TKXEC Transistor Withstand Voltage Tester

Contents

TKXEC Transistor Withstand Voltage Tester User Manual

Model: Transistor Withstand Voltage Tester

1. Introduction

This portable voltage capability tester is designed to help you accurately determine the maximum voltage capacity of various electronic components. It is an essential tool for hobbyists and professionals working with MOS transistors, triodes, IGBTs, diodes, Zener diodes, and LED backlights. Its user-friendly interface, adjustable voltage and current outputs, and compact design make it convenient for a wide range of testing applications.

2. Safety Information

WARNING: This device generates high voltage (up to 2600V). Improper use can result in severe injury or death. Always follow safety precautions.

  • Always ensure the device is switched OFF before connecting or disconnecting components.
  • Never touch the test leads or the component under test when the device is powered ON and actively testing.
  • Use appropriate personal protective equipment (PPE), such as insulated gloves and safety glasses, when operating this tester.
  • Do not operate the device in wet conditions or with wet hands.
  • Keep the device away from children and unauthorized personnel.
  • If the device appears damaged or malfunctions, discontinue use immediately.
  • Ensure proper ventilation when operating.

3. Product Overview

The TKXEC Transistor Withstand Voltage Tester is a compact, handheld device featuring a digital display and intuitive controls.

3.1 Components

  • Tester Unit
  • Test Leads (Red and Black alligator clips)
  • Type-C USB Charging Cable (not explicitly listed but implied by Type-C port)

3.2 Controls and Indicators

Angled view of the TKXEC Transistor Withstand Voltage Tester showing the digital display, control knobs, and test lead connections.
Figure 1: Angled view of the tester with test leads and green terminal block.
  • Digital Display: Shows the measured voltage (up to 4 digits).
  • Voltage Adj. Knob (Yellow): Adjusts the output voltage from 110V to 2600V. Turn clockwise to increase, counter-clockwise to decrease.
  • Current Adj. Knob (Red): Adjusts the output current from 0.25mA to 3.4mA. Turn clockwise to increase, counter-clockwise to decrease.
  • Indicator Light (Red LED): Illuminates during testing.
  • START Button (Red): Initiates the voltage test.
  • ON/OFF Switch: Powers the device on or off.
  • 5V 1A TYPE-C Port: Used for charging the internal battery.

4. Setup

4.1 Charging the Device

The tester is equipped with a built-in 660mAh lithium battery. Before first use, or when the battery is low, charge the device using a standard 5V 1A Type-C charger.

The TKXEC Transistor Withstand Voltage Tester connected to a Type-C charging cable.
Figure 2: Tester connected to a Type-C charging cable.
  1. Locate the Type-C port on the side of the tester.
  2. Connect a Type-C USB cable to the port and the other end to a 5V 1A power source (e.g., a phone charger or computer USB port).
  3. The device will charge automatically. There is no explicit charging indicator mentioned, so monitor the device for any visual cues or charge for a sufficient period (e.g., 2-3 hours for a full charge).

4.2 Connecting Test Leads

The test leads are typically connected via a green terminal block at the top of the device.

  1. Ensure the tester is switched OFF.
  2. Connect the red test lead to the positive (+) terminal and the black test lead to the negative (-) terminal on the green terminal block.
  3. Ensure connections are secure.

5. Operating Instructions

5.1 General Testing Procedure

  1. Power On: Flip the ON/OFF switch to the 'ON' position. The digital display should illuminate, possibly showing '0000' or a previous reading.
  2. The TKXEC Transistor Withstand Voltage Tester with its digital display showing '0000', indicating it is powered on but not actively measuring.
    Figure 3: Tester powered on, showing '0000' on the display.
  3. Connect Component: Carefully connect the component to be tested to the alligator clips of the test leads. Ensure correct polarity if applicable (e.g., for diodes, LEDs).
  4. Adjust Current: Turn the Current Adj. knob to the desired current setting. Refer to section 5.2 for specific component recommendations.
  5. Adjust Voltage: Turn the Voltage Adj. knob to set the initial voltage. It is recommended to start with a lower voltage and gradually increase it.
  6. Start Test: Press the START button. The indicator light will illuminate, and the display will show the measured withstand voltage.
  7. Front view of the TKXEC Transistor Withstand Voltage Tester displaying '2700' with the red indicator light on, signifying an active test.
    Figure 4: Tester displaying '2700' with indicator light on during a test.
  8. Read Measurement: The digital display will show the maximum voltage the component can withstand at the set current.
  9. End Test: Release the START button to stop the test.
  10. Disconnect Component: Ensure the START button is not pressed and the indicator light is off before safely disconnecting the component.
  11. Power Off: Flip the ON/OFF switch to the 'OFF' position when finished.

