yuyi 3-929080-5 3-1355470-1 A0245459926 A2215450228

Contents

2 Pin Auto Connector Wire Harness Plug Instruction Manual

Model: 3-929080-5, 3-1355470-1, A0245459926, A2215450228

1. Introduction

This manual provides essential information for the safe and effective use of your yuyi 2 Pin Auto Connector Wire Harness Plug. This product is designed for automotive applications, such as car ambient lights and welcome lights. Please read all instructions carefully before installation and use.

2. Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Non-professionals should not use this product for installation or repair.
  • Do not use this product for purposes other than its intended automotive electrical connection use.
  • Inspect the product before each use; do not use if damaged.
  • Follow all installation and operation guidelines to avoid injury.
  • Do not expose the connector to water or moisture during installation or operation.

3. Setup and Installation

Each auto connector set typically includes a connector housing, pins, and seals. Proper installation requires the use of professional crimping pliers to attach wires to the pins.

3.1 Components Overview

Female connector housing with two pins, showing components included in a set.

Figure 1: Female connector set (housing and pins)

Male connector housing with two pins, showing components included in a set.

Figure 2: Male connector set (housing and pins)

3.2 Installation Steps

  1. Prepare Wires: Strip the insulation from the ends of the wires to be connected, exposing the conductor.
  2. Crimp Pins: Using professional crimping pliers, securely crimp the exposed wire conductors to the appropriate pins. Ensure a strong mechanical and electrical connection. If seals are provided, ensure they are correctly placed before crimping.
  3. Insert Pins into Housing: Carefully insert the crimped pins into the designated slots within the connector housing. Ensure they click into place, indicating they are fully seated and locked.
  4. Verify Connections: Gently tug on each wire to confirm that the pins are securely locked in the housing and that the crimps are solid.

4. Operation

Once the wires are properly installed into the connector housings, connect the male and female connectors by aligning them and pushing them together until they securely latch. To disconnect, typically press the release tab (if present) and pull the connectors apart.

5. Maintenance

  • Keep connectors clean and free from dirt, dust, and debris.
  • Ensure connectors remain dry to prevent corrosion and electrical issues.
  • Periodically inspect connections for any signs of wear, damage, or loose wires. Replace any damaged components immediately.
  • Avoid excessive force when connecting or disconnecting to prevent damage to the pins or housing.

6. Troubleshooting

If you experience issues with your electrical connection, consider the following:

  • No Connection: Check if pins are fully seated in the housing and if the male and female connectors are properly latched. Verify that wires are correctly crimped to the pins.
  • Intermittent Connection: Inspect for loose crimps, damaged wires, or corrosion on the pins.
  • Difficulty Connecting/Disconnecting: Ensure connectors are aligned correctly. Do not force connections; check for bent pins or obstructions.

7. Specifications

Attribute Value
Brand Name yuyi
Model Number 3-929080-5, 3-1355470-1, A0245459926, A2215450228
Application Automobile
EU LVD Voltage Low voltage: Below 50Vac or 75Vdc
Voltage None (as per product listing)
High-concerned chemical None
Origin Mainland China
Certification NONE (CE compliance indicated for low voltage directive)
Gender Female or male
Position 2 pin wire harness
Customization Yes
Package Quantity Under 5Pcs (e.g., 1 Pcs)
Available Types Female with Pin, Male with Pin, Female male with Pin, Female with wire, Male with wire

8. User Tips

  • Always double-check the connector type (male or female, with or without wire) before purchase to ensure compatibility with your application.
  • For best results and safety, use high-quality crimping tools designed for automotive electrical connectors.
  • Consider using heat shrink tubing over crimped connections for added insulation and strain relief.

9. Warranty and Support

9.1 Manufacturer Information

Manufacturer: Yueqing ChenYi Electric Co., Ltd
Address: 2nd Floor, Building 3, No. 12 Yongxing 1st Road, Chengdong Industrial Functional Zone, Chengdong Street, Yueqing City, Zhejiang Province, China
Phone: +86-15869652718

9.2 EU Authorized Representative

Representative: EUREPSTAR GmbH
Address: Schlüterstr. 3, 85057 Ingolstadt, Germany
Phone: +49-84188697744
Email: eurep@eurep-gmbh.de

9.3 Additional Documentation

A user manual in PDF format may be available for more detailed information. You can typically find this document referenced as: User manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.