Vehicleader Winch Solenoid Relay Controller 500A

Contents

12V/24V Winch Solenoid Relay Controller User Manual

Model: Winch Solenoid Relay Controller 500A

1. Product Overview

The Vehicleader 12V/24V Winch Solenoid Relay Controller is a robust and reliable solution for controlling winches up to 17,000 lbs loading capacity. Featuring a solid construction with a 500A sealed DC solenoid, it offers consistent performance and high corrosion resistance, making it ideal for various outdoor applications including trucks, ATVs, 4x4s, and trailers.

Front view of the 12V/24V Winch Solenoid Relay Controller

Figure 1: Front view of the Winch Solenoid Relay Controller

Top view of the 12V/24V Winch Solenoid Relay Controller showing terminals

Figure 2: Top view showing the terminals of the controller

Winch Solenoid Relay Controller held in hand for size comparison

Figure 3: Controller size comparison when held in hand

2. Safety Warnings

  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Always disconnect power before performing any maintenance or installation.
  • Verify the correct voltage (12V or 24V) matches your winch system to avoid damage.
  • Do not exceed the maximum loading capacity of 17,000 lbs.
  • Keep the wireless remote controls away from water and extreme temperatures.

3. Setup and Installation

This section provides general guidance for installing your winch solenoid relay controller. Always refer to your winch's specific wiring instructions for detailed connections.

3.1 Component Identification

Winch solenoid relay controller with wireless remote controls and wiring components

Figure 4: Winch Solenoid Relay Controller and Remote System Components

3.2 Wiring Diagram

The following diagram illustrates a typical wiring setup for the winch solenoid relay controller. Ensure all connections are tight and properly insulated.

Detailed wiring diagram for WINCH-IT Contactor, showing connections to battery, motor, wireless remote, and wired switch

Figure 5: Wiring Diagram for Winch Contactor. Note: Wire colors may vary depending on the manufacturer.

  • Battery Connections: Connect the main power cables (12V/24V live and neutral) from your battery to the appropriate terminals on the contactor.
  • Motor Connections: Connect the motor's power cables to the contactor terminals labeled for motor input/output.
  • Control Wires: The yellow and green wires from the controllers provide positive feeds and control direction. For controllers that switch negative, feed positive to the center terminal.
  • Wireless Remote Receiver: Connect the receiver unit to the contactor using the provided wiring harness.
  • Wired Switch (Optional): If using a wired switch, connect it according to the diagram.

3.3 Video Guide

Watch this video for a visual demonstration of the product components and basic connections.

Video 1: Product demonstration and component overview.

4. Operating Instructions

The winch solenoid relay controller can be operated using the provided wireless remote controls.

4.1 Wireless Remote Control

  • Power Switch: Locate the ON/OFF power switch on the side of the remote control. Turn it ON before use and OFF when not in use to conserve battery life.
  • IN Button: Press the 'IN' button to retract the winch cable.
  • OUT Button: Press the 'OUT' button to extend the winch cable.
  • Indicator Light: A small LED light on the remote will illuminate when a button is pressed, indicating signal transmission.

5. Maintenance

  • Regular Inspection: Periodically check all electrical connections for tightness and signs of corrosion. Clean terminals as needed.
  • Cable Condition: Inspect the wiring for any fraying, cuts, or damage. Replace damaged cables immediately.
  • Housing Integrity: Ensure the solenoid housing is free from cracks or damage that could compromise its sealed nature.
  • Remote Control: Keep the remote controls clean and dry. Replace batteries as necessary.

6. Troubleshooting

  • Winch Not Responding:
    • Check if the remote control's power switch is ON.
    • Verify battery connections to the solenoid and the winch motor.
    • Ensure the vehicle's battery has sufficient charge.
    • Check for loose or corroded wiring connections.
  • Intermittent Operation:
    • Inspect for loose connections at the solenoid terminals or the remote receiver.
    • Check for interference with the wireless signal (if applicable).
    • Ensure the solenoid is not overheating (though unlikely with normal use).
  • Solenoid Clicking but Winch Not Moving:
    • This often indicates insufficient power reaching the winch motor. Check battery voltage under load.
    • Inspect heavy gauge cables for damage or poor connections.

7. Specifications

Dimensional drawing of the winch solenoid relay controller with measurements in mm and inches

Figure 6: Dimensional drawing of the Winch Solenoid Relay Controller

FeatureSpecification
Product TypeSwitches and accessories (Car Relays)
Model Namevehicle electric winch relay
OEM NO.Solenoid Relay Contactor Switch
Loading Current500A (Stable)
Coil Rated Voltage6-110V DC
Operating Power15W
Contact Circuit Voltage & Loading Current80V DC Max, 250V AC 500A
Mechanical Life100,000 Operations
Electrical Life50,000 Operations
Environment Temperature-40°C to 85°C
Frequency10Hz-200Hz
Acceleration=3.5g
Speed60-100 per minute
Operation RegulationContinuous
Winch CapacityUp to 17,000 lbs
Dimensions (L x W x H)10cm x 5.3cm x 8.5cm (approx. 3.94in x 2.09in x 3.35in)
Item Weight800g
MaterialMETAL & PLASTIC
ColourBlack
External Testing CertificationCE
OriginMainland China

8. User Tips

  • Voltage Selection: This controller supports both 12V and 24V systems. Always ensure you select the correct voltage variant (12V or 24V) that matches your vehicle's electrical system and winch requirements.
  • Pre-Installation Check: Before final installation, perform a quick test of the controller and remote functionality to ensure all components are working as expected.
  • Cable Management: Route all wiring carefully, avoiding sharp edges, moving parts, and heat sources. Use cable ties to secure wiring and prevent accidental disconnections.

9. Warranty and Support

For any questions, concerns, or technical assistance regarding your Winch Solenoid Relay Controller, please contact customer service. Our support team is available to help you with troubleshooting and product-related inquiries.

This product is designed for durability and reliability. In case of any issues, please reach out to us for support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.