Safety Information
WARNING: BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING SAFETY INSTRUCTIONS. FAILURE TO FOLLOW WARNINGS COULD RESULT IN DEATH OR SERIOUS INJURY.
General Safety Rules
- Wear Safety Glasses or Goggles: Danger to the eyes always exists due to the possibility of dust being blown up by exhausted air or a fastener flying up due to improper handling. Always wear safety glasses or goggles. The employer and/or user must ensure proper eye protection is worn. Non-side shielded spectacles and face shields alone do not provide adequate protection.
- Ear Protection May Be Required: Working conditions may include exposure to high noise levels leading to hearing damage. Ensure necessary hearing protection is provided and used by the operator and others in the work area.
- Do Not Use Any Power Source Except an Air Compressor: The tool is designed for compressed air only. Do not operate with high-pressure gas or combustible gases (e.g., Oxygen, acetylene) due to explosion risk.
- Operate Within Proper Air Pressure Range: The tool operates within 70-100 psi (5-7 bar). Adjust pressure to the fastener type. Never operate above 120 psi (8.3 bar).
- Do Not Operate Near Flammable Substances: Never use the tool near flammable substances (e.g., thinner, gasoline). Volatile fumes can be drawn into the compressor, compressed with air, and explode.
- Do Not Use a Wrong Fitting: The connector on the tool must not hold pressure when air supply is disconnected. A wrong fitting can leave the tool charged with air, allowing it to drive a fastener after disconnection, potentially causing injury.
- Disconnect Air Supply and Empty Magazine When Not in Use: Always disconnect the air supply and empty the magazine when operation is complete, suspended, unattended, moving to a different work area, adjusting, disassembling, repairing, or clearing a jammed fastener.
- Inspect Screw Tightness: Loose or improperly installed screws/bolts can cause accidents and tool damage. Inspect all screws and bolts are tight before operation.
- Do Not Touch the Trigger Unless Intending to Drive a Fastener: Never touch the trigger when the air supply is connected unless you intend to drive a fastener. Avoid walking around with the tool with the trigger pulled.
- Never Point the Discharge Outlet Toward Yourself and Personnel: Pointing the discharge outlet toward people can cause serious accidents if misfiring occurs. Ensure the discharge outlet is not pointed toward people during connection, disconnection, or loading.
- Use Specified Fasteners: Using fasteners other than specified types will cause tool malfunction. Use only specified fasteners.
- Place the Discharge Outlet to the Work Properly: Failure to properly place the discharge outlet of the nose can result in a fastener flying up, which is extremely dangerous.
- Keep Hands and Body Away from the Discharge Outlet: Never place hands or any body part in the fastener discharge area when loading or using the tool.
- Do Not Drive Fasteners Close to the Edge/Corner or on Thin Material: The workpiece may split, and the fastener could fly and hit someone.
- Do Not Drive Fasteners on Top of Other Fasteners: This may cause deflection and injury.
- Removing Fasteners After Operation: If fasteners are left in the magazine, there is a danger of serious accidents if the tool is handled carelessly or when connecting the air. Always remove fasteners after operation.
- Check Operation of the Contact Trip Mechanism: If using a contact trip type tool, frequently check its operation. Do not use if the trip is not working correctly, as accidental driving may result.
- When Using the Tool Outside or in Elevated Places: When fastening roofs or slanted surfaces, start from the lower part and work upwards. Fastening backward is dangerous. Secure the hose close to the work area to prevent accidents from being pulled or caught.
- Never Use the Tool if Any Portion of the Tool Controls is Inoperable: This includes the trigger or contact arm.
- Never Actuate the Tool into Free Space: This avoids hazards from free-flying fasteners and excessive strain on the tool.
- Always Assume the Tool Contains Fasteners.
- Do Not Use on Scaffolding or Ladders: The tool should not be used for specific applications like changing driving locations on scaffolding, stairs, ladders, roof laths, closing boxes, or fitting transportation safety systems.
Product Overview
The Reilyn 21GA Air Stapler 8016 is a pneumatic crown stapler designed for various applications including upholstery, furniture, and cabinetry. It features a durable construction and efficient stapling mechanism.

Figure 1: Reilyn 21GA Air Stapler 8016
Parts Identification

Figure 2: Labeled Parts of the Stapler
- Top Cap: Knurled adjustment knob.
- Handle Grip: Textured rubber sleeve for comfortable handling.
- Trigger: Operates the stapler, includes a safety lever.
- Air Inlet: Rear inlet with quick coupler for air hose connection.
- Magazine: Holds up to 150 staples, features a steel rail.
- Contact Nose: Contact trip nose for precise stapling.
Main Applications

Figure 3: Common Applications
- Upholstery
- Furniture assembly
- Cabinetry
- Picture frames
- Wardrobe decoration
- Sofa manufacturing
- Shoe making
- Fabric stretching and fixing
- Thin material joining and fixing
Specifications

Figure 4: Detailed Specifications
| Feature | Specification |
|---|---|
| Model Number | 8016 |
| Nail/Staple Gauge | 21 GA |
| Nail/Staple Length | 6-16 mm (1/4"-5/8") |
| Crown Width | 12.7 mm |
| Wire Dimensions | 0.9 x 0.7 mm |
| Magazine Capacity | 150 pcs |
| Net Weight | 0.9 kg |
| Package Weight | 1 kg |
| Dimensions (L x H) | 215 x 165 mm |
| Air Inlet | 1/4" N.P.T. |
| Operating Pressure | 60-100 PSI (4-7 bar) |
| Grip Material | Rubber |
| Certification | CE |
| Origin | Mainland China |

