1. Introduction
The Xiegu G90S is a portable 20W HF amateur radio transceiver featuring a Software Defined Radio (SDR) architecture and a built-in automatic antenna tuner (ATU). Designed for amateur radio enthusiasts, it offers excellent transceiving performance and a highly configurable function experience. The G90S is distinguished by its detachable display unit, allowing for flexible arrangement of the radio components.
2. Setup
2.1 Package Contents
Before beginning setup, please verify that all components are present:
- Xiegu G90S Transceiver Unit
- Hand Microphone
- DC Power Cable
- Data Cable (for PC connection)
- Hex Key (for assembly)
- Optional: Stand Assembly (if purchased with stand)

2.2 Physical Assembly
- Detachable Display Unit: The G90S features a detachable control unit. To separate, carefully unlatch the unit from the main radio body. This allows for remote placement of the control panel.


- Optional Stand Assembly: If your package includes a stand, assemble it using the provided hex key and screws. The stand often includes a cooling fan for extended operation.

2.3 Connections
- Antenna Connection: Connect your HF antenna to the ANT port on the rear of the transceiver. Ensure a proper 50-ohm impedance match for optimal performance.
- DC Power: Connect the provided DC power cable to the DC IN port on the rear panel. Ensure the power supply provides 12-15V DC and can deliver sufficient current (up to 8A).
- Microphone: Plug the hand microphone into the dedicated microphone port on the front panel or control unit.
- Key (CW): For CW operation, connect your Morse code key to the KEY port on the rear panel.
- Data/I/Q Output: The G90S offers diversified interfaces, including a baseband I/Q output. This allows connection to external devices for sound card-based or PC-based applications (e.g., XDT1).

3. Operating Instructions
3.1 Basic Operation
- Power On: Press the power button (usually labeled with a power symbol) to turn on the transceiver. The 1.8-inch high-brightness color TFT LCD screen will illuminate.
- Frequency Tuning: Use the main tuning knob to adjust the operating frequency. Fine-tuning can be achieved with smaller increments.
- Mode Selection: The G90S supports SSB (Single Sideband), CW (Continuous Wave), and AM (Amplitude Modulation) modes. Select the desired mode using the dedicated MODE button or encoder.
- Volume Control: Adjust the VOL knob to set the desired audio output level.

3.2 Advanced Features
- Automatic Antenna Tuner (ATU): The G90S has a built-in high-performance ATU. To activate, press the TUNE button. The ATU will automatically match your antenna to the transceiver for optimal power transfer.
- Spectrum and Waterfall Display: The 1.8-inch color TFT LCD screen provides a ±24kHz bandwidth spectrum display and a waterfall display, allowing you to visualize signal conditions in real-time.
- Software Defined Narrowband Filter: Utilize the software-defined narrowband filter, especially useful in CW mode (300Hz), to improve signal clarity and reduce interference.
- Front End Narrowband ESC Preselector: The high-performance front-end narrowband ESC preselector helps to filter out strong out-of-band signals, enhancing receiver performance.
- Direct Control: The G90S is designed for ease of use with a panel + top button construction. Most functions can be directly controlled via dedicated buttons and the multi-function encoder, reducing the need to navigate through menus.

4. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the transceiver. Avoid using harsh chemicals or abrasive materials that could damage the finish or screen.
- Environmental Conditions: Operate the G90S within the specified temperature range (0°C to 55°C). Protect the unit from excessive moisture, dust, and direct sunlight.
- Ventilation: Ensure proper ventilation around the transceiver, especially the heat sinks, to prevent overheating during prolonged operation. If using the optional stand with a fan, ensure the fan is clear of obstructions.
5. Troubleshooting
- No Power: Check the DC power cable connection and ensure the power supply is providing the correct voltage (12-15V DC) and sufficient current. Verify the power supply is switched on.
- No Signal Reception: Ensure your antenna is properly connected and tuned. Check the selected operating mode and frequency. Verify that the volume is turned up.
- Poor Transmission: Confirm the antenna is properly connected and the ATU has successfully tuned the antenna. Check the power output setting.
- Display Issues: If the display is blank or flickering, ensure the detachable control unit is securely connected to the main radio body.
6. Specifications
| Feature | Specification |
|---|---|
| Receive Frequency Range | 0.5MHz to 30MHz |
| Operating Voltage Range | 12 ~ 15V DC |
| Transmitting Frequency Range | All amateur bands in the range of 1.8 to 29.999 MHz |
| Standby Operating Current | 750mA @ Max |
| Working Mode | SSB/CW/AM |
| Transmit Working Current | 8A @ Max |
| Operating Temperature Range | 0 °C ~ 55 °C |
| Frequency Stability | ±2ppm (after 30 minutes of power on) |
| Machine Size | 120*45*210 mm (without protrusions, head unit combination status) |
| Machine Weight | About 1kg |
| Receiver Parameters | |
| Receive Sensitivity | Better than 0.25uV @12dB Sinad (PRE: ON) |
| Machine Dynamic Range | 90dB |
| Adjacent Channel Suppression | 60dB |
| Audio Output Power | 0.5W@ 4Ω |
| Optional Filters | SSB 2.4kHz / CW 300Hz |
| Transmitter Parameters | |
| RF Output Power | 20W |
| Spurious Suppression | ≥50dB |
| Carrier Suppression | ≥40dB |
| Sideband Suppression | ≥50dB |
7. User Tips
- Model Identification: The model covered by this manual is the Xiegu G90S. Please ensure you have the correct model, as other versions (e.g., G90, G90N) may have slight differences in features or specifications.
- Antenna Tuning: Always use the built-in ATU or an external tuner to ensure a low SWR (Standing Wave Ratio) for efficient power transfer and to protect the transceiver's final amplifier.
- Power Supply: Use a stable and adequately rated 12-15V DC power supply capable of providing at least 8 Amperes to prevent performance issues or damage.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the documentation provided with your purchase or contact the authorized Xiegu dealer or manufacturer directly. Keep your proof of purchase for warranty claims.