Introduction
This manual provides detailed instructions for the operation and maintenance of your Wurui D300 DMR Digital Walkie Talkie. Please read this manual thoroughly before using the device to ensure proper function and to maximize its performance and lifespan. The Wurui D300 is a professional-grade digital mobile radio designed for reliable communication across various environments, featuring a robust metal build, IP55 water resistance, and a powerful 10000mAh battery.
Safety Information
The manual has been compiled with great care to guarantee its correct and complete contents. The company shall not be held responsible for any possible character error or loss. The product design and specifications are subject to change without notice. Unless permitted by the Copyright Law, the manual shall not be copied, adapted, or translated without the prior written permission of this company.

Getting Started
Front Panel Overview

| No. | Component | Function |
|---|---|---|
| 1 | Power ON/OFF key | Turns the device on or off. |
| 2 | Palm Microphone/Programming Cable Jack | Connects the palm microphone or programming cable. |
| 3 | Frequency Band Toggle Key (A/B) | Switches between frequency bands A and B. |
| 4 | Working Mode Toggle Key (V/M) | Switches between Frequency Display Mode and Channel Mode. |
| 5 | FM Radio | Activates FM broadcast radio feature. |
| 6 | Exit/Lock Key | Short press to return to previous menu; long press to lock/unlock the keypad. |
| 7 | LCD Display | Shows operational information and menu. |
| 8 | Reduce Volume (CH-) | Decreases volume or navigates down in menus. |
| 9 | Down Key | Navigates down in menus. |
| 10 | Menu Key | Enters the main menu. |
| 11 | Up Key | Navigates up in menus. |
| 12 | Increase Volume (CH+) | Increases volume or navigates up in menus. |
| 13 | TX Indicator | LED glows red when transmitting. |
| 14 | RX Indicator | LED glows green when receiving. |
Rear Panel Connections

- Power Adapter: Use approved power supply wire cable to connect 13.8V DC. Red wire connects to positive, black wire connects to negative.
- External Speaker Jack: Connect approved external speaker (3.5mm plug only) to output audio.
- Antenna Connector: Connect external antenna, antenna impedance is 50Ω while transmitting.
Basic Operation
- PTT Switch: Push and hold to transmit, release to receive.
- A/B Key: Short press to switch the working frequency band. Long press to switch working mode at signal standby or dual standby.
- V/M Key: Short press to switch working mode between Frequency Display Mode and Channel Mode. Long press to switch working mode between analog and digital mode (This operation only can work in frequency mode).
- FM Key: Turn ON/OFF FM broadcast radio feature.
- EXIT Key: Short press to return back previous menu. Long press to lock/unlock the keypad.
- CH+/CH- Key: In standby mode, press to select an up/down channel or frequency. In menu mode, press to select previous or next menu/value.
- VOL+/VOL- Key: In standby mode, press to increase or reduce the audio output level. In menu mode, press to switch left and right when entering data.
- Palm Microphone: There are the same meaning and operation correspondence between palm microphone and panel keys. The extra [*] and [#] which to be used specially for menu operation, such as: when set the CTCSS/DCS, need to switch CTCSS or DCS, or need to delete previous character.
Menu Navigation and Features
Press the [MENU] key to enter the menu system, press [EXIT] key to exit step by step. There are 7 setting options in the primary menu.

Contacts
This menu mainly sets functions related to contacts.
- Contact List:
- Display all the contact list, press [MENU] key to enter the Secondary menu.
- Radio Detection: check if the radio of this single call number is in a receivable state.
- Call reminder: send a signal to the radio which works at private call, and the receiver will prompt.
- Remote monitoring: it can automatically let the receiver transmit, that is, it can monitor the other party.
- Remote Kill: remote kill the receiver.
- Remote Actived: remote active the receiver which already to be remote killed.
- View Details: view the name and call number of this contact list.
- Editing this contact list:
- Editing the call number: change the call number of this contact list.
- Editing the alias: change the alias of this contact list.
- Save: save the revised information.
- Delete: delete this contact list.