Figure 5: Compatible Staple Dimensions
Setup
Air Supply Connection
The Reilyn 21GA Air Stapler operates on compressed air. Ensure your air compressor is suitable and provides clean, dry, regulated air.
- Air Compressor: Use only clean, dry, regulated compressed air. Never use oxygen or other bottled gases.
- Air Hose: The air hose must have a minimum working pressure rating of 180 psi, a minimum ID of 1/4" (ISO 7-1), and a maximum length of 17 feet (5 meters). It should contain a quick-disconnect fitting.
- Fittings: Install a female coupler to the air hose. This coupler will connect to the quick release on the tool.
- Filter-Regulator-Lubricator: These units provide optimum conditions for the nailer and extend its life. They should always be used. The filter removes moisture and dirt, and the regulator controls operating pressure. Inspect the regulator before operation.

Figure 6: Air Supply Setup Diagram
Lubrication
Before each use, or if an inline lubricator is not used, add a few drops of oil to the nailer inlet. This lubricates internal parts and prevents wear and corrosion.
Video 1: Product demonstration including lubrication and air connection.
Operation
Nail Loading Procedure

Figure 7: Nail Loading Steps
- Disconnect the air hose.
- Press the LATCH (200070) to open the DOOR (210050), then open the MAGAZINE COVER (420190).
- Adjust the height of the NAIL SUPPORT (420210) according to the nail length.
- Fix the first nail in the groove on the FEED PAWL (210080).
- Close the MAGAZINE COVER (420190), then close the DOOR (210050).
- Connect the air hose.
Test Operation
- Adjust the air pressure to 70 psi (5 bar) and connect the air supply.
- Without touching the trigger, depress the contact arm against the workpiece. Pull the trigger. (The tool should fire the fastener.)
- With the tool off the workpiece, pull the trigger. Then depress the contact arm against the workpiece. (The tool must fire the fastener.)
- Adjust the air pressure to the lowest possible setting according to the fastener diameter, length, and workpiece hardness.
Product Features
- Strong Penetration and Smooth Nail Delivery: Designed for efficient and consistent performance.
- Spring Buffer Design: Prevents accidental firing.
- Applicable Gas Pipe: Outer diameter 11mm.
Maintenance and Inspection
Always refer to the Safety Information section before performing any maintenance.
Service and Repairs
All quality tools eventually require servicing or part replacement. It is recommended that these operations be performed by a professional technician.
WARNING: Disconnect the air hose and remove nails from the nailer when performing maintenance, inspection, or clearing a jam.
Inspecting the Magazine
- Disconnect the air hose.
- Clean the magazine to remove any accumulated dust.
- Lubricate the nailer rail with nailer lubricant.
Clearing a Jam
To remove a jammed nail:
- Disconnect the air hose.
- Remove all nails from the magazine.
- Remove the jammed nail with a slotted head screwdriver.
- In case of frequent jams, contact an authorized service center.
Periodic Maintenance
- Check that the piston bumper is operating normally. A damaged bumper can cause damage to other components.
- Check O-rings for wear or damage. Damaged O-rings can affect overall performance.
- Ensure all screws are secure. Loose screws can affect overall performance.
- When repairing, ensure internal parts are clean and lubricated.
Storing
- For extended periods of non-use, apply a thin coat of lubricant to steel parts to prevent rust.
- Store the nailer in a warm and dry place. Do not store in a cold weather environment.
Troubleshooting
- Tool not firing: Ensure air supply is connected, pressure is within the operating range (60-100 PSI), and the magazine contains staples. Check for jammed nails.
- Jammed nails: Follow the 'Clearing a Jam' procedure in the Maintenance section. Frequent jams may indicate an issue with staple type or tool malfunction, requiring professional service.
- Air leaks: Check all connections for tightness. Ensure O-rings are not worn or damaged. If leaks persist, professional inspection is recommended.
- Staples not fully driven: Adjust air pressure within the recommended range (60-100 PSI). Ensure correct staple length and type for the material.
User Tips
- Safety Mechanism: Be aware that this model may not have an external safety mechanism that prevents free firing. Always handle with extreme caution and keep the trigger clear when not actively stapling.
- Lubrication Oil: An oil bottle for lubrication is not included in the package. Ensure you acquire appropriate pneumatic tool oil separately for regular maintenance.
- Staple Compatibility: Always use 21GA staples with a 12.7mm crown width and lengths between 6-16mm (1/4"-5/8") for optimal performance and to prevent jams.
Frequently Asked Questions
- Q: Which staples should I buy for this stapler?
- A: You should use 21GA staples with a crown width of 12.7mm and lengths ranging from 6mm to 16mm (1/4"-5/8").
- Q: What type of air compressor is compatible with this stapler?
- A: Any standard air compressor capable of providing a regulated air pressure between 60-100 PSI (4-7 bar) is compatible. Ensure it delivers clean, dry air.
Warranty and Support
For detailed warranty information and support, please refer to the official product documentation. A comprehensive user manual in PDF format is available for download:
For further assistance or inquiries, please contact the seller or an authorized service center.