SHIMANO NEXUS C6000 Series

Contents

SHIMANO NEXUS C6000 Internal Geared Hub and Shift Lever Instruction Manual

Model: NEXUS C6000 Series

Brand: SHIMANO

Introduction

This manual provides detailed instructions for the installation, adjustment, maintenance, and safe operation of the SHIMANO NEXUS C6000 series internal geared hubs and compatible shift levers. The NEXUS 8-speed system is designed for high levels of design, quality, and function, incorporating SHIMANO's unique Gear Change Support mechanism for smooth, low-effort shifting.

This manual covers the following models:

  • Internal Geared Hubs: SG-C6000-8C, SG-C6001-8D, SG-8C20
  • Shift Levers: SL-C6000-8, SL-S500, SL-S7000-8
  • Cassette Joint: CJ-8S20

For a comprehensive dealer's manual, please refer to the official PDF document: SHIMANO NEXUS Dealer's Manual (PDF).

Important Safety Information

WARNING: Failure to follow these instructions could result in death or serious injury.

  • This manual is intended primarily for professional bicycle mechanics. Users not professionally trained should not attempt installation without assistance from a local bicycle dealer.
  • Always use genuine SHIMANO parts. Incorrect assembly or adjustment can lead to component failure and loss of control.
  • Wear approved eye protection during maintenance.
  • Learn proper braking technique for your bicycle model, including lever pressure and control characteristics. Improper use can lead to loss of control, falls, or collisions.
  • Use brake levers with mode switching mechanisms only in the specified combinations. Incorrect mode selection can result in excessive or insufficient braking force.
  • Ensure wheels are securely fastened before riding.
  • When securing the brake arm to the frame, use an arm clip matching the chainstay size and tighten securely to the specified torque. Use a lock nut with nylon insert. Failure to do so can cause the brake arm to rotate, leading to sudden handlebar jerks or wheel lock.
  • Install correct non-turn washers on both sides of the hub axle and tighten hub nuts securely. Incorrect installation can cause the hub axle to rotate or cassette joint to turn, leading to serious accidents.
  • Keep fingers away from rotating disc brake rotors, as they are sharp.
  • Do not touch calipers or disc brake rotors while riding or immediately after dismounting, as they can become hot and cause burns.
  • Prevent oil or grease from contacting disc brake rotors and pads. Contamination can impair braking performance and lead to serious injury. If contamination occurs, consult a dealer.
  • Check brake pad thickness; do not use if 0.5 mm or less.
  • Do not use cracked, deformed, or excessively worn disc brake rotors (thickness 1.5 mm or less, or aluminum surface visible).

CAUTION: Failure to follow these instructions could cause personal injury or physical damage.

  • Shift one gear at a time, reducing pedal pressure. Forcing multi-shifting under strong pedaling can cause feet to slip off pedals or the bicycle to fall.
  • The outer casing may spring out of the shifter during multi-shifting to a lighter gear, but this does not affect shifter capabilities as it returns to its original position.
  • When using the brake frequently, do not touch the area around the brake for at least 30 minutes after riding, as it may become hot.
  • For coaster brakes, avoid continuous application on long slopes to prevent overheating, reduced braking performance, and loss of brake grease. Spin the wheel to confirm correct braking force.

Specifications

SHIMANO NEXUS C6000 Series Overview
ComponentModel NumbersDescription
Internal Geared Hub (Coaster Brake + Disc Brake)SG-C6000-8CD8-speed hub with both coaster and disc brake compatibility.
Internal Geared Hub (Disc Brake)SG-C6000-8D, SG-C6001-8D8-speed hub with disc brake compatibility. Improved shifting performance under high chain tension.
Internal Geared Hub (Coaster Brake)SG-C6000-8C, SG-8C20, SG-8C318-speed hub with coaster brake compatibility. Aesthetic enhancements for everyday riding.
Internal Geared Hub (INTER M Brake)SG-C6010-8R, SG-C6000-8R, SG-8R31, SG-8R368-speed hub with INTER M brake compatibility.
Internal Geared Hub (V-BRAKE)SG-C6010-8V, SG-C6000-8V, SG-8R31-VS, SG-8R36-VS8-speed hub with V-BRAKE compatibility.
RAPIDFIRE PLUS ShifterSL-7550, SL-S500, SL-S7000-88-speed shift lever for quick and precise gear changes.
REVOSHIFT ShifterSL-8S31, SL-8S30, SB-8S20-A, SL-C6000-88-speed twist grip shifter.
Cassette JointCJ-8S40, CJ-NX40, CJ-8S20, CJ-NX10Component for connecting the shifting cable to the hub.