- Send Message: you can input and send text to this contact list.
- New Contact List:
- Input new call number: set up the new contact list.
- Input the alias: set up the alias of this new contact list.
- Save: save this contact list.
Message
Set up the features of message.
- New Message:
- You can create your desired text message (150 characters at most), press [*] key on palm microphone to delete previous character, press [#] key to change input methods.
- Press [MENU] key to next menu.
- View contact list: select and send message to this contact list which already be saved in the list.
- Input a call number: input a call number which to receive the message.
- Insert common phrase: insert the content of quick text into the editing interface.
- Save the draft: save the message you pre-set to the draft box.
- Exit the editing interface: exit and return back to message list.
- Quick Text: List all the quick texts which were pre-set through programming software.
- Inbox: List all the message of receiving already.
- Press [MENU] key to next subsidiary menu.
- Reply: reply the sender.
- Forward: forward the message to the others.
- Delete: delete the selected message.
- Delete All: delete all messages in the list of inbox.
- Press [MENU] key to next subsidiary menu.
- Outbox: List all the message of receiving already.
- Press [MENU] key to next subsidiary menu.
- View contact list: select a contact member in the contact list to send a message.
- Input call number: input the call number to send a message.
- Add the common phrase: add new quick text into the editing interface.
- Save the draft: save the message you pre-set to the draft box.
- Delete: delete the selected message.
- Exit the editing interface: exit and return back to message list.
- Press [MENU] key to next subsidiary menu.
Call Log
The menu is to set up the feature of call log.
- Outgoing List:
- List all outgoing log.
- Press [MENU] key to next subsidiary menu.
- View: view the details.
- Talking Time: display the talking time.
- Send Message: input and send message to the call number of this call log.
- Delete: delete this call log.
- Delete All: delete all call logs.
- Received Call:
- List all dialed calls.
- Press [MENU] key to next subsidiary menu.
- View: view details.
- Talking Time: display call time.
- Send Message: edit the message and send it to this contact.
- Delete: delete this message.
- Delete All: delete all records.
- Missed Call:
- List all dialed calls.
- Press [MENU] key to next subsidiary menu.
- View: view details.
- Talking Time: display call time.
- Send Message: edit the message and send it to this contact.
- Delete: delete this message.
- Delete All: delete all records.
Scan
Edit or set the scan list.
- Turn ON/OFF Scan feature: when scanning, there should be a list to scan in channel mode; but it can work directly in frequency mode.
- You can add the channel individually in this scan list, totally can add 16 channels.
- Press [MENU] key to view that already added what channel in the scan list.
- Re-press [MENU] key to add or delete the member in the list or delete the list.
- Add the channel: add the channel to the scan list, you cannot add the same channel repeatedly.
- Remove this channel: remove existing members.
- Delete the list: delete the scan list.
- Add the scan list, you can add totally 16 scan list.
Zone
- List of zones: there are totally 16 zones and each zone can be added 16 channels.
- Press [MENU] key to view that already added what channel in the zone list.
- Re-press [MENU] key to add or delete the member in the list or delete the list.
- Add the channel: add the channel to the list, you cannot add the same channel repeatedly.
- Remove this channel: remove existing members.
- Delete the list: delete the zone list.
- Add the zone list: add orderly the zone in the list till 16 zones.
Setting
Setting: setting the other features.
- Squelch Level: Setting the squelch level of analog channel.
- Battery Saving: Turn on or off battery saving feature and power saving ratio.
- Call Hang:
- Select the contact list of transmitting for digital channels.
- Off: transmitting based on the setting of contact list.
- 1S~10S: If the current channel receives a call within this time range, the transmission is transmitted with the received contact. If it has not been transmitted or is being received after the set time, it will be transmitted with the set contact.
- Transmitting Channel:
- Editing the channel: transmit based on current working channel.
- Busy channel lockout 1S~10S: transmit on the channel that received the signal, and transmit on the working channel after the set time.
- Language: Select the Chinese or English language to display.
- Backlight: Set the light time of backlight.
- Prompt Tone: Turn on or off the prompt tone when press the keypad.
