level: If the above steps fail, the battery may be low. Replace the CR2032 battery as described in Section 6. When replacing, be careful to protect the battery shrapnel.
- Try a Different Chest Strap: If available, test with another chest strap to rule out issues with the strap itself.
Interference with Other Devices (FCC Statement)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
⚠️ Safety & Product Integrity
- Do not open or modify the product.
- Do not disassemble or attempt to service this product.
- This product is safe under normal and reasonably foreseeable operating conditions.
8. Specifications
| Feature | Specification |
|---|---|
| Weight | 15 g (Monitor only) |
| Battery Life | 300 Hours (CR2032) |
| Heart Rate Range | 30 - 240 bpm |
| Waterproof Rating | IP67 (Waterproof for daily life, not suitable for swimming) |
| Wireless Connectivity | Bluetooth 4.0 & ANT+ |
| Size (Monitor) | 60 x 33.8 x 12.2 mm |
| Transmission Distance | Bluetooth: 10 m, ANT+: 6 m |
| Strap Adjustable Length | (L) 65 - 95 cm |


9. User Tips
- Always moisten the electrode areas of the chest strap before wearing it to ensure proper contact and accurate readings.
- Connect the heart rate sensor through your fitness app, not directly via your phone's Bluetooth settings. The sensor's Bluetooth name will typically start with H6M-.
- Separate the sensor from the chest strap after each workout to prolong the life of both components.
- For optimal accuracy, consider replacing the chest strap every 300-500 washes, as its resistance value may decrease over time.
- The H6 does not have a built-in heart rate alarm function. It provides accurate data for you to monitor and plan your training.
10. Warranty & Support
If you encounter any issues or have questions regarding your COOSPO H6 Heart Rate Monitor, please contact COOSPO support through your buyer account. A satisfactory solution will be provided as soon as possible.
If the product is operating improperly and troubleshooting steps do not resolve the issue, please contact COOSPO support. The product may need to be returned to the manufacturer for service or repair.
11. Disclaimer
The product described in this user manual is subject to change without prior notice due to the manufacturer's ongoing development program.
Our company shall not be liable for any damages, losses, costs, or expenses, whether direct, indirect, incidental, consequential, or special, arising out of or related to the use of this material or the products described herein.
Waste Electrical Products Disposal
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information on proper disposal and recycling.