General Product Properties:

  • Category: Bearing Hub
  • Number of Holes: 36 Holes
  • Spoke Hole: 29 - 36
  • Hub Hole Number: 32/36 Holes
  • Origin: Japan (Jp)

List of Tools to be Used

ToolDescriptionUsage for
2 mm hexagon wrench
3 mm hexagon wrenchTightening for lever installation (2-2.5 N·m)
5 mm hexagon wrenchTightening for lever installation (6-8 N·m)
10 mm spannerTightening for inner cable fixing bolt unit (3.5-5.5 N·m), Brake arm (2-3 N·m)
Screwdriver [#1]Loosening lever screws, tightening cover fixing screws (0.1-0.2 N·m for REVOSHIFT, 0.2-0.4 N·m for SB-8S20-A/SB-C3000-7)
Screwdriver [#2]Tightening indicator unit (0.3-0.5 N·m)
Adjustable wrenchTightening hub nuts (30-45 N·m), Disc brake rotor fixing lock ring (40 N·m)
TL-LR10Disc brake rotor fixing lock ring toolFor Center Lock type disc brake rotor
TL-CJ40 (Y70898020)Setting toolFor inner cable fixing bolt unit installation (CJ-NX10/CJ-8S20, CJ-NX40/CJ-8S40)
Hexalobular [#25]Tightening for 5 screw type disc brake rotor (2-4 N·m)

Setup and Installation

1. Installation of the Sprocket to the Hub

For 7-speed and 5-speed hubs:

  1. Place the right-hand dust cap onto the driver on the right side of the hub body.
  2. Install the sprocket and secure it in place with the snap ring.

Applicable sprockets: 7-speed (16T-23T outward, 18T-23T inward), 5-speed (16T-23T outward).

Sprocket installation diagram for 7-speed and 5-speed hubs
Diagram showing the installation of the sprocket, dust cap, and snap ring onto a 7-speed/5-speed hub.

For 8-speed hubs (Specification A):

  1. Place the right-hand dust cap C onto the driver on the right side of the hub body.
  2. Install the sprocket and secure it in place with the snap ring.

Applicable sprockets: 16T-23T (outward), 20T-23T (inward).

Sprocket installation diagram for 8-speed hubs
Diagram showing the installation of the sprocket, dust cap, and snap ring onto an 8-speed hub.

NOTICE:

  • If using an inward assembling sprocket with 19T or fewer, or for belt drive specifications, right-hand dust cap A may contact the chain/pulley. Use Specification B instead.
  • For Specification B, if using an inward assembling sprocket with 16T and 3mm teeth or for belt drive specifications, remove right-hand dust cap B before use.

2. Installation of the Cassette Joint to the Hub

The cassette joint should only be used with sprockets from 16T to 23T.

For 7-speed hubs:

  1. Install the driver cap to the driver on the right side of the hub body.
  2. Turn the pulley of the cassette joint in the direction of the arrow so that the yellow mark is aligned with the yellow triangle mark.
  3. Align the yellow marks on the cassette joint with the yellow marks on the right side of the hub body.
Cassette joint installation for 7-speed hub
Diagram illustrating the alignment and installation of the cassette joint on a 7-speed hub.