- Keypad Lock: Set to lock the keypad automatically or by hand. When set to lock automatically, if there is not any operation in 15 seconds, the keypad will be locked automatically.
- Roger Tone: There will be a roger tone when end the transmitting (It only works in analog channel).
- Turn on or off GPS: Turn on GPS feature. There will be an icon on display when turn on this feature.
- Night Mode: Turn on or off night mode. When turn on this feature, the color of display will be changed.
- Squelch Tail Elimination: This feature can only be used in analog channel, it will not decode the last tone when turn off this feature, recommend to turn on this feature.
Setting of Band A/B
Some features only can be used in digital channel, some features only can be use in analog channels. According to the setting type of current frequency band, the feature list may be different.
- Selecting a zone: Selecting a working zone.
- Channel Step: Setting the channel step in frequency mode.
- TX output power: Setting the TX output power.
- Bandwidth: Setting the narrow or wide bandwidth for analog channel.
- Time-out Timer: Setting the time-out timer.
- CTCSS/DCS:
- Setting the same CTCSS/DCS of transmitting and receiving.
- Press [*] key to selecting between CTCSS and DCS.
- Press [#] key to selecting normal DCS or invert DCS.
- Receiving CTCSS/DCS:
- Setting the receiving CTCSS/DCS.
- Press [*] key to selecting between CTCSS and DCS.
- Press [#] key to selecting normal DCS or invert DCS.
- Transmitting CTCSS/DCS:
- Setting the transmitting CTCSS/DCS.
- Press [*] key to selecting between CTCSS and DCS.
- Press [#] key to selecting normal DCS or invert DCS.
- Busy Channel Lockout: Setting the authority to transmit in analog channel. Allow to transmit: can transmit at any case. Carrier: you can't transmit when receiving the carrier. The same CTCSS: you can't transmit when the same CTCSS. The different CTCSS: you can't transmit when the different CTCSS.
- Authority of Transmitting:
- Set the authority of transmitting for digital channel.
- Inhibit Transmitting: inhibit to transmit at any case.
- Impolite Transmitting: you can transmit at any case.
- Transmitting when the same CC code: you can't transmit when there is the same CC code.
- Transmitting when the carrier: you can't transmit when there is a carrier.
- Offset Direction: Set the offset direction in frequency mode.
- Offset Frequency: Set the offset frequency in frequency mode.
- Color Code: Only can talk to each other when use the same color code.
- DMR mode:
- Direct Mode: there is not slot and can talk with each other by one to one.
- Repeater Mode: go through repeater.
- Dual-Slot: there are 2 slots and can talk with each other by one to one.
- Slot: Set the dual-slot trunk or real trunk.
- Receiving without Group Call: When turn on this feature, you can receive any calls. When turn on this feature, you can only receive the calls in the same group.
- Encryption Type: You can select the encryption type from disable, normal or enhanced.
- Encryption Group: Only can talk with the one using the same encryption type and group.
- GPS:
- Location of this radio (show the position when connecting with the Satellite positioning).
- Enter to display the longitude, latitude and altitude of this radio.
- Receiving the information of GPS.
- Receive the information of GPS from other radios.
- FM Broadcast Radio:
- Display of this feature:
- [DW] will be appeared on upper right corner when turn on FM radio feature.
- The working mode (channel mode or frequency mode) will be appeared on bottom left corner.
- The working frequency of FM radio will be appeared in the middle of display.
- Only in frequency mode, press [*] key on palm microphone to starting scan.
- Press [MENU] key to next subsidiary menu.
- OFF: turn off the FM radio feature.
- Working mode: frequency mode or channel model.
- Dual Watch: turn on or off dual watch feature.
- Save: save the current frequency to channel list.
- “CH-” in front of channel number means there already had frequency in this channel.
- Display of this feature:
Appendix
Device Information
Show you the firmware version, frequency range, etc.
