Makerbase MKS SERVO57C

Contents

MKS SERVO57C Closed Loop Stepper Motor Driver PCBA User Manual

Brand: Makerbase | Model: MKS SERVO57C

1. Introduction

The Makerbase MKS SERVO57C is a high-performance closed-loop stepper motor driver PCBA designed for applications requiring precise motion control, such as CNC machines and 3D printers. It integrates advanced FOC (Field-Oriented Control) algorithms for quiet and efficient operation, and supports RS485 communication for multi-machine setups.

MKS SERVO57C PCBA board

Figure 1: MKS SERVO57C PCBA board

2. Key Features

List of key features of the MKS SERVO57C

Figure 2: MKS SERVO57C Key Features

  • Supports four working modes: open-loop mode, closed-loop mode, FOC mode, and serial mode.
  • Pulse interface support with a maximum input pulse frequency of 120KHz.
  • USART (TTL) and RS-485 interfaces for multi-machine communication, supporting up to 256 slave addresses.
  • Maximum operating current of 5.2A, with a continuous operating current of 46A for MOSFET.
  • Built-in Torque, Velocity, Position Closed-Loop Control, and FOC Vector Control Algorithms.
  • Supports subdivision from 1 to 256 with internal interpolation capabilities.
  • Direct input for positive signal, negative signal, and PLC 24V signal.
  • Quickly restore default parameters via a dedicated key.

3. Specifications

Table of product parameters/specifications for MKS SERVO57C V1.0

Figure 3: MKS SERVO57C Product Parameters

Parameter Description
Board typeMKS SERVO57C V1.0
MicroprocessorAT32F421 (Cortex-M4, 120M)
MOSFETAH30H80Q (30V, 70A)
Encoder14bit magnetic encoder
RS485 transceiverMAX13487E (±15kV ESD-protected)
Working voltage12V-24V
Working current0-5200mA
Subdivision1-256 (default 16)
Frequency of update (Torque)20KHz
Frequency of update (Velocity)10KHz
Frequency of update (Position)10KHz
Maximum Speed3000RPM+
Motor vibrationLow
Motor noiseLow
Motor temperatureLow
Serial interfaceUSART (TTL), RS-485
Serial baudrate9600~256000
Serial address1 broadcast address, 255 slave addresses

3.1. Product Dimensions

Diagram showing MKS SERVO57C product size dimensions

Figure 4: MKS SERVO57C Product Size (Side View)

MKS SERVO57C PCBA Size diagram with mounting dimensions

Figure 5: MKS SERVO57C PCBA Mounting Dimensions

3.2. SERVO57C MB1 vs. MB2 Comparison

Table comparing MKS SERVO57C MB1 and MB2 versions

Figure 6: SERVO57C MB1 vs. MB2 Differences

4. Package Contents

The MKS SERVO57C MB1 package typically includes the following items:

MKS SERVO57C PCBA board with included accessories (adapter board, screws, magnet, wrench, data cable, heatsinks)

Figure 7: Package Contents Overview

Shipping list for MKS SERVO57C MB1

Figure 8: Detailed Shipping List

  • MKS SERVO57C MB1 (Motor not included) x1
  • Adapter board (MKS APT) x1
  • Hexagon socket screw (M3-7mm) x4
  • ABS gasket (3mm) x4
  • 6*2.5 Radial Magnet x1
  • Allen wrench - M3 x1
  • 6pin Data Cable (60cm) x1
  • Heat sink (15*14.5*13mm) x2

5. Setup and Installation

5.1. Physical Installation (Shell Assembly)

Follow these steps to install the MKS SERVO57C into its 3D printed shell (if applicable). You will need to prepare 4 self-tapping screws (M2.6*8) and 4 self-tapping screws (M2.0*8) yourself.

Diagram of 3D printed shell components (driver module cover, key cover, terminal cover, motor cable cover) and required screws

Figure 9: 3D Printed Shell Components

MKS SERVO57C shell installation steps

Figure 10: Shell Installation Steps

  1. Install the heat sink onto the driver board.
  2. Secure the driver board to the bottom shell using four M2.6*8 self-tapping screws through the positioning holes.
  3. Install the ABS spacer posts onto the corresponding four positioning holes on the motherboard.
  4. Attach the baffle to the signal terminal protection position on the motherboard.
  5. Use four M3 screws to fix the main case components together.
  6. Use two M2 self-tapping screws to secure the motor cable cover.
  7. Finally, fix the button cover with two M2 self-tapping screws to complete the housing installation.

5.2. Wiring

Refer to the following diagrams for proper wiring connections.