For 8-speed and 5-speed hubs:

  1. Install the driver cap to the driver on the right side of the hub body.
  2. Secure the cassette joint to the hub with the cassette joint mounting ring. Align the yellow mark with the yellow dot on the pulley, then turn the mounting ring 45° clockwise.
Cassette joint installation for 8-speed and 5-speed hubs
Diagram showing the cassette joint installation for 8-speed and 5-speed hubs, including the 45-degree turn.

3. Installing the INTER M Brake to the Hub Body

  1. Engage the splines on the hub body with the splines on the INTER M brake.
  2. Provisionally tighten the brake unit fixing nut.
INTER M brake installation diagram
Diagram illustrating how to engage the INTER M brake with the hub body splines.

4. Installation of the Hub to the Frame

  1. Mount the chain on the sprocket.
  2. Set the hub axle into the rear dropout.
  3. Place non-turn washers onto the right and left sides of the hub axle. Turn the cassette joint so its protrusions fit into the grooves in the rear dropouts and align parallel to the chainstay.
  4. Tighten hub nuts to 30-45 N·m using an adjustable wrench.
  5. For INTER M brake specifications, attach the brake arm to the chainstay with the brake arm clip. Lightly tighten the clip bolt and clip nut.
  6. If hub nuts are cap nuts, use a frame with rear dropouts at least 7 mm thick.
  7. Check that the brake unit is firmly secured to the hub with the brake unit fixing washer.
  8. Securely tighten the brake arm to the chainstay with the arm clip. Tighten clip bolt and clip nut to 2-3 N·m using a screwdriver [#1] and 10 mm spanner.
Hub installation to frame with non-turn washers
Diagram showing the placement of non-turn washers and cassette joint during hub installation.

NOTICE:

  • Use a non-turn washer that matches the shape of the rear dropout. Different non-turn washers are used for left and right sides.
  • When installing the arm clip, securely tighten the clip bolt while holding the clip nut with a 10 mm spanner.
  • After installing the arm clip, check that the clip bolt protrudes about 2 to 3 mm from the end face of the clip nut.

5. Installation of the Disc Brake Rotor

For Center Lock type:

  1. Attach the disc brake rotor and tighten the disc brake rotor fixing lock ring to 40 N·m using an adjustable wrench and TL-LR10 tool.
Center Lock disc brake rotor installation
Diagram showing the installation of a Center Lock disc brake rotor with the TL-LR10 tool.

For 5 screw type (with lock washer):

  1. Attach the disc brake rotor and the disc brake rotor lock washers to the hub.
  2. Tighten them with screws to 2-4 N·m using a Hexalobular [#25] tool.
  3. Wear gloves and turn the disc brake rotor clockwise with some force. Tighten the screws in the indicated order (1-5).

NOTICE:

  • Fit lock washers so that the marking "TOP" is visible and hooked parts are caught on the notches in the disc brake rotor.
  • Do not reuse lock washers; always use new ones.
  • Use dedicated disc brake rotor fixing screws.

6. Installation of the Lever

When equipped with mode switching mechanism:

  1. Use screwdriver [#1] to loosen the screw.
  2. Set the mode switch to the mode position for the brake installed (C-R for cantilever/roller brakes, V for V-BRAKE).
Lever mode switch adjustment
Image showing the mode switch on the lever for different brake types.

For REVOSHIFT shifter:

  1. Install the lever as shown in the illustration.
  2. Tighten the fixing screw to 2-2.5 N·m using a 3 mm hexagon wrench.

TECH TIPS:

  • If using SHIMANO half grip, the straight section of the handlebar should be 166 mm or longer. Attach the REVOSHIFT shifter to this straight section.
  • Leave a gap of 0.5 mm between the REVOSHIFT shifter and the half grip.
REVOSHIFT shifter installation
Diagram showing the installation of the REVOSHIFT shifter on the handlebar.

For RAPIDFIRE PLUS shifter:

  1. Install the lever as shown in the illustration.
  2. Tighten the fixing screw to 6-8 N·m using a 5 mm hexagon wrench.
RAPIDFIRE PLUS shifter installation
Diagram showing the installation of the RAPIDFIRE PLUS shifter on the handlebar.

