diymore BMS 10S 36V 42V

Contents

BMS 10S 36/42V Lithium Battery Protection Board User Manual

Model: BMS 10S 36V 42V | Brand: diymore

1. Introduction

This manual provides essential information for the safe and effective use of your diymore BMS (Battery Management System) 10S 36/42V Lithium Battery Protection Board. This board is designed to protect 10-series lithium-ion battery packs, ensuring their longevity and safe operation by managing charging, discharging, and balancing.

2. Setup and Wiring Instructions

Proper wiring is crucial for the correct function and safety of the BMS and your battery pack. Please follow these steps carefully.

2.1 General Precautions

  • Always perform wiring in an anti-static environment.
  • Ensure the board does not come into contact with water or excessive moisture.
  • Avoid physical impact or extrusion of the protective plate during installation and use.
  • Prevent soldering tin, conductive objects, or leads from falling onto, sticking to, or contacting the protective plate.
  • Ensure all welding points are firm, reliable, and have good electrical conductivity.
  • Keep wiring smooth and short to minimize resistance and potential hazards.

2.2 Wiring Steps

  1. Connect the Collection Flat Cable: Connect the flat cable to each section of the battery pack. Ensure the effective connection of the flat cable and that the potential of the flat cable plug end increases or decreases in sequence. The potential sequence must be consistent with that of the socket on the protection board (one-to-one correspondence).
  2. Weld B-lead to Battery Pack: Weld the B-lead of the protection plate to the total negative (B-) terminal of the battery pack.
  3. Connect Flat Cable Plug: Connect the plug of the flat cable to the socket on the protection plate. Ensure the plug and socket are securely connected, and no live objects or leads contact the protection board. Implement fixing measures to prevent accidental disconnection.
  4. Connect Charging Interface: Connect B+ and C- (or P-) to the positive and negative electrodes of the charging/discharging interface respectively. Ensure other leads are isolated during welding and wiring to prevent short circuits.
Wiring Diagram for BMS 10S

Figure 1: BMS 10S Wiring Diagram (Homojunction/Same Port)
This diagram illustrates the connections for the battery cells (B- to B+), the balance leads (B0 to B6+), and the main charge/discharge terminals (P- and C-).

BMS Board Internal Components

Figure 2: BMS Board Internal Components
Shows the layout of 4 imported power MOS tubes, the professional lithium battery control and protection IC, and the NTC temperature sensor.

BMS Board Back View with Insulating Paper and Sensor

Figure 3: BMS Board Back View
Illustrates the barley paper with insulating back, the NTC temperature sensor, and the arrangement of sampling cables for each battery pack.

2.3 Verification

After wiring, test the battery pack voltage at the dynamic interface and charging interface. Ensure it is consistent with the battery pack voltage, and that the polarity and wiring positions are correct.

3. Operating Principles

The BMS 10S 36/42V board provides comprehensive protection for your lithium battery pack:

  • Overcharge Protection: Prevents cells from being charged beyond their safe voltage limit (4.25V per cell), extending battery life and preventing damage.
  • Overdischarge Protection: Stops discharge when cell voltage drops below a safe threshold (2.6V per cell), preventing irreversible damage to the battery.
  • Overcurrent Protection: Limits the current drawn from the battery during discharge to prevent damage to cells and connected devices.
  • Short Circuit Protection: Immediately cuts off power in case of a short circuit to prevent damage and fire hazards.
  • Temperature Protection: Monitors battery temperature. It will stop discharge if the temperature exceeds 75°C and prevent charging if the temperature drops below -7°C, ensuring safe operation within optimal temperature ranges.
  • Equalizing Charging Function: Balances the voltage of individual cells within the pack during charging (equalizing voltage is 4.2V), ensuring all cells are charged uniformly and prolonging the overall battery pack life.

4. Maintenance

  • Keep Dry and Clean: Ensure the BMS board remains dry and free from dust and debris.
  • Avoid Physical Stress: Do not subject the board to impact, bending, or excessive pressure.
  • Regular Inspection: Periodically check all wiring connections for looseness or corrosion.
  • Anti-static Handling: Always observe anti-static precautions when handling the board, especially during any re-wiring or inspection.

5. Troubleshooting

If you encounter issues, consider the following common problems and solutions:

  • Battery Not Charging:
    - Check if the charger is functioning correctly.
    - Verify all charging connections (B+, C-) are secure and correctly polarized.
    - Ensure no overcharge protection has been triggered (unlikely if not charging).
    - Check if the temperature is below -7°C, which would prevent charging.
  • Battery Not Discharging/No Output:
    - Verify all discharge connections (B-, P-) are secure and correctly polarized.
    - Check if overdischarge protection has been triggered (battery voltage too low).
    - Check for short circuits in the load or wiring.
    - Ensure the temperature is not above 75°C, which would prevent discharge.
  • Battery Imbalance:
    - Ensure the equalizing function is active during charging. This process takes time.
    - Verify all balance leads are correctly connected to each cell.
  • BMS Overheating:
    - Ensure the maximum continuous working current is not exceeded.
    - Check for any short circuits or excessive load.
    - Verify proper ventilation around the BMS and battery pack.
  • General Malfunction:
    - Re-check all wiring according to the diagram.
    - Ensure no short circuits occurred during wiring (e.g., P+P short circuit can damage MOS tubes).
    - Confirm the battery pack voltage and cell count match the BMS specifications.

6. Specifications

FeatureSpecification
Model10 series 36V/30A (same port)
Applicable Voltage & Power36V < 1000W
Applicable Battery Type3.7V Ternary Lithium Battery (Lithium Cobaltate Manganate)
Maximum Working Current30A MAX
Maximum Continuous Working Current20A MAX
Overdischarge Protection Voltage2.6V per cell
Overcharge Protection Voltage4.25V per cell
Charging Current20A MAX
Equalizing Charging Voltage4.2V
Temperature Protection (Discharge)High temperature 75°C
Temperature Protection (Charge)Low temperature -7°C
Application FieldsElectric vehicle, swing car, electric power assisted vehicle, scooter, inverter, etc.
BMS Board Dimensions and Weight

Figure 4: BMS Board Dimensions and Weight
Dimensions: 6.3cm (2.48in) x 3cm (1.18in). Weight: 24.6g.

7. User Tips

  • This BMS is suitable for various applications including electric bikes, bicycles, scooters, and other electric power assisted vehicles.
  • Always ensure a dustproof and waterproof environment for the BMS.
  • Properly configure the size of the nickel plate used for battery connections to match current requirements.
  • Avoid repeatedly short-circuiting P+P, as this can cause circuit voltage spikes and damage the MOS tubes.
  • Keep the protective plate dry; water contact can easily damage it.

8. Warranty and Support

For warranty information, please refer to the terms provided by your seller at the time of purchase. If you encounter any issues or require technical assistance, please contact the official diymore support channel or your point of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.