FLIPSKY FSESC 75300

Contents

Flipsky FSESC 75300 ESC User Manual

High Current Electronic Speed Controller with Water Cooling

1. Introduction

This manual provides essential information for the safe and efficient operation of your Flipsky FSESC 75300 Electronic Speed Controller (ESC). Please read this manual thoroughly before installation and use.

⚠ Warning: Protective equipment should be worn. Not to be used in traffic.

⚠ Important: It is recommended to keep firmware 5.2 from factory ship. Upgrading to newer firmware versions may damage the ESC.

2. Specifications

FeatureValue
ModelFSESC 75300
Voltage Range14-84V (3-20S LiPo safe)
Continuous Current300A (at 50V), 200A (at 75V)
Maximum Current350A
Supported SensorsABI, HALL, AS5047, AS5048A
EPRM150000
CPU32F405 (168MHz, Cortex-M4 with DSP)
Input SourcesPPM, ADC, NRF, UART, PAS
Communication PortsUSB, CAN, UART, SPI, IIC
Motor Wire Gauge8AWG
Power Cable Gauge8AWG
Waterproof LevelIP67 (with water cooling enclosure)
Dimensions (L*W*H)297mm * 115mm * 45mm (including water pipes and capacitors)

Key Features:

  • Regenerative braking
  • Sensored or sensorless operation + hybrid mode
  • Configurable RPM-, current-, voltage- and power limits
  • Throttle curve and ramping for all input sources
  • Seamless 4-quadrant operation
  • Motor revolution, ampere hour, watt hour counting
  • Real-time data analysis and readout through the communication port
  • Adjustable protection against: Low/High input voltage, High motor/input current, High regenerative braking current, High RPM
  • Digital and analog VCC produced by separate voltage regulators for accurate AD conversion
Flipsky FSESC 75300 dimensions: 115mm height, 297mm length, 45mm width. Voltage: 4-20S, Continuous Current: 300A.
Figure 2.1: Flipsky FSESC 75300 with key dimensions and basic specifications.

3. Setup and Installation

3.1 Package Contents

Before starting, ensure all components are present:

Flipsky FSESC 75300 ESC, water cooling tubes, USB cable, and various wiring harnesses including Hall sensor, UART, CAN, PPM, and SWD connectors. A wiring diagram is also shown.
Figure 3.1: Included components with the FSESC 75300.

3.2 Wiring Diagram

Carefully follow the wiring diagram for proper connection of the ESC to your battery, motor, and control peripherals.

Detailed wiring diagram for Flipsky FSESC 75300. Connections include: BATTERY (B-, B+), MOTOR (A, B, C), and various communication/sensor ports: 1. USB, 2. PPM, 3. CAN, 4. SWD, 5. COMM, 6. UART2, 7. HALL (GND, HALL3, HALL2, HALL1, TEMP, 5V, JST PH2.0). Other pins for UART2 (3.3V, GND, RX2, TX2), COMM (5V, GND, ADC1, RX/SDA, TX/SCL, ADC2, ADC3), CAN (GND, CANL, CANH, 5V), PPM (3.3V, CLK, DIO, GND), SWD (SWDIO, SWCLK, GND, 3.3V).
Figure 3.2: Comprehensive wiring diagram for the FSESC 75300.

3.3 Initial Connection and Configuration (VESC Tool)

The FSESC 75300 is compatible with VESC Tool for configuration. Ensure you use the recommended firmware version (5.2) to avoid potential damage.

  1. Connect the ESC to your computer via the USB port.
  2. Open the VESC Tool software.
  3. Click "AutoConnect" to establish a connection with the ESC.
  4. Navigate to "Setup Motors FOC" to configure motor parameters.
  5. Select the appropriate motor type (e.g., "Large Inrunner").
  6. Confirm motor selection when prompted.
  7. Configure battery settings, including battery type and cell series.
  8. Proceed with "Run Detection" to automatically detect motor parameters.
  9. Ensure "Detect all motors over CAN Bus" is checked if you have multiple ESCs connected via CAN.
Video 3.1: Demonstrates the physical connection of the ESC, water cooling, and the initial setup process using VESC Tool, including motor and battery parameter configuration and FOC detection.

4. Operating Instructions

4.1 Powering On/Off

Connect your battery to the ESC's power cables (8AWG). Ensure all connections are secure before applying power. Disconnect the battery when not in use.

4.2 Control Input

The ESC supports various input sources including PPM, ADC, NRF, UART, and PAS. Configure your preferred input method via the VESC Tool. For remote control, ensure your receiver is correctly connected to the corresponding port (e.g., PPM).

4.3 Water Cooling System

The FSESC 75300 features an aluminum case with water cooling. Ensure the water cooling system is properly connected and functioning to maintain optimal operating temperatures, especially during high current applications.

