1. Introduction
The HORACO ZX-SWTG3424S is a high-performance 28-port Layer 3 Managed Ethernet Switch designed for small to medium-sized network access layers, convergence layers, and core layers. It features 24 Gigabit Ethernet ports and 4 10 Gigabit SFP+ uplink optical ports, offering a robust solution for stable, flexible, and scalable network infrastructure. This switch supports advanced network management functions including routing, VLAN, DHCP, QoS, and various security protocols to ensure reliable and efficient data transmission.
Figure 1: HORACO 28-Port 10Gigabit Managed Ethernet Switch (Front View)
2. Setup
2.1 Unpacking and Package Contents
Carefully unpack the switch and verify all components are present. If any items are missing or damaged, please contact customer support.
- 1 x HORACO ZX-SWTG3424S Managed Ethernet Switch
- 1 x User Manual
- 1 x Certificate
- 1 x Power Cord
- 1 x Serial Port Line
- 1 x Pair of Lugs (for rack mounting)
2.2 Physical Installation
The switch is designed for 1U rackmount installation. Ensure the installation environment meets the following criteria:
- Temperature: Operating temperature range is -10°C to 50°C.
- Humidity: Operating humidity is 10% to 90% (non-condensing).
- Ventilation: Ensure adequate airflow around the switch for proper heat dissipation. The iron protective shell provides strong thermal conductivity.
- Power: Connect to an AC100-240V, 50/60Hz power source. The switch supports 6KV lightning protection and 8KV anti-static protection.
- Grounding: Connect the grounding hole on the rear panel to a proper earth ground to prevent electrical hazards and improve stability.
Figure 2: Environmental considerations for switch operation, including temperature and lightning protection.
2.3 Initial Connection
Connect the power cord to the power interface on the rear panel and plug it into a suitable power outlet. Use the provided serial port line to connect the RJ45 Console Port to a computer for initial configuration via CLI (Command Line Interface).
Figure 3: Port layout showing 24 RJ45 ports, 4 SFP+ ports, Console port, USB port, and Power Interface with Grounding Hole.
3. Operating the Switch
3.1 Network Configuration
The HORACO ZX-SWTG3424S supports a wide range of network protocols and functions for flexible network management:
- VLAN: Supports up to 4096 VLANs (IEEE 802.1q) for network segmentation and traffic isolation.
- DHCP: Dynamic Host Configuration Protocol for automatic IP address assignment.
- MAC Address Management: Supports 16K MAC address table.
- ACL (Access Control List): For granular control over network traffic.
- QoS (Quality of Service): Prioritize critical network traffic (IEEE 802.1p).
- Multicast: Efficient delivery of data to multiple destinations.
- Storm Control: Prevents network performance degradation due to broadcast, multicast, or unknown unicast storms.
- Link Aggregation: Supports static aggregation to increase link bandwidth and provide load balancing.
Figure 4: Overview of powerful processing capabilities including Spanning Tree Protocol, DHCP, QoS, Routing, Storm Suppression, IPv6, VLAN, MAC Address, ACL Access Control, Link Convergence, and Multicast.
3.2 Layer 3 Features
As a Layer 3 managed switch, it offers advanced routing capabilities:
- Layer 3 Interface: Supports IPv4 and IPv6 address configuration, ARP configuration, and ND configuration.
- Layer 3 Routing: Supports IPv4 static routing, IPv6 static routing, RIP V1/V2, and OSPF.
3.3 Management Interfaces
The switch can be managed using various methods:
- Web-based Management: Access the switch's graphical user interface (GUI) via a web browser.
- Telnet/CLI: Command Line Interface for advanced configuration and troubleshooting.
- SSH: Secure Shell for encrypted remote management.
3.4 Network Protection and Redundancy
The switch incorporates robust mechanisms for network reliability and security:
- Spanning Tree Protocol (STP/RSTP/MSTP): Eliminates two-layer loops and provides link backup.
- ERPS Ring Network Protocol: Supports ring detection and self-healing functions with a recovery time of less than 12ms, ensuring uninterrupted network services.
- Security Functions: Includes 802.1X Authentication, ARP Intrusion Detection, IP Source Guard, and DoS Protection to prevent malicious attacks.
Figure 5: Diagram illustrating the <12ms ring network self-healing capability.
Figure 6: Explanation of reliable network protection mechanisms including STP/RSTP/MSTP, link backup, security functions, and static aggregation.
4. Maintenance
- Environmental Control: Maintain the operating temperature and humidity within the specified ranges to ensure optimal performance and longevity.