7. Installation of the Shifting Cable

For information on how to replace the inner cable, refer to the maintenance section.

NOTICE:

  • Use a shifting cable with one inner cable drum (OT-SP41).
  • Make sure the sealed outer cap is at the shifter end.

For CJ-NX10 / CJ-8S20:

  1. Pass the inner cable through the OT-SP41 outer casing to the end with the plastic cap.
  2. Set the REVOSHIFT shifter/shifter to 1.
  3. Attach the inner cable fixing bolt unit to the inner cable using the setting tool TL-CJ40 (Y70898020). Tighten to 3.5-5.5 N·m using a 10 mm spanner.
  4. Bring the cable around to the cassette joint pulley, hold the inner cable fixing nut facing outwards, and slide the flats part of the inner cable fixing washer into the gap in the pulley.
  5. Turn the cable 60° counterclockwise and attach it to the hook.
  6. Attach the inner cable to the pulley, pass it through the slit in the cassette joint bracket, and insert the outer casing securely into the outer casing holder section.
  7. Fix the cable on the frame with outer casing bands (10 cm and 15 cm from the ends).

TECH TIPS:

  • If cutting the outer casing, cut it near the end with the plastic cap while the cap is still attached. Make the cut end perfectly round.
  • If it's difficult to insert the outer casing into the holder, insert a 2 mm hexagon wrench or #14 spoke into the pulley hole and turn the pulley to align the inner cable fixing bolt unit.
Shifting cable installation for CJ-NX10/CJ-8S20
Diagram showing the routing and attachment of the shifting cable to the cassette joint and frame.

For CJ-NX40 / CJ-8S40:

  1. Set the REVOSHIFT shifter/shifter to 1.
  2. Install the rubber cover and rubber bellows to the outer casing holder body.
  3. Wipe off any grease on the inner cable.
  4. While holding the end of the rubber bellows, insert the inner cable.
  5. Slide the rubber bellows onto the inner cable.
  6. Insert the outer casing into the rubber cover and set it into the outer casing holder body. Push the outer casing securely.
  7. Attach the inner cable fixing bolt unit to the inner cable using the setting tool TL-CJ40 (Y70898020). Tighten to 3.5-5.5 N·m using a 10 mm spanner.
  8. Bring the cable around to the cassette joint pulley, hold the inner cable fixing nut facing outwards, and slide the flats part of the inner cable fixing washer into the gap in the pulley.
  9. Turn the cable 60° counterclockwise and attach it to the hook.
  10. Mount the inner cable into the pulley, through the slit in the cassette joint bracket, and insert the outer casing holder body securely.
  11. Fix the cable on the frame with outer casing bands.

NOTICE:

  • Be careful not to pierce the rubber bellows with the end of the inner cable.
  • Use a new inner cable; do not use a cable with a cut end.

TECH TIPS:

  • For CJ-NX40 and CJ-8S40, use the reverse side of TL-CJ40.
  • If it's difficult to insert the outer casing holder body, insert a 2 mm hexagon wrench or #14 spoke into the pulley hole and turn the pulley to align the inner cable fixing bolt unit.
Shifting cable installation for CJ-NX40/CJ-8S40
Diagram showing the routing and attachment of the shifting cable for CJ-NX40/CJ-8S40, including rubber components.

Adjustment

1. Adjusting the Cassette Joint

  1. Repeatedly move the REVOSHIFT shifter/shifter from the low position to the top position to condition the shifting cable.
  2. Set the REVOSHIFT shifter/shifter to 1.
  3. Set the REVOSHIFT shifter/shifter as shown in the illustration (7-speed/8-speed hub: Set to 4; 5-speed hub: Set to 3).
  4. Check that the yellow setting lines on the cassette joint bracket and pulley are aligned with each other. If the overlapping area falls short of two thirds of each setting line, the gears may not be properly engaged.
  5. After adjusting, cut off the excess length of inner cable and install the inner end cap.