Side view of the Flipsky FSESC 75300 showing the water cooling fittings and transparent tubes connected.
Figure 4.1: Water cooling connections on the FSESC 75300.

4.4 Real-time Monitoring

Utilize the VESC Tool to monitor real-time data such as motor revolution, ampere hour, and watt hour counting through the communication ports (USB, CAN, UART, SPI, IIC).

5. Maintenance

  • Regularly inspect all wiring and connections for signs of wear, corrosion, or damage.
  • Ensure the water cooling system is free from blockages and leaks. Periodically check the water flow.
  • Keep the ESC clean and free from dust, dirt, and moisture. Although it has an IP67 rating with the enclosure, proper care extends its lifespan.
  • Avoid exposing the ESC to extreme temperatures or direct sunlight for prolonged periods.

6. Troubleshooting

ProblemPossible CauseSolution
ESC not powering onIncorrect battery connection, faulty battery, damaged power cable.Check battery voltage and connections. Ensure polarity is correct. Inspect power cables for damage.
Motor not spinning/unresponsiveIncorrect motor wiring, sensor issues, incorrect VESC Tool configuration, faulty motor.Verify motor phase and sensor wire connections. Re-run motor detection in VESC Tool. Check motor for damage.
OverheatingInsufficient water flow, high current draw, inadequate cooling.Ensure water cooling system is fully functional and free of blockages. Reduce load or improve cooling efficiency.
Unstable operation/random cut-offsVoltage spikes, loose connections, firmware issues, exceeding current/voltage limits.Check all connections. Verify VESC Tool settings for voltage/current limits. Ensure firmware is stable (recommended 5.2).
Firmware upgrade failed/ESC damaged after upgradeIncompatible firmware, power interruption during upgrade.It is strongly recommended to use the factory-shipped firmware (version 5.2). New firmware upgrades may damage the ESC. Contact support if damage occurs.

7. User Tips

  • Always double-check all wiring connections, especially polarity, before applying power to prevent damage.
  • For applications requiring high continuous current, ensure your water cooling setup is robust and provides adequate heat dissipation.
  • When configuring with VESC Tool, save your settings frequently and back up your configuration files.
  • Consider using a current sensor for precise monitoring of power consumption and to stay within safe operating limits.

8. Warranty and Support

For consumer electronic products (e.g., VESC/Motor/Battery), the warranty period is 2 months since the 7th day after shipment (the shipping date is checked by logistic record). Please contact Flipsky service@outlook.com to process the after-sale service. You can return it to us for free repair or replacement when we get it and analyzed it as a manufacturing failure. We will bear the return back to you shipping cost only. If the replacement or repair is not possible for you, a discount can be provided for the new replacement (excludes the shipping cost).

For non-electronic products, the warranty period is 2 months since the 7th day after shipment (the shipping date is checked by logistic record). You can return it to us for free repair or replacement when we get it and analyzed it as a manufacturing failure. We will bear the return back to you shipping cost only. If the replacement or repair is not possible for you, a discount can be provided for the new replacement (excludes the shipping cost).

The following conditions are not covered by the above warranty:

  • Cannot provide purchase channel source proof
  • Mechanical damage to electronic components or PCB
  • PCBA board has repair soldering iron traces (excluding solder the cable bullet connectors)
  • Wire damage or external impact damage
  • For non-waterproof products, there is water inflow
  • Abnormal applications beyond the product specifications

The warranty for products purchased from other channels: For products purchased not from https://flipsky.net, please contact the original purchase channel in first priority to deal with your problems.

Group-buy: follow above item 1 warranty policy, the warranty period will be processed since the 7th day after our received group-buy order's shipment (the shipping date is checked by logistic record). For end users, if there's any quality issue, please provide the after-sales warranty card number (which is shipped in your product package). Pls keep it well when you get your product to Flipsky service@outlook.com to process it.

For the products transferred by personal second transaction, pls provide your original source order number or warranty card number (only in group buy products) to us, we'll verify the purchasing source and if it's in warranty period. And warranty policy is only valid once to this product (e.g. if the original ordered product has used the warranty policy, after its second transaction personally, the warranty is invalid to this product).

Clarification:

  • Most products are tested before shipment, especially the VESC and motors are 100% tested and shipped as a good product before shipment. Any uncertain connection or information for VESC/Motors settings, please contact us before your installation.
  • No term warranty, in no case shall Flipsky's liability be greater than the actual purchase price of the product.
  • On the shipping way product orders cannot be canceled unless the extra shipping cost is agreed to be charged.
  • We're willful to provide repair service for reasonable charge if your product is out of warranty, while the service excludes both side's shipping cost.
  • This updated warranty policy is valid since 2018/11/1, and the previous ordered products before 2018/11/1 still follow the policy before updates.

For further support, please visit the official Flipsky website: https://flipsky.net/

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.