1. Product Overview
The QIACHIP KR2201G-4 is a wireless smart light switch system designed for convenient control of your lighting. It consists of a wireless wall panel switch and a mini relay receiver, communicating via RF 433Mhz frequency. This system eliminates the need for traditional wiring between the switch and the light fixture, offering flexible installation and control options.



2. Specifications
| Feature | Specification |
|---|---|
| Model Number | KR2201G-4 (Mini Smart Switch) |
| Working Voltage | AC 90V~250V |
| Quiescent Current | <5mA |
| Max Current | 10A |
| Max Load | 2200W (Integrated load of wireless receiver is 1000W) |
| RF Frequency | 433-433.92MHz |
| Receiving Sensitivity | >108 dbm |
| Working Temperature | -30°C to 80°C |
| Storage Remote Controls | Up to 25 pieces |
| Support Encoding | 1527 Learning code, 2262 Fixed code |
| RF Operating Mode | ASK superheterodyne wireless reception |
| Receiving Range | Open space: >50 meters; Indoor partition wall: 15 meters |
| Wall Switch Size | 86 standard size |
| Switch Battery | 1 pcs CR2032 coin cell battery (not included) |
| Material | Plastic (ABS, Flame Retardant) |
| Switch Type | Remote Control |
| Certification | RoHS, CE |
| Warranty | 2 years |


3. Setup
3.1 Receiver Installation
The mini relay receiver is designed to be compact and can easily fit into various wiring boxes such as canopy boxes, junction boxes, or standard electrical boxes. Ensure the power supply is disconnected before installation.

3.2 Wiring Diagram
Connect the receiver to your power supply and light fixture according to the diagram below. Always ensure power is off during wiring to prevent electrical shock.
- IN (Input): Connect to your AC 90V~250V power source (Live and Neutral).
- OUT (Output): Connect to your light fixture (Live and Neutral).

3.3 Wall Switch Battery Installation
The wireless wall switch requires one CR2032 coin cell battery (not included). Open the battery compartment as indicated by the arrow on the switch and install the battery correctly, observing polarity.
3.4 Pairing Method
Follow these steps to pair your wireless wall switch with the receiver:
- Open the battery compartment on the wall switch and install the CR2032 coin cell battery correctly.
- Connect the receiver input to the power supply.
- Press the receiver's learning button 2 times continuously. The red indicator light on the receiver will start flashing.
- Within a few seconds, press the desired key on the remote wall panel switch that you want to pair.
- When the red indicator light of the receiver flashes once more and then turns off, the pairing is successful.

3.5 Resetting the Receiver
To clear all paired remote controls from the receiver's memory, press the learning button on the receiver 8 times. All existing paired data will be deleted successfully.
4. Operating Instructions
4.1 Basic Operation
Once paired, simply press the corresponding button on the wireless wall panel switch to toggle the connected light fixture ON or OFF.
4.2 Control Configurations
The system supports various control configurations:
- One Switch Controls One Receiver: A single button on a wireless switch controls one light receiver.
- Multiple Switches Control One Receiver: Several wireless switches can be paired to control the same light receiver, allowing control from different locations (e.g., a stairway).
- One Switch Controls Multiple Receivers: A multi-gang wireless switch can be configured to control multiple individual receivers, each connected to a different light.


4.3 Signal Range and Penetration
The RF 433Mhz signal can effectively pass through walls. The receiving range is typically over 50 meters in open spaces and approximately 15 meters through indoor partition walls.

4.4 Flexible Placement
The wireless wall switches can be stuck on any flat surface, allowing for simple installation and adjustable placement at any time without needing to run new wires.

5. Maintenance
5.1 Battery Replacement
When the wireless wall switch's performance degrades or it stops responding, it may be time to replace the CR2032 coin cell battery. Carefully open the battery compartment, remove the old battery, and insert a new one, ensuring correct polarity.
5.2 Cleaning
To clean the devices, wipe them with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the plastic housing.
5.3 Material Safety
The receiver is made from flame-retardant ABS plastic, ensuring enhanced safety in your home.
6. Troubleshooting
- Switch not responding:
- Check if the wall switch battery (CR2032) needs replacement.
- Ensure the receiver is powered on and correctly wired.
- Attempt to re-pair the wall switch with the receiver (refer to Section 3.4).
- Poor signal range:
- Ensure the distance between the switch and receiver is within the specified range (15m through walls, 50m open space).
- Minimize obstacles like thick concrete walls or large metal objects between the switch and receiver.
- Light flickers or doesn't turn on/off reliably:
- Verify that the total load of the connected light fixture(s) does not exceed the receiver's maximum load (1000W for integrated load, 2200W max).
- Check all wiring connections to ensure they are secure and correct.
- Accidental control or interference:
- The system is designed with anti-interference features. If issues persist, ensure no other 433Mhz devices are operating on conflicting frequencies nearby.
- Consider resetting the receiver and re-pairing only the desired switches.
7. User Tips
- Optimal Placement: While the signal can pass through walls, placing the receiver in a central location or closer to frequently used switches can enhance responsiveness.
- Labeling: If using multiple switches or receivers, consider labeling them to easily identify which switch controls which light.
- Battery Life: To maximize battery life for the wall switch, avoid excessive rapid presses.
- Safety First: Always disconnect power at the circuit breaker before performing any wiring or installation on the receiver.
8. Warranty and Support
This QIACHIP KR2201G-4 Wireless Smart Light Switch comes with a 2-year warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. Please retain your proof of purchase for warranty claims.
For technical support, troubleshooting assistance, or warranty inquiries, please contact your retailer or the manufacturer's customer service. Provide your product model number (KR2201G-4) and a detailed description of the issue to expedite support.