DDPAI Mola N3 Pro Dash Camera User Manual

1. Introduction

Thank you for purchasing the DDPAI Mola N3 Pro ultra-high-definition digital Dash Cam. This device offers high-quality captured images and a high-definition video experience, ensuring a comprehensive record of your journeys. The N3 Pro is equipped with a 1/2.7-inch CMOS image sensor, 5-megapixel Ultra HD image, D² save emergency dual storage, 24H parking monitoring, GPS (optional), and built-in Wi-Fi for seamless connection to the DDPAI App.

This manual provides detailed instructions for the installation, operation, and maintenance of your DDPAI Mola N3 Pro Dash Cam. Please read it thoroughly before use.

2. Safety Instructions

2.1 Safety Cautions

• Only suitable for motor vehicles.
• Only suitable for DC12V ~ 24V vehicles.
• Do not place the N3 Pro Dash Cam in a humid environment, or expose it to rain, moisture, or water, as this may cause external or internal damage.
• Do not attempt to disassemble or repair the device without permission. For any issues, contact DDPAI Customer Service.
• Avoid exposing the N3 Pro Dash Cam to overheating or dusty environments. Do not use chemicals or cleaning solvents.
• Clean the lens with a soft, damp cloth. Clean carefully to avoid scratches that could affect video quality.
• Avoid dropping, puncturing, or disassembling the device.
• Do not use the N3 Pro Dash Cam in environments below -4°F (-20°C) or above 158°F (70°C).
• If not in use for a long period, it is better to remove the camera from the vehicle to prevent damage from overheating.
• **TF Memory Card**: Before inserting an external memory card, check for any damages or cracks. Do not use cards with physical distortions or covered cracks, as this poses a risk of short circuits.
• Use only the specified USB car charger included in the package. Using other chargers may cause the Dash Cam to repeatedly restart due to power mismatch.
• Before installation, perform a power-on check to confirm the N3 Pro Dash Cam connects normally to the DDPAI App. If there are issues, contact feedback@DDPAI.com.
• Ensure all required permissions are granted to the DDPAI App for normal function.

2.2 Warnings

Failure to comply with safety warnings and regulations may result in serious injury or death.

• Keep gadgets out of reach of children.
• Be sure to use specified accessories and designated parts. The use of other non-designated parts may damage the equipment and lead to fire, electric shock, or equipment failure.
• If the N3 Pro Dash Cam is damaged or malfunctioning, stop using it immediately and consult the seller. Continued use may cause fires, electric shocks, or vehicle malfunctions.
• Do not install the Dash Cam in areas that may obstruct the driver's sight, including rearview mirrors or airbag outlets.
• Do not place the N3 Pro Dash Cam on the dashboard or in front of airbags when it is not secured.
• Do not install the N3 Pro Dash Cam on the windshield when it is not secured, as it may fall and distract the driver.
• Do not install or perform any operations while driving. If necessary, pull over safely before use.
• Note that due to the wide-angle lens, some images may be distorted and differ from the actual image. This is a characteristic of a wide-angle lens and not a malfunction.
• In some countries or states, drivers are prohibited from installing anything on the windshield or specific areas. Owners/operators should use this equipment in compliance with local laws.

3. Package Contents

3.1 N3 Pro Kit

• 

  Image: Front Package Contents including N3 Pro, Bracket, Car charger, Power cable, User manual, Installation tool, 3M adhesive, Electrostatic stickers.

• N3 Pro Dash Cam
• Power cable
• Mount
• Car charger
• Vehicle Installation Tool
• Adhesive sticker
• Electrostatic sticker
• User manual

3.2 Rear Camera Kit (Optional)

• 

  Image: Rear Package Contents including RC1 Rear Camera, Power cable, User manual, 3M adhesive.

• Rear camera (RC1)
• Rear camera power cable
• Adhesive sticker

If any components are found to be damaged, missing, or waterlogged after unpacking, please contact feedback@DDPAI.com.

4. Product Overview

Image: DDPAI Mola N3 Pro Dash Camera highlighting 2.5K+1080P recording, SR2.0, Supercapacitor, and APP Control.

Image: Illustration of the hidden discreet design and easy installation for both front and rear cameras.

4.1 Main Unit (N3 Pro Dash Cam)

1. Parking monitoring indicator
2. Lens
3. USB Type-C port
4. Indicator light
5. MIC
6. Reset button
7. Mounting bracket
8. Speaker
9. Lock button
10. Micro SD card slot

4.2 Rear Camera (RC1)

11. Rear camera
12. Adhesive sticker
13. Power cable
14. Interface to rear camera

5. Installation

The N3 Pro Dash Cam is factory configured and ready for use after installation.

