Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your MatSee Plus Tuya Smart Life WiFi Energy Meter 80A. This device allows you to monitor electricity consumption (KWh), voltage, current, and power in real-time via the Tuya Smart or Smart Life mobile application. It is designed for easy, non-invasive installation using a current transformer (CT) clamp.
Safety Information
- Always disconnect power to the circuit before attempting any installation or wiring to prevent electric shock.
- Installation should be performed by a qualified electrician if you are unsure about electrical wiring.
- Do not exceed the rated current (80A) or voltage (100-240V AC) of the device.
- Ensure all connections are secure and properly insulated.
- The current transformer (CT) clamp is designed for non-invasive measurement. Do not attempt to connect it directly to live terminals.
- Keep the device away from water, moisture, and extreme temperatures.
Package Contents
- 1 x Tuya Smart Life WiFi Energy Meter Module
- 1 x Current Transformer (CT) Clamp (0.2-80A)
Specifications
| Feature | Specification |
|---|---|
| Rated Voltage | 100-240V AC 50/60Hz |
| Measurable Current Range | 0.2A - 80A |
| Communication Method | Wi-Fi (2.4GHZ) |
| App Name | Tuya Smart, Smart Life |
| Compatibility | All Compatible |
| State of Assembly | Ready-to-Go |
| Certification | CE, RoHS |
| Ambient Temperature Range | -10°C ~ 55°C |
| CT Clamp Diameter | Φ10mm |
| CT Cable Length | 0.7m |
| Module Dimensions | 50mm x 46mm |
Setup
1. Physical Installation
The energy meter module is designed for 35mm DIN rail mounting. Follow the wiring diagram carefully:
- Connect the Live (L) and Neutral (N) wires of your power supply to the corresponding L and N terminals on the meter module.
- Connect the S1 and S2 wires from the Current Transformer (CT) clamp to the S1 and S2 terminals on the meter module.
- Place the CT clamp around the live wire of the electrical load you wish to monitor. Ensure only one wire (either live or neutral, but not both) passes through the clamp for accurate measurement. The clamp is designed for non-invasive measurement, so there is no need to cut or alter your existing wiring.



2. App Installation
Download the 'Tuya Smart' or 'Smart Life' app from your smartphone's app store (available for iOS and Android).
3. Device Pairing
- Ensure the energy meter module is powered on. The indicator light should be flashing, indicating it's in pairing mode.
- Open the 'Tuya Smart' or 'Smart Life' app on your smartphone.
- Tap 'Add Device' (usually a '+' icon) and select the appropriate device type (e.g., 'Smart Energy Meter' or 'Electricity Meter').
- Follow the in-app instructions to connect the device to your 2.4GHz Wi-Fi network. You will need to enter your Wi-Fi password.
- Once successfully added, the device will appear in your app's device list.
Operating Instructions
1. Real-time Monitoring
Once connected, open the device interface in the Tuya Smart/Smart Life app to view real-time electrical parameters:
- Voltage (V): Displays the current line voltage.
- Current (A): Shows the instantaneous current flowing through the monitored circuit.
- Power (W): Indicates the real-time power consumption of the connected load.

2. Electricity Statistics
The app provides comprehensive historical data for electricity consumption:
- Hourly Elec. (KWh)
- Today Elec. (KWh)
- Monthly Elec. (KWh)
- Yearly Elec. (KWh)
- Total Elec. (KWh)

3. Power Usage Percentage Monitoring
You can set a maximum power value in the app. The device will then display the current power usage as a percentage of this set maximum, helping you visualize load relative to a threshold.

4. Automation and Scene Creation
Leverage the smart features of the Tuya Smart/Smart Life app to create custom automation rules (scenes):
- Conditional Actions: Set up 'If/Then' rules. For example, "If the measured power or current exceeds a set value, then trigger another Tuya-compatible smart device (e.g., turn off a smart plug)."
- Notifications: Configure the device to send alerts to your smartphone based on specific conditions, such as current reaching 0mA (indicating a device has turned off) or exceeding a power threshold.


User Tips
- Minimum Current Display: The app may not display data for very low currents. Ensure the measured current is at least 0.1A; values below 0.05A might not be shown.
- Power Factor: For accurate power readings, understand that real power (Watts) is calculated as Voltage × Current × Power Factor (cos(Φ)). The device accounts for this, providing real power consumption.
- Unidirectional Measurement: This specific energy meter model is designed to measure consumed power only (positive data). It is not a bidirectional meter and will not display negative power values for energy fed back to the grid (e.g., from solar panels).
- Wi-Fi Range: If the device is located far from your Wi-Fi router, consider using a Wi-Fi repeater to ensure a stable connection and reliable data transmission.
Troubleshooting
- App shows 'Device shutdown': If the app indicates 'Device shutdown' even after successful pairing, ensure that the CT clamp is correctly installed around a single live wire of an active load, and that the load is drawing current. The meter requires current flow to register as 'working'.
- Incorrect Power Readings: If the displayed power (W) seems inaccurate, verify that the CT clamp is properly installed around only one conductor (live wire) and not both live and neutral. Also, remember that real power considers the power factor, so a simple V*A calculation might not match.
- Device not pairing: Check that your Wi-Fi network is 2.4GHz (5GHz networks are not supported). Ensure the device's indicator light is flashing rapidly, indicating pairing mode. If not, try resetting the device (refer to the device's specific reset procedure, usually a long press on a button) and re-attempt pairing. Ensure your phone is connected to the same 2.4GHz Wi-Fi network during pairing.
- No data displayed for low current: The app has a minimum threshold for displaying current. If the measured current is below 0.1A (specifically, less than 0.05A), no data may be shown.
- No negative power readings for solar: This meter is designed for consumption monitoring only. It will not show negative values for energy generated by solar panels and fed back into the grid. If you require bidirectional measurement, a different product is needed.
Maintenance
- Keep the device clean and dry. Use a soft, dry cloth for cleaning.
- Avoid exposing the device to direct sunlight, extreme temperatures, or high humidity.
- Do not attempt to open, disassemble, or repair the device yourself, as this will void the warranty and could pose a safety risk.
Warranty & Support
MatSee Plus guarantees the quality of its products. Every unit is tested before delivery. For any technical assistance, troubleshooting, or warranty-related inquiries, please contact the seller directly. You can reach customer service via email at sophie@matseeplus.com.