1. Introduction
The Bafang M6C LCD Display is a sophisticated control panel and information center designed for Bafang electric bicycles. It provides essential riding data, allows control over various e-bike functions, and enhances your overall riding experience. This manual will guide you through the installation, operation, and maintenance of your M6C display.
Figure 1: Front view of the Bafang M6C LCD Display showing key riding data.
2. Package Contents
Please check the package for the following items:
- Bafang M6C LCD Display Unit
- Control Pad with buttons
- Mounting Brackets and Screws
- Connection Cables
3. Setup and Installation
Follow these steps to properly install your Bafang M6C LCD Display on your e-bike handlebars.
- Mount the Display Unit: Secure the M6C display unit to your e-bike handlebars using the provided mounting bracket. Ensure it is positioned for optimal visibility and does not obstruct your view or control of the bike. Tighten the screws firmly but do not overtighten.
Figure 2: M6C display and control pad mounted on handlebars.
- Mount the Control Pad: Attach the control pad (with +, -, Power buttons) to the handlebars in a position easily accessible by your thumb.
Figure 3: Top-down view of the display and control pad mounting.
- Connect Cables: Connect the display unit to the control pad using the short cable. Then, connect the main cable from the display unit to the corresponding port on your Bafang e-bike system. Ensure all connections are secure and properly seated. The display is designed for 60V systems.
Figure 4: Rear view of the M6C display with cable connections and 60V rating.
4. Operating Instructions
The M6C display provides intuitive control and information at your fingertips.
4.1 Power On/Off
- To turn on the display and your e-bike system, press and hold the Power button on the control pad for a few seconds.
- To turn off, press and hold the Power button again until the display shuts down.
4.2 Changing Assist Levels
- Press the + button to increase the pedal assist level.
- Press the - button to decrease the pedal assist level.
- The current assist level will be shown on the display.
4.3 Displaying Information
The M6C display shows various riding parameters:
- Speed: Current riding speed (km/h).
- ENERGY: Battery charge level indicator.
- TRIP: Distance covered during the current ride.
- ODO: Total accumulated distance.
- Other potential indicators may include motor power output, time, etc., depending on the specific firmware.
Figure 5: Close-up of the M6C display screen.
5. Maintenance
Proper maintenance ensures the longevity and optimal performance of your M6C display.
- Cleaning: Wipe the display screen and unit with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Water Protection: While the display is designed to be weather-resistant, avoid submerging it in water or exposing it to heavy rain for extended periods.
- Connection Checks: Periodically check all cable connections to ensure they are secure and free from corrosion or damage.
- Storage: When not in use for extended periods, store the e-bike and display in a dry, temperate environment.
6. Troubleshooting
If you encounter issues with your M6C display, try the following steps:
- Display Not Turning On:
- Ensure the e-bike battery is charged and turned on.
- Check all cable connections between the display, control pad, and e-bike system for looseness or damage.
- Try pressing and holding the Power button for a longer duration (5-10 seconds).
- Incorrect Readings (Speed/Distance):
- Verify that the speed sensor on your e-bike wheel is correctly installed and aligned.
- Ensure the wheel circumference setting in the display's advanced settings (if accessible) is correct for your wheel size.
- Buttons Not Responding:
- Check for any physical obstructions or debris around the buttons.
- Ensure the control pad cable is securely connected to the display unit.
If problems persist, contact your dealer or a qualified e-bike technician for assistance.
7. Specifications
| Feature | Specification |
|---|---|
| Model | M6C |
| Display Type | LCD |
| Voltage Compatibility | 60V (as indicated on unit) |
| Functions Displayed | Speed, Energy (Battery Level), Trip Distance, Odometer (ODO), Assist Level |
| Origin | Mainland China |
| Package Dimensions (L x W x H) | 20 cm x 10 cm x 15 cm |
| Package Weight | 0.5 kg |
8. User Tips
- Always ensure your display is compatible with your Bafang motor system's voltage (e.g., 60V).
- Before each ride, quickly check that the display is securely mounted and all cables are connected.
- Familiarize yourself with the button functions before riding to ensure safe operation.
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided by your e-bike manufacturer or the seller (YQEBIKES Official Store). Keep your purchase receipt as proof of purchase.
