Range Tour Universal Rear View Camera for Range Tour Dash Cams

Contents

Range Tour 1080P Waterproof Rear View Camera

Instruction Manual

1. Introduction

Thank you for choosing the Range Tour 1080P Waterproof Rear View Camera. This camera is designed to provide a clear, wide-angle view behind your vehicle, enhancing safety and convenience when used with compatible Range Tour Car DVR systems. This manual provides essential information for proper installation, operation, and maintenance of your new rear view camera.

2. Safety Information

  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Do not attempt to disassemble or modify the camera, as this will void the warranty and may cause damage.
  • Mount the camera securely to avoid it becoming a projectile in case of sudden stops or accidents.
  • Keep the lens clean and free from obstructions for optimal performance.
  • Always consult a professional if you are unsure about any installation steps, especially those involving vehicle electrical systems.

3. Package Contents

  • Range Tour 1080P Waterproof Rear View Camera
  • 3.5mm to 4-pin Video Cable (available in 6M, 10M, 15M, or 20M lengths)
  • Mounting Screws
  • 3M Adhesive Pad
Range Tour Rear View Camera and 3.5mm cable

Image: The Range Tour rear view camera unit and its connecting 3.5mm video cable.

4. Specifications

Feature Specification
Lens Material Plastic + Glass
Lens Resolution 1920*1080P
Lens Angle 170 Degree
Lens Rotatable 90 Degree
Interface 3.5mm (4-pin)
Shell Material Plastic
Wire or Wireless Wire
Installation Methods Screw / 3M Adhesive
Cable Length Options 6M, 10M, 15M, 20M

5. Installation and Setup

5.1 Compatibility Check

IMPORTANT:

  • This rear camera is compatible with Range Tour D90 4-Channel, D40 3-Channel, and D70 3-Channel Dash Cameras.
  • It is NOT compatible with the D90 3-Channel Dash Camera.
  • It is NOT compatible with Android Streaming Media Mirror Cameras.
  • Please ensure your Car DVR supports this specific model rear camera before installation. If unsure, consult your DVR's manual or contact customer support.

5.2 Mounting the Camera

  1. Choose a Location: Select a suitable location at the rear of your vehicle, typically above the license plate or on the rear bumper, ensuring a clear view and protection from direct impact.
  2. Clean the Surface: Thoroughly clean and dry the mounting surface.
  3. Mounting Options:
    • Screw Mount: Use the provided screws to securely attach the camera bracket to the chosen location. Pre-drilling pilot holes may be necessary.
    • 3M Adhesive Mount: Apply the 3M adhesive pad to the camera bracket and firmly press it onto the cleaned mounting surface for at least 30 seconds. Allow sufficient time for the adhesive to cure before driving.
  4. Adjust Angle: The camera lens is 90-degree rotatable. Adjust the camera angle for the best possible view.
Close-up of Range Tour Rear View Camera

Image: Close-up view of the rear camera unit, showing its adjustable bracket.

5.3 Wiring Connections

  1. Route the Cable: Carefully route the 3.5mm video cable from the rear camera to your compatible Car DVR unit, ensuring it is tucked away safely and does not interfere with vehicle operations. Choose the appropriate cable length (6M, 10M, 15M, or 20M) for your vehicle.
  2. Connect to DVR: Plug the 3.5mm jack of the video cable into the designated rear camera input port on your Car DVR.
  3. Power Connection (if applicable): The 3.5mm cable includes a red wire for power. This wire typically connects to your vehicle's reverse light power supply (12V) to automatically trigger the rear view display when reversing. Consult your DVR's manual for specific wiring instructions.
Detailed view of 3.5mm jack

Image: Detailed view of the 3.5mm jack connector, which connects to the DVR.

4-pin wiring diagram for camera connector

Image: Wiring diagram for the 4-pin connector. Pin 1: Back, Pin 2: VCC (Power), Pin 3: AV (Video Signal), Pin 4: GND (Ground).

6. Operation

Once the rear view camera is correctly installed and connected to your compatible Range Tour Car DVR, its operation is typically managed through the DVR unit itself.

  • Automatic Display: If wired to the reverse light, the rear camera feed should automatically appear on your DVR screen when the vehicle is shifted into reverse gear.
  • Manual Switching: Some DVR models may allow manual switching to the rear camera view via a menu option or dedicated button. Refer to your specific DVR's instruction manual for details.
  • Recording: The rear camera footage will be recorded by your DVR alongside the front camera footage (if applicable), depending on your DVR's settings.

7. Maintenance

  • Cleaning the Lens: Regularly clean the camera lens with a soft, damp cloth to remove dirt, dust, or water spots that may obscure the view. Avoid abrasive cleaners.
  • Checking Connections: Periodically inspect the cable connections to ensure they remain secure and free from corrosion or damage.
  • Cable Integrity: Ensure the video cable is not pinched, cut, or exposed to excessive heat or sharp edges, which could damage the wiring.

8. Troubleshooting

  • No Image on DVR Screen:
    • Verify that the 3.5mm cable is securely connected to both the camera and the DVR.
    • Check the power connection (red wire) if it's connected to the reverse light. Ensure it's receiving power when in reverse.
    • Confirm that your DVR model is listed as compatible (D90 4-Channel, D40 3-Channel, D70 3-Channel).
    • Ensure the DVR is set to display the rear camera input.
  • Poor Image Quality:
    • Clean the camera lens thoroughly.
    • Check for any obstructions blocking the camera's view.
    • Ensure the cable is not damaged or experiencing interference.
    • Verify the DVR's display settings for resolution and brightness.
  • Camera Not Activating in Reverse:
    • Re-check the connection of the red power wire to the reverse light circuit.
    • Confirm the reverse light itself is functioning correctly.
    • Consult your DVR's manual for specific reverse trigger settings.

9. User Tips

  • Verify Compatibility: Always double-check that your existing dash cam model (e.g., D90 4-Channel, D40 3-Channel, D70 3-Channel) is explicitly supported by this rear camera. Incompatible models, such as the D90 3-Channel or Android Streaming Media Mirror Cameras, will not work.
  • Cable Management: When routing the cable, use cable ties or clips to secure it neatly along the vehicle's interior trim. This prevents tangles, damage, and ensures a professional installation.
  • Test Before Finalizing: Before fully securing all components and trim, perform a functional test of the camera with your DVR to ensure everything is working as expected.

10. Frequently Asked Questions (FAQ)

Q: Is this rear camera compatible with any dash cam?
A: No, this camera is specifically designed for Range Tour D90 4-Channel, D40 3-Channel, and D70 3-Channel Dash Cameras. It is not universally compatible with all dash cams, including other brands or specific Range Tour models like the D90 3-Channel.
Q: Can I use this with an Android Streaming Media Mirror Camera?
A: No, this rear camera is not compatible with Android Streaming Media Mirror Cameras.
Q: What is the purpose of the red wire on the 3.5mm cable?
A: The red wire is typically used to connect to your vehicle's reverse light power supply. This allows the DVR to automatically switch to the rear camera display when you put your car in reverse.

11. Support

For further assistance, technical support, or warranty inquiries, please contact Range Tour customer service through your purchase platform or visit the official Range Tour website.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.