TECH TIPS:

  • If yellow setting lines are not aligned, turn the cable adjustment barrel of the REVOSHIFT shifter/shifter to align them. Then move the shifter from X to Y and back to X, and re-check.
  • The yellow setting lines on the cassette joint are located in two places; use the one easiest to see.
Cassette joint adjustment diagram
Diagram illustrating the alignment marks for cassette joint adjustment.

Maintenance

1. Disconnecting the Shifting Cable (when removing rear wheel)

For CJ-NX10 / CJ-8S20:

  1. Set the REVOSHIFT shifter/shifter to 1.
  2. Pull out the outer casing from the outer casing holder section of the cassette joint, and remove the inner cable from the slit in the bracket.
Shifting cable disconnection for CJ-NX10/CJ-8S20
Diagram showing how to disconnect the shifting cable from the cassette joint.

For CJ-NX40 / CJ-8S40:

  1. Set the REVOSHIFT shifter/shifter to 1.
  2. Hold the rubber cover and remove the outer casing holder body from the cassette joint.
  3. Remove the rubber bellows portion of the inner cable from the slit in the bracket.

NOTICE:

  • Do not remove the cable by pulling the outer casing.

TECH TIPS:

  • If it's difficult to remove the outer casing, insert a 2 mm hexagon wrench or #14 spoke into the pulley hole and turn the pulley to slacken the inner cable.

2. Replacing the Inner Cable

For REVOSHIFT shifter:

  1. Set the REVOSHIFT shifter to 1.
  2. Loosen the cover fixing screws and remove the cover.
  3. Remove the inner cable fixing bolt unit from the cassette joint pulley.
  4. Pass the inner cable from the hole in the winder unit, through the cable adjustment barrel, and into the cable guide groove. Pull the inner cable so the drum fits into the recess.
  5. Replace the cover and tighten the cover fixing screws to 0.1-0.2 N·m using screwdriver [#1].
REVOSHIFT inner cable replacement
Diagram showing the steps for replacing the inner cable in a REVOSHIFT shifter.

For SB-8S20-A:

  1. Set the REVOSHIFT shifter to 1.
  2. Loosen the cover fixing screws and remove the cover.
  3. Remove the inner cable fixing bolt unit from the cassette joint pulley.
  4. Pass the inner cable through the cable adjustment barrel hole, hook it into the pulley groove, and pull so the drum fits into the pulley hole.
  5. Replace the cover and tighten the cover fixing screws to 0.2-0.4 N·m using screwdriver [#1].

For SB-C3000-7:

  1. Set the REVOSHIFT shifter to 1.
  2. Loosen the cover fixing screws and remove the cover.
  3. Remove the inner cable mounting bolt unit from the cassette joint pulley.
  4. Pass the inner cable through the winder unit hole, cable adjustment barrel, and into the cable guide groove. Pull so the drum fits into the recess.
  5. Replace the cover and tighten the cover fixing screws to 0.1-0.2 N·m using screwdriver [#1].

For RAPIDFIRE PLUS shifter:

  1. Set the shifter to 1.
  2. Loosen and remove the inner hole cap.
  3. Remove the inner cable fixing bolt unit from the cassette joint pulley.
  4. Insert the inner cable into the winder unit groove, through the cable adjustment barrel hole, and pull so the drum fits into the recess.
RAPIDFIRE PLUS inner cable replacement
Diagram showing the steps for replacing the inner cable in a RAPIDFIRE PLUS shifter.

3. Replacement and Assembly of the Indicator Unit

Disassembly and assembly should only be carried out when removing or replacing the indicator unit.

Removal:

  1. Operate lever B and set it to 1.
  2. Loosen and remove the two cover fixing screws securing the indicator unit.
  3. Remove the indicator unit.

Installation:

  1. Check that the needle of the indicator is on the left side (positioned at 1).
  2. Install the indicator unit facing straight upward. Insert the axle of the pin plate into the hole in the winder unit.
  3. Secure the indicator unit with the two cover fixing screws. Tighten to 0.3-0.5 N·m using screwdriver [#2].
  4. Operate lever A and lever B, and check their operation. If incorrect, reinstall the indicator unit.