- Cleaning: Regularly clean the exterior of the switch with a soft, dry cloth. Ensure ventilation openings are free from dust and obstructions. Do not use liquid or aerosol cleaners.
- Firmware Updates: Periodically check the manufacturer's website for firmware updates. Keeping the firmware up-to-date can improve performance, add new features, and address security vulnerabilities.
- Cable Management: Ensure all network cables are properly organized and secured to prevent accidental disconnections or damage.
5. Troubleshooting
- No Power: Check the power cord connection and the power outlet. Verify the PWR indicator light is on.
- No Network Connectivity: Check cable connections to the switch ports. Verify the Link/ACT indicator light for the connected port is active. Ensure correct IP configuration on connected devices.
- Slow Network Performance: Check for network loops (ensure STP/RSTP/MSTP is configured correctly). Monitor for network storms. Verify port speeds and duplex settings.
- Management Access Issues: Ensure the correct IP address and credentials are used for Web, Telnet, or SSH access. Verify network connectivity to the switch's management interface.
- Indicator Lights:
- PWR: Solid green indicates power is on.
- SYS: Indicates system status (e.g., blinking during boot, solid when operational).
- Link/ACT: Solid green indicates a valid link, blinking indicates data activity.
6. Specifications
| Feature | Description |
|---|---|
| Product Name | 28 Port 10 Gigabit Uplink 24 Port Gigabit Three-Layer Management Ethernet Switch |
| Model Number | ZX-SWTG3424S |
| Port Definition | 24 x 10/100/1000Mbps RJ45 Ports, 4 x 10 Gigabit SFP+ Optical Ports, 1 x RJ45 Console Port, 1 x USB Port |
| Switch Type | Ethernet, Managed, Layer 3 |
| Network Protocols | IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3ae, 802.3az, 802.3ad, 802.3x, 802.1ab, 802.1p, 802.1q, 802.1x, 802.1d, 802.1s, 802.1w |
| Network Transmission Medium | 10Base-T (Cat3, 4, 5 or above UTP/STP <= 100m), 100Base-TX (Cat5 or above UTP/STP <= 100m), 1000Base-TX (Cat5 or above UTP/STP <= 100m), Multimode Optical Fiber (50/125, 62.5/125, 100/140um), Single Mode Optical Fiber (8/125, 8.7/125, 9/125, 10/125um) |
| Indicator Lights | PWR, SYS, Link/ACT |
| Switching Capacity | 128Gbps |
| Packet Forwarding Rate | 95.23Mpps |
| Memory (DDR SDRAM) | 128MB |
| Flash Memory | 16MB |
| Packet Cache | 12Mbit |
| MAC Address Table | 16K |
| Jumbo Frame | 12Kbytes |
| VLANs | 4096 |
| MTBF (Mean Time Between Failures) | 100,000 hours |
| Operating Temperature | -10°C to 50°C |
| Storage Temperature | -40°C to 70°C |
| Operating Humidity | 10% to 90% (non-condensing) |
| Storage Humidity | 5% to 90% (non-condensing) |
| Power Input | AC100-240V, 50/60Hz |
| Dimensions (LxWxH) | 440mm x 205mm x 44mm |
| Product Net Weight | 2.53 Kg |
| Product Gross Weight | 3.14 Kg |
| Certifications | CE, FCC, RoHS |
| Warranty | 2 Years |
Figure 7: Detailed product parameters and specifications.
7. Warranty and Support
The HORACO ZX-SWTG3424S Managed Ethernet Switch comes with a 2-year free warranty. HORACO also provides lifetime professional technical support for this product. For any technical assistance or warranty claims, please contact HORACO customer service.
Figure 8: Certifications (CE, FCC, RoHS) and power plug types.
8. User Tips
- Plan Your Network: Before deployment, plan your network topology, IP addressing scheme, and VLAN configurations to ensure efficient and secure operation.
- Secure Management Access: Always change default passwords for management interfaces (Web, Telnet, SSH) and use strong, unique passwords. Consider restricting management access to specific IP addresses.
- Regular Monitoring: Utilize SNMP (Simple Network Management Protocol) for continuous monitoring of switch performance and network traffic.
- Proper Cabling: Use high-quality Cat5e/6/7 Ethernet cables for Gigabit connections and appropriate SFP/SFP+ transceivers and fiber optic cables for 10 Gigabit SFP+ ports to ensure optimal performance.
- Backup Configuration: Regularly back up your switch configuration to prevent data loss in case of unexpected issues.