5.1 Installing the TF Memory Card

• The N3 Pro supports a maximum of 512GB TF memory card and requires a Class 10 high-speed card. Recommended brands include DDPAI, Kingston, Samsung, Toshiba, and Lexar.
• Insert or remove the TF card only when the Dash Cam is not connected to the power supply to avoid damaging files.
• Confirm the orientation of the TF card before insertion to prevent damage to the card or slot.
• Steps:
  1. Open the TF card slot cover on the left side of N3 Pro.
  2. Insert the TF card into the N3 Pro slot (text side upwards, connecting finger side downwards), then push until it clicks.
  3. Close the card slot cover.

• Note:

  The Dash Cam will automatically format the TF card the first time it is used.

5.2 Power-On Checking

• Do not perform any setup operations while driving.
• Downloading the app may incur mobile data usage. Connect to Wi-Fi if preferred.
• Before full installation, perform a power-on check to confirm the N3 Pro Dash Cam connects normally to the DDPAI App.
• Steps:
  1. Scan the QR code on page 6 of the PDF manual to install the DDPAI App on your smartphone. Grant all necessary permissions.
  2. Connect the N3 Pro power cable: Take out the N3 Pro host, holder, vehicle charger, and Type-C power cable. Connect the USB connector of the power cable to the N3 Pro and insert the other end into the power port.
  3. Insert the vehicle charger into the cigarette lighter socket and start the vehicle. The N3 Pro will power on with "Hello, DDPAI". The indicator light will turn blue from purple, indicating normal operation. Refer to the LED Status Light Indicator section for troubleshooting.

5.3 Installing the N3 Pro onto Your Windshield

• Ensure the power-on check is successful and the app is connected.
• Do not install or set up while driving.
• 1. Select an appropriate location and clean the area: Install the N3 Pro on your front windshield, next to the rearview mirror on the driver's side. Clean the area thoroughly to ensure firm attachment.
• 

  Image: Diagram showing the optimal installation position on the windshield.

• Use the vehicle wire trim tool to route the power cable along the front windshield and roof, hiding it on the A-pillar to avoid obstructing the driver's sight.
• 2. Locate the installation position using guidelines: After connecting to the DDPAI App, horizontal and vertical guidelines will appear on the screen.
  • Vertically: Move the N3 Pro side to side until the center of your vehicle's front end aligns with the vertical guideline.
  • Horizontally: Rotate the camera up and down until the ground-level horizon outside vanishes from the horizontal guideline.
• 3. Fix the N3 Pro in place: Attach the electrostatic sticker, remove the red backing film from the 3M adhesive, and firmly attach the N3 Pro to the predetermined location, ensuring the camera faces forward.

5.4 (Optional) Installing the Rear Camera

• This section is only for users who purchased the rear camera.
• 1. Clean the rear windshield: The approximate installation position is shown in the figure below.
• 

  Image: Diagram illustrating the rear camera installation position and 360° rotation capability.

• 2. Connect the rear camera and power cable: Take out the rear camera and its power cable and connect them.
• 3. Insert the rear power cable fully into the N3 Pro headphone jack.

  Caution:

  Ensure the power cable is fully plugged in; otherwise, the rear camera indicator will not light up, and the camera will not work.
• 4. Route the rear power cable: Route the cable from the N3 Pro to the rear camera as shown in the figure.
• 5. Fix the rear camera: Remove the red backing film from the adhesive, adjust the field of view, and fix the rear camera to the inner wall of the rear windshield.

5.5 Hardwire Kit Installation (Optional)

To avoid vehicle damage from incorrect operation, have the hardwire kit installed by a professional auto service center. If you have purchased a hardwire kit, you can connect it directly to the N3 Pro through the fuse box for power supply. This method enables the 24H parking monitoring function.

• Ensure personal safety and turn off the vehicle engine before proceeding.
• The mobile App must be verified to connect to the N3 Pro after startup.
• The N3 Pro should be adjusted for shooting view and attached to the front windshield.
• 1. Identify wire terminals: The power connector includes Red ACC wire terminal, Yellow VCC wire terminal, Black GND wire terminal, and a Type-C connector end.
• 

  Image: Wiring diagram for the hardwire kit, showing connections for ACC, VCC, and GND.
• 2. Install the Dash Cam and power it on:
  1. Insert the Type-C end of the power wire into the Dash Cam power interface. Route the power wire along the front windshield, A-pillar, and driver's seat storage compartment to the fuse box.
  2. Connect the terminal cables:
     a. Connect the black wire (GND) to the ground wire inside the vehicle fuse box.
     b. Connect the red wire (ACC) to the +12VDC power supply control of the fuse box.
     c. Connect the yellow wire (VCC) to the 12VDC power supply of the fuse box (this power supply is always on and not controlled by the ignition).
  3. Start the vehicle. The Dash Cam will automatically start up and emit a startup prompt tone.
  4. Check if the Dash Cam is working properly.