NOTICE:

  • Do not disassemble the indicator unit or the shifter unit, as this may result in malfunctions.

4. Oil Maintenance of the Internal Assembly

To maintain proper performance, lubricate the internal unit once a year from the start of use (or every 2,000 km if used frequently). More frequent maintenance is required under harsh conditions. Use SHIMANO internal geared hub grease or a lubrication kit.

  1. Fill the container with maintenance oil to a height of 95 mm.
  2. Immerse the internal unit in the oil from the left side until the oil reaches up to ring gear unit 1.
  3. Keep the internal unit immersed for approximately 90 seconds.
  4. Remove the internal unit from the oil.
  5. Let excess oil drain off for approximately 60 seconds.

TECH TIPS:

  • Maintenance oil is reusable. Refill as needed and store with the lid closed.

NOTICE:

  • After oil maintenance, apply Grease (Y04130100) to the ball retainers, snap ring, brake shoe, and pinion gears.

5. Reassembling the Hub

  1. Use the left-hand cone (or stop nut for coaster brake type) to adjust the hub so that the hub shell rotates smoothly with no excess play. Ensure the stop nut's non-protruding side faces up.
  2. Tighten the left-hand lock nut.

Tightening Torque for Left-Hand Lock Nut:

  • For disc brake, roller brake, or V-brake type: 24.5 to 29.4 N·m
  • For coaster brake or coaster brake (with disc brake) type: 17.7 to 24.5 N·m

Troubleshooting

PhenomenonCause (Internal Gear-Shifting Structure)Gear Positions Affected
Clicking felt in pedal when moving bicycle backward.Normal gear shifting operation (pawls and ratchet noise).All gear positions (7-speed, 8-speed).
Noise occurs when pedals rotate.Normal internal gear-shifting structure.All gear positions (7-speed), 2nd-7th (8-speed).
Noise occurs when bicycle is pushed backward.Normal internal gear-shifting structure.5th-8th (8-speed).
Hub makes noise/vibrations during gear shifting.Built-in mechanism supporting gear shifting.All gear positions (8-speed).
Gear-shifting feels different depending on gear position.Normal internal gear-shifting structure.All gear positions (7-speed, 8-speed, 5-speed).
Noise occurs when pedal rotation is stopped during riding.Normal internal gear-shifting structure.4th, 5th (8-speed, 5-speed).

General Notes:

  • The internal geared hub is not completely waterproof. Avoid water ingress and high-pressure washing to prevent rust.
  • Products are not guaranteed against natural wear and deterioration from normal use and aging.
  • For maximum performance, SHIMANO lubricants and maintenance products are highly recommended.

User Tips

  • Maintenance-Free Operation: The internal geared hub system is practically maintenance-free, making it a convenient choice for regular use.
  • Shifting While Stopped: A key advantage of internal geared hubs is the ability to change gears even when the bicycle is stopped, which is very practical for urban riding.
  • Cable Compatibility: Pay close attention to the cable installation kit. Some dust covers on cables may not fit certain kits, requiring modification or a different kit with a longer claw. Specialized cable clippers can be helpful.
  • Initial Adjustment: An initial "zero adjustment" might be necessary after installation, as the rotation can feel a bit stiff.
  • Check Sprocket Teeth: While not always critical, verify the sprocket teeth count matches your expectations, as sometimes a different size (e.g., 21T instead of 18T) might be included.

Warranty and Support

For warranty information, technical support, or to obtain a hardcopy of the User's Manual if you do not have internet access, please contact a SHIMANO distributor or any of the SHIMANO offices.

  • SHIMANO NORTH AMERICA BICYCLE, INC.
    One Holland, Irvine, California 92618, U.S.A.
    Phone: +1-949-951-5003
  • SHIMANO EUROPE B.V.
    High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
    Phone: +31-402-612222
  • SHIMANO INC.
    3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan

All manuals and technical documents are accessible online at https://si.shimano.com.

Please note that specifications are subject to change for improvement without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.