Diagram showing the MKS SERVO57C product interface with labeled components and connections

Figure 11: MKS SERVO57C Product Interface Overview

Detailed diagram of MKS SERVO57C product interface with component labels and LED indicator information

Figure 12: Detailed Product Interface and LED Indicator

5.2.1. Motor Wiring

Connect your stepper motor to the A+, A-, B+, B- terminals as shown:

MKS SERVO57C Motor Wiring diagram

Figure 13: Motor Wiring

5.2.2. RS485 Communication Wiring

For single or multi-machine RS485 communication, follow these diagrams:

Wiring diagram for MKS SERVO57C RS485 Single-Machine and Multi-Machine configurations

Figure 14: RS485 Single-Machine and Multi-Machine Wiring

5.2.3. Serial Port (TTL) Wiring

For TTL serial communication, connect as shown:

MKS SERVO57C Serial port (TTL) Wiring diagram

Figure 15: Serial Port (TTL) Wiring

5.2.4. MB2 Specific Wiring

If using the MB2 version, refer to this specific wiring diagram for control signals:

MKS SERVO57C MB2 Wiring diagram

Figure 16: MKS SERVO57C MB2 Wiring

5.3. Encoder Magnet Installation

Proper installation of the encoder magnet is crucial for accurate closed-loop operation.

Diagram detailing distance requirements between magnet and magnetic encoder for optimal performance

Figure 17: Encoder Magnet Distance Requirements

  • Ensure the magnet and the encoder chip are parallel.
  • Maintain a gap between 0.5 mm and 3.0 mm. A smaller gap generally yields better angle accuracy.
  • The center of the magnet must be aligned with the sensing center of the magnetic encoder chip.
  • The deviation in alignment should not exceed ±0.3 mm, as this will significantly affect absolute angle accuracy.
  • Recommended radial magnet size: φ6.00mm, height 2.5mm.

6. Operating Modes

The MKS SERVO57C supports four distinct operating modes:

  • Open-Loop Mode: Standard stepper motor operation without encoder feedback.
  • Closed-Loop Mode: Utilizes encoder feedback for position correction, preventing step loss.
  • FOC Mode: Field-Oriented Control for smoother, quieter, and more efficient motor operation.
  • Serial Mode: Control and parameter adjustment via serial communication (USART or RS485).

7. Control Software

The MKS SERVO57C can be configured and monitored using a dedicated control tool. This software allows for setting various parameters, controlling motor movement, and viewing real-time status.

Screenshot of the MKS SERVO57C control tool software interface

Figure 18: MKS SERVO57C Control Tool Interface

Key functions available in the control tool include:

  • Parameter Settings: Adjust various operational parameters such as subdivision (microsteps), acceleration, and more.
  • Motor Control: Initiate forward/reverse movement, set speed, and acceleration.
  • Motor Status Monitoring: View real-time motor direction, speed, acceleration, and overall status.
  • Parameter Reading: Read cumulative pulse numbers, encoder values, and position angle errors.
  • Factory Reset: Option to restore the driver to its default parameters.

8. Maintenance

  • Keep the PCBA clean and free from dust and debris.
  • Ensure proper ventilation to prevent overheating, especially when operating at high currents.
  • Regularly check all wiring connections for looseness or damage.
  • Avoid exposing the board to moisture or corrosive environments.
  • If a heatsink is provided, ensure it is securely attached for optimal thermal performance.

9. Troubleshooting

9.1. Blue LED Indicator Status

The blue LED on the MKS SERVO57C provides visual feedback on the board's status:

  • Lights up for 2 seconds: Indicates the board is performing a self-check during startup.
  • Often bright: Suggests motor calibration is needed or an abnormal condition exists.
  • Blinking: The motor may need to be restarted.
  • Extinguished: Indicates normal operation.

9.2. Common Issues

  • Motor not moving or erratic movement:
    • Check power supply voltage (12V-24V) and current capacity.
    • Verify motor wiring (A+, A-, B+, B-).
    • Ensure control signals (Stp, Dir, En) are correctly connected and active.
    • Check encoder magnet alignment and distance.
    • Review parameters in the control software.
  • Communication issues (RS485/TTL):
    • Verify wiring for RS485-A, RS485-B, RX, TX, GND, 3.3V.
    • Ensure correct baud rate and serial address settings in software.
    • Check for proper termination resistors in RS485 networks if applicable.
  • Overheating:
    • Ensure heatsinks are properly installed.
    • Verify adequate ventilation around the driver board.
    • Reduce operating current if possible.

10. User Tips

  • Versatile Application: This driver is well-suited for both CNC machines and 3D printers, offering closed-loop control for enhanced precision.
  • Microstep Adjustment: Microsteps (subdivision) can be easily changed via the provided control software, offering flexibility for different application requirements without needing a physical screen on the device itself.

11. Warranty and Support

For detailed user manuals, schematics, and 3D printable shell files, please refer to the official Makerbase GitHub repository:

For warranty claims or technical support, please contact your retailer or the manufacturer directly with your purchase details.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.