Specifications

| General Specifications | |
|---|---|
| Working Frequency | 136-174MHz / 400-480MHz |
| Number of Channels | 3000 channels |
| Channel Space | Digital: 12.5KHz; Analog: 12.5KHz/25KHz |
| Operating Mode | Same frequency simplex |
| Operating Temperature | -20°C ~ +50°C |
| Operating Voltage | DC 13.8V, Negative ground |
| Weight | About 500g |
| Dimensions | 107 x 41 x 126mm (width x high x depth, not including outparts) |
| Waterproof / Water-Resistant | IP55 |
| Material | Metal |
| Is_Display | Yes |
| Walkie Talkie Type | Car |
| Origin | Mainland China |
| Transmit | |
|---|---|
| Output Power(w) | 10w-25w |
| Transmit power | ≤25W |
| Modulation noise | 40dB@12.5KHz |
| Emit stray radiation | -36dBm@<1GHz, -30dBm@>1GHz |
| Adjacent channel power | -60dBm@12.5KHz |
| 4FSK digital modulation | 12.5KHz (data only): 7K60FXD, 12.5KHz (data + voice): 7K60FXE |
| Modulation limit | 2.5KHz@12.5KHz |
| Idle time slot power | -57dBm |
| Modulation characteristics | +1dB ~ -3dB |
| Digital transmission bit error rate | ≤3% |
| Receive | |
|---|---|
| Frequency stability | +/-2.5ppm |
| Digital sensitivity | 0.3uV/-117.4dBm (BER 5%), 0.7uV/-110dBm (BER 1%) |
| Intermodulation | 60dB |
| Adjacent channel selectivity | 60dB@12.5KHz |
| Co-channel rejection | -8dB@12.5KHz |
| Spurious response suppression | 70dB |
| Receiving stray radiation | -57dBm@<1GHz, -47dBm@>1GHz |
| Barrage | 84dB |
| Rated audio power | 2W |
| Battery Capacity(mAh) | 10000 |
| Maximum Range | 10km-50km |
Note: The specifications are subject to change by technical improvement without notice.
Maintenance
- Keep the device clean and free from dust and moisture.
- Avoid exposing the radio to extreme temperatures or direct sunlight for prolonged periods.
- Do not use harsh chemicals or solvents for cleaning. Use a soft, damp cloth.
- Ensure all connections (power, antenna, microphone) are secure before operation.
- Regularly check the battery level and charge as needed to maintain optimal performance.
Troubleshooting
If you encounter issues with your Wurui D300, consider the following general troubleshooting steps:
- No Power: Check power connections and ensure the battery is charged. Verify the power adapter is functioning correctly.
- No Transmission/Reception: Ensure the antenna is properly connected. Check frequency and channel settings. Verify that Busy Channel Lockout is not preventing transmission.
- Poor Audio Quality: Check external speaker connections. Adjust volume levels. Ensure the microphone is clean and unobstructed.
- Keypad Unresponsive: Check if the keypad lock feature is active. Long press the EXIT key to unlock if necessary.
- Menu Navigation Issues: Refer to the 'Menu Navigation' section for correct key usage (MENU, EXIT, CH+/CH-).
For more complex issues, consult the programming software or contact customer support.
User Tips
- DTMF Tones: The provided manual pages do not explicitly detail how to activate DTMF tones. This functionality may be accessible through the programming software. Users are advised to refer to the software documentation or contact support for specific instructions on DTMF tone activation.
- Programming: For advanced settings and customization, utilize the official programming software and cable. Links are provided in the Support section.
- Battery Life: To extend battery life, enable the 'Battery Saving' feature in the settings menu.
- Night Mode: Use 'Night Mode' for improved display visibility in low-light conditions.
Warranty and Support
The manufacturer guarantees the quality of this product under normal use. For any technical assistance or support, please refer to the following resources:
- Programming Cable: A dedicated programming cable is required for software configuration. You can find it at: https://www.aliexpress.com/item/32815196531.html
- Programming Software + Driver: Download the necessary software and drivers for your device from: https://txq-radio.com/DownLoad/104972.html
Please note that unauthorized modifications or repairs may void your warranty. Always ensure you are using official software and accessories.