Taidacent wireless power supply module 001-34

Contents

Taidacent 12V Wireless Power Supply Module User Manual

Model: wireless power supply module 001-34

1. Introduction

This manual provides instructions for the Taidacent 12V Input, 12V 500mA Output Contactless Wireless Charging Electromagnetic Induction Charger Module. This module is designed for applications requiring wireless power transfer, offering a convenient and efficient solution for various electronic projects.

Taidacent Wireless Power Supply Module Overview
Figure 1: Overview of the Taidacent Wireless Power Supply Module, showing both the transmitter and receiver units with their respective input/output wires.

2. Package Contents

  • 1x Wireless Power Transmission (Launch) Module with Coil
  • 1x Wireless Power Reception (Receive) Module with Coil and Voltage Stabilizer Board

3. Specifications

FeatureSpecification
Input Voltage12V DC
Launch Module Size16mm (L) x 12mm (W) x 2.5mm (T)
Transmitting CoilOuter diameter 30mm, Inductance 5.6uH (L105)
Receiving Voltage Stabilizer Board Size24mm (L) x 10mm (W)
Receiving CoilOuter diameter 30mm, Inductance 5.6uH (L105)
Output (at 4mm distance)12V DC, 600mA
Output (at 5mm distance)12V DC, 500mA
Minimum Operating DistanceGreater than 4mm
Accessory TypeCharger Accessories
OriginMainland China
Coil dimensions and inductance
Figure 2: Close-up of the transmitting and receiving coils, indicating their 30mm diameter and 5.6uH inductance.

4. Setup Instructions

Follow these steps to set up your wireless power supply module:

  1. Identify Modules: Distinguish between the Launch (Transmitter) module and the Receive module. The Launch module typically has input wires, and the Receive module has output wires, often with a voltage stabilizer board.
Launch and Receive Module Identification
Figure 3: Illustration clearly labeling the 'Launch module' (transmitter) and 'Receive module' (receiver) with their respective 12V input and 12V output connections.
  1. Connect Power to Launch Module: Connect a 12V DC power source to the Launch module. The red wire is for positive (+) and the black wire is for negative (-). Ensure correct polarity.
  2. Connect Load to Receive Module: Connect your 12V DC load to the Receive module's output wires. The red wire is for positive (+) and the black wire is for negative (-).
  3. Position Coils: Place the transmitting coil and receiving coil in close proximity, ensuring they are aligned as much as possible. The minimum operating distance is greater than 4mm. Optimal performance is typically achieved with a small air gap (e.g., 4-5mm).
  4. Wiring Diagram Reference: For detailed circuit connections, refer to the provided schematic.
Wireless Power Module Circuit Diagram
Figure 4: Detailed circuit diagram for the wireless power supply module, showing the transmitter (top) and receiver (bottom) sections with component values and IC pinouts. The transmitter section includes IC1 (XKT-001) and IC2 (XKT-335*2) with a 12V VDD input. The receiver section includes IC1 (T3168) providing a 5V/500mA output, with various diodes, capacitors, and resistors.

5. Operating Instructions

  1. After completing the setup as described above, apply 12V DC power to the Launch module.
  2. Ensure the transmitting and receiving coils are within the effective operating distance (greater than 4mm).
  3. The Receive module will then output 12V DC to your connected load.
  4. Monitor the load to ensure it is receiving power correctly.

6. Maintenance

  • Keep the modules dry and away from moisture to prevent damage.
  • Avoid exposing the modules to extreme temperatures.
  • Handle the coils and circuit boards with care to prevent physical damage.
  • Do not attempt to modify the circuit, as this may void any implied warranty and could damage the module.

7. Troubleshooting

  • No Output Power:
    • Check if the 12V input power is correctly connected to the Launch module and is active.
    • Verify the polarity of all connections (red to +, black to -).
    • Ensure the transmitting and receiving coils are properly aligned and within the effective operating distance (minimum 4mm).
    • Check for any visible damage to the coils or circuit boards.
  • Low Output Power:
    • Ensure the distance between the coils is optimal (e.g., 4-5mm). Increased distance will reduce output power.
    • Verify that the load does not exceed the module's maximum output current (500mA at 5mm, 600mA at 4mm).

8. User Tips

No specific user tips are available for this product at this time.

9. Warranty and Support

For any issues, technical support, or warranty inquiries, please contact the seller directly through your purchase platform. Please provide your order details when contacting support.

© 2023 Taidacent. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.