6. Operation

6.1 LED Status Light Indicator

6.2 Loop Recording

The device automatically starts recording after powering on without any additional settings required. Previous recordings will be overwritten in a loop when storage is full. Emergency events will be locked and not be overwritten.

Note:

Image: Chart showing approximate recording times for different Micro SD card capacities (16G to 512G).

6.3 DDPAI App Setup and Connection

The Dash Cam connects to the DDPAI App via its built-in Wi-Fi, creating a small Dash Cam-smartphone WLAN. This allows for real-time preview, playback, download, and sharing of driving recordings and photos.

• 1. Download and Install the DDPAI App: Scan the QR code on page 6 of the PDF manual or download from Google Play/App Store. Grant all necessary permissions during installation.
• 2. Connecting N3 Pro to the DDPAI App:
  1. On the Device main page of the DDPAI App, tap "+ Connect new devices" and select "Screen-less Dash Cam".
  2. On the wizard page, tap "Next" and "Connect Wi-Fi". The detected Dash Cam Wi-Fi (e.g., DDPAI_N3 Pro_XXXX) will be displayed. Tap "Connect".
  3. Connect your smartphone to the Dash Cam's built-in Wi-Fi "DDPAI_N3 Pro_XXXX" with the default password: 1234567890.

• Note:

  If you forget the Wi-Fi password, press and hold the rightmost button on the Dash Cam for 6-8 seconds to restore factory settings.

• Note:

  When connecting for the first time, you may be prompted to enable high compression video encoding. It is recommended to choose "Enable" for improved video quality.

6.4 24H Parking Monitoring Mode

This function is only available to users who have purchased the hardwire kit. After installing the DDPAI intelligent hardwire kit to the fuse box, the Parking Mode setting will appear in the DDPAI App's camera settings.

• 

  Image: Features of 24H Parking Monitoring including Low-power Consumption Protection, Low Voltage Protection, Time Lapse, and Collision Detection.
• 8.1 After vehicle is turned off enters:

  Options	Description
  Time-Lapse Recording	Saves considerable storage space; playback speed will be faster. (Default)
  Normal Recording	Records continuously and overwrites oldest files when storage is full.
  Sleep Mode	Device goes into sleep mode and awakens when an emergency event is detected.

• 8.2 Setting Parking Monitoring Duration: The device will go into sleep mode after the vehicle engine is turned off for a set duration (12H, 24H, 48H; 24H default). Consider monitoring duration to avoid battery depletion.
• 8.3 Vehicle Battery Protection: Set the minimum safe voltage (default Middle (12V)). The recorder will automatically shut down if the battery voltage drops below this level to prevent continuous battery depletion. You can view real-time battery voltage detection in the app.

6.5 GPS Function

The N3 Pro Dash Cam supports GPS function, which is turned on by default. When in an open outdoor area, it can receive GPS signals. GPS information (time, speed, altitude, direction, driving track) will be recorded in your video and viewable in the DDPAI App.

Note:

Image: Sense Reality Skin 2.0 interface showing GPS tracking data like location, speed, route, and time.

6.6 Sense Reality 2.0 Racing Mode

Combined with built-in GPS, G-sensor, and a 3-axis gyro, the innovatively developed SR 2.0 skin effect provides an immersive racing experience, allowing you to visualize driving data.

6.7 APP Control

With built-in 2.4GHz WiFi, the DDPAI App allows you to set up the dashcam, watch live streaming, replay or download videos, and perform OTA firmware updates. Easy-to-use tools enable you to create cinematic masterpieces with special effects, filters, and music, and share your vlogs.

Note:

Image: Screenshots of the DDPAI App interface showing preview, playback, download, editing, and sharing options.

7. Maintenance

7.1 Cleaning

• Clean the lens with a soft, damp cloth. Clean carefully to avoid scratches that could affect the quality of the video.
• Do not use chemicals or cleaning solvents to clean the device.

7.2 File Browsing on PC

1. Disconnect the power cable from the N3 Pro Dash Cam to turn it off.
2. Open the card slot cover and gently push the TF memory card to eject it.
3. Remove the TF memory card and insert it into the accompanying card reader, then plug the card reader into the PC.
4. Once the PC recognizes the TF memory card, open the DCIM folder. Files are organized into three folders:
   • 200video: Includes normal and time-lapse recording videos. Normal videos start with a number, time-lapse videos start with "S", and high-compression encoded videos end with "H".
   • 201photo: Includes voice-activated photos and photos generated by collision detection. Normal photos start with "N", collision detection photos start with "G".
   • 202emergency: Includes emergency video files saved when a collision occurs.