5.2 Component-Specific Current Recommendations

  • MOS tubes, Transistors, Zener Diodes: It is recommended to adjust the Current Adj. knob to the minimum scale of 0.25mA. This helps prevent damage to sensitive components.
  • LED Backlight Boards: For testing LED backlight boards, it is recommended to adjust the Current Adj. knob to the maximum scale of 3.4mA to ensure sufficient current for illumination.

5.3 Testing Examples

Below are examples of various components being tested with the device:

The TKXEC Transistor Withstand Voltage Tester measuring a 1200V IGBT, displaying '1258'.
Figure 5: Measuring a 1200V IGBT, displaying 1258V.
The TKXEC Transistor Withstand Voltage Tester measuring a MUR460 Diode, displaying '0777'.
Figure 6: Measuring a MUR460 Diode, displaying 777V.
The TKXEC Transistor Withstand Voltage Tester measuring a 1000V Rectifier bridge, displaying '1454'.
Figure 7: Measuring a 1000V Rectifier bridge, displaying 1454V.
The TKXEC Transistor Withstand Voltage Tester measuring a 700V N-MOSFET, displaying '0780'.
Figure 8: Measuring a 700V N-MOSFET, displaying 780V.
The TKXEC Transistor Withstand Voltage Tester measuring an 18V Stabilizing tube, displaying '0018'.
Figure 9: Measuring an 18V Stabilizing tube, displaying 18V.
The TKXEC Transistor Withstand Voltage Tester measuring a 30V LED panel, displaying '0030'.
Figure 10: Measuring a 30V LED panel, displaying 30V.
The TKXEC Transistor Withstand Voltage Tester measuring a 330UF/63V Capacitance, displaying '0080'.
Figure 11: Measuring a 330UF/63V Capacitance, displaying 80V.
The TKXEC Transistor Withstand Voltage Tester measuring a Sub-sensitive resistor 10471K, displaying '0475'.
Figure 12: Measuring a Sub-sensitive resistor 10471K, displaying 475V.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the device. Do not use abrasive cleaners or solvents.
  • Storage: Store the tester in a cool, dry place away from direct sunlight and extreme temperatures.
  • Battery Care: To prolong battery life, avoid fully discharging the battery frequently. Recharge the device regularly, especially if it will be stored for an extended period.
  • Test Leads: Inspect test leads for any signs of wear or damage before each use. Replace damaged leads immediately.

7. Troubleshooting

ProblemPossible CauseSolution
Device does not power on.Battery is discharged.Charge the device using the Type-C port.
No reading on display during test.Component not connected properly.
START button not pressed.
Voltage/Current knobs set too low.
Ensure secure connection.
Press and hold the START button.
Adjust Voltage/Current knobs to appropriate levels.
Inaccurate readings.Incorrect current setting for component type.
Damaged test leads.
Refer to section 5.2 for recommended current settings.
Inspect and replace test leads if damaged.
Indicator light does not turn on.START button not pressed.
Device malfunction.
Ensure START button is pressed. If issue persists, contact support.

8. Specifications

FeatureSpecification
MaterialABS
Output VoltageDC 110V ~ 2600V (Adjustable)
Output Current0.25mA ~ 3.4mA (Adjustable)
Battery1 * Lithium battery, 660mAh (Included)
Recharge PortTYPE-C (5V 1A)
Package Size130 * 80 * 40mm / 5.1 * 3.1 * 1.6in
Package Weight175g / 6.2ounce
DIY SuppliesElectrical
CertificationNone
OriginMainland China

9. User Tips

  • Start Low, Go Slow: When testing unknown components, always start with the Voltage Adj. knob set to its minimum and gradually increase it while observing the display. This helps prevent accidental damage to the component.
  • Component Polarity: Pay close attention to the polarity of components like diodes and LEDs. Incorrect connection can lead to inaccurate readings or component damage.
  • Stable Surface: Always place the tester on a stable, non-conductive surface during operation to prevent accidental contact with high voltage.
  • Clean Connections: Ensure the alligator clips make good, clean contact with the component leads for accurate measurements.

10. Warranty & Support

For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.