7.3 Firmware Upgrading

1. Open the DDPAI App, connect to the Dash Cam's Wi-Fi, and go to "Me" > "About DDPAI" > "Check for New Version".
2. The app will automatically check for updates. Follow prompts to upgrade if a new version is available.
3. During firmware upgrade, do not turn off the power to avoid damage. If a power outage occurs and the upgrade fails, contact customer service, download the latest upgrade package, copy it to the Dash Cam via a TF card, and then upgrade.

8. Troubleshooting (FAQ)

Q1: TF Card error?

1. The TF card must be formatted before first use.
2. The Dash Cam supports up to 512GB. Use a high-speed Class 10 card from recommended brands like DDPAI, Kingston, Samsung, Toshiba, or Lexar.

Q2: Rear camera abnormal, unable to switch?

Check if the rear camera indicator light is on (steady green). If not:

1. Ensure there is no gap between the bracket and the Dash Cam.
2. Check if the rear camera connection cable is fully inserted into the headphone jack on the bracket.
3. If issues persist, contact feedback@DDPAI.com.

Q3: Forgot the Dash Cam's Wi-Fi password?

Press and hold the reset key with a pin for 6-8 seconds to restore factory settings. The initial default Wi-Fi password is "1234567890".

Q4: Unable to connect to Wi-Fi?

1. Turn off VPN and other security software when connecting.
2. Grant all requested application permissions during App installation.
3. Reset the device and reinstall the DDPAI App.
4. If issues persist, contact feedback@DDPAI.com.

Q5: Real-time preview on iPhone is black screen?

Turn on Local Network. Find DDPAI App in iPhone settings and enable "Local Network".

Q6: After starting the vehicle, is it necessary to unplug and then plug back in the USB adapter for the Dash Cam to turn on?

For Dash Cams powered by the car's cigarette lighter, some car models continue to supply power even after the engine is off. If the Dash Cam doesn't detect the power on/off signal, you may need to manually unplug and re-plug the power cable to start it.

Q7: The GPS location is not successful?

1. Ensure there is no gap between the bracket and the Dash Cam.
2. Check if there is a GPS logo on the bracket.
3. Try again in an area with a good GPS signal (outside the car).
4. Restart or reset the device.

Q8: The date/time of the Dash Cam is not accurate?

Connect the Dash Cam to the DDPAI App to synchronize the time automatically. If time synchronization is consistently an issue, the internal RTC of the Dash Cam may be faulty. Contact us for assistance.

Q9: Video playback is stuttering?

1. It is recommended to download the video for playback.
2. If the storage hasn't been formatted for a long time, format it or try using a different TF card.

Q10: The Dash Cam automatically shuts down after being idle on constant power for 15 minutes?

The Dash Cam will enter sleep mode after a long period of inactivity. Restart it by unplugging and plugging the power cable again.

9. Specifications

Image: Detailed table of product parameters including Brand, Model, Processor, Input, Dimensions, WiFi & GPS, Recording, Lens, G-sensor, and Storage.

10. User Tips

• Memory Card Quality: For optimal performance and to prevent storage issues, always use a high-quality Class 10 Micro SD card from recommended brands like Lexar, Kingston, Samsung, or Toshiba. Official DDPAI memory cards are highly recommended.
• Parking Monitoring: To enable 24-hour parking monitoring, an external IPS hardwire kit is required and sold separately. This kit ensures the dash cam records while parked without draining your car battery.
• App Connection: If you experience issues connecting to the DDPAI App, ensure all necessary app permissions are granted and try turning off any VPN or security software temporarily. Resetting the device and reinstalling the app can also help.
• Video Playback: For smoother video playback, it is recommended to download the video to your phone or PC first, rather than streaming directly from the dash cam. Regularly format your memory card to maintain optimal recording performance.
• GPS Accuracy: GPS signal reception can be affected by environmental factors such as dense urban areas, underground parking, tunnels, and cloudy weather. Ensure your vehicle is in an open area for best GPS performance.
• Automatic Power On: The dash cam is designed to power on automatically when the vehicle starts. If it doesn't, and your car's cigarette lighter provides constant power, you might need to manually unplug and re-plug the USB adapter.
• Rear Camera Issues: If the rear camera is not working, check that the green indicator light is on, the bracket is securely attached, and the power cable is fully inserted into the N3 Pro's headphone jack.

11. Support

For any questions, suggestions, or technical support, please contact DDPAI Customer Service via email at feedback@DDPAI.com.

You can also visit the official website for more information: https://en.DDPAI.com.

A detailed user manual in PDF format is available for download: User manual (PDF).