Lsdzs Lishui LSW1207-14M

Contents

LSW1207-14M Brushless Motor Controller Instruction Manual

For 48V 22A eBike Fat Electric Bicycle Accessories

1. Introduction

This manual provides essential information for the safe and efficient use of your LSW1207-14M Brushless Motor Controller. Please read this manual thoroughly before installation and operation, and retain it for future reference.

2. Safety Warnings

⚠️️ Please mind potential fire risk and strictly follow the instruction manual for charging and storage.

  • Always disconnect power from the battery before installation or maintenance.
  • Ensure all electrical connections are secure and correctly polarized to prevent damage to the controller or other components.
  • Do not expose the controller to water, excessive moisture, or extreme temperatures outside its specified operating range.
  • Only use this controller with compatible eBike components, including the motor, battery, and any display or throttle units.
  • If you are unsure about any installation steps or encounter difficulties, seek professional assistance from a qualified eBike technician.

3. Specifications

Feature Specification
ModelLSW1207-14M
TypeController for Brushless Motor (E-Bike)
Power Supply Voltage24V/36V/48V
Rated Voltage48V
Maximum Current22A (Maximum working current: 30mA)
Rated Current11A (Rated working current: 6~25A)
Low Voltage Protection42V
Throttle Adjustment Voltage1.2V-4.4V
Cover ColorSliver
Working Temperature-20℃ ~ 60℃
Storage Temperature-30℃ ~ 70℃
Off-state leakage current<1µA
OriginMainland China

Product number: LSW1207-14M

CE Marking: G3M20211-1592-16 (as seen on product label)

4. Package Contents

The package typically includes:

  • 1x LSW1207-14M Brushless Motor Controller
  • 1x Instruction Manual (this document)

Please inspect the package contents upon receipt to ensure all items are present and undamaged.

5. Setup and Installation

The LSW1207-14M controller is designed for eBike brushless motors. Proper installation is crucial for safe and optimal performance.

5.1 Wiring Diagram Overview

Refer to the following images for a visual guide to the controller's connections. The controller features multiple color-coded wires for various functions.

LSW1207-14M Controller with label showing specifications
Figure 1: Controller with specification label. The label indicates Rated voltage: 48V, Maximum current: 22A, Rated current: 11A, Low voltage protection: 42V, and Throttle adjustment voltage: 1.2V-4.4V. Product number: LSW1207-14M.
LSW1207-14M Controller showing multiple wire harnesses
Figure 2: Side view of the controller with various wire harnesses extending from one end, ready for connection.
LSW1207-14M Controller with detailed view of wire connectors
Figure 3: Close-up of the controller's wire connectors, showing different colors and types of plugs for various eBike components.
LSW1207-14M Controller with another view of wire connectors
Figure 4: Another perspective of the controller's wiring, highlighting the individual connectors and their color coding.

5.2 Connection Steps

Important: This is a customized product. Please ensure compatibility with your eBike system before attempting installation. If you are unsure, consult a qualified technician.

  1. Identify Wires: Carefully identify each wire bundle from the controller and their corresponding functions (e.g., motor phase wires, Hall sensor wires, throttle, brake, display, battery). Refer to the images for visual identification of the wire types.
  2. Motor Connections: Connect the three thick phase wires (typically green, blue, yellow) from the controller to the corresponding motor phase wires.
  3. Hall Sensor Connections: Connect the smaller Hall sensor wires (typically five wires: red, black, green, blue, yellow) from the controller to the motor's Hall sensor connector. Ensure correct color matching.
  4. Battery Connection: Connect the main power wires (red for positive, black for negative) from the controller to your eBike battery. Ensure correct polarity.
  5. Throttle Connection: Connect the throttle wires (usually red, black, green) to the eBike's throttle unit.
  6. Brake Lever Connections: Connect the brake lever wires (if applicable) to the controller. These connections typically cut power to the motor when brakes are applied.
  7. Display/Control Panel: Connect the display or control panel wires to the designated port on the controller.
  8. Other Accessories: Connect any other accessories (e.g., lights, PAS sensor) according to their specific wiring instructions and the controller's capabilities.
  9. Secure Connections: Ensure all connections are tight and insulated to prevent short circuits and ensure reliable operation.
  10. Mounting: Securely mount the controller in a protected area on your eBike, away from direct moisture, physical impact, and excessive heat.

6. Operating Instructions

Once the controller is correctly installed and all connections are secure:

  1. Power On: Turn on your eBike's battery and then the main power switch (if separate).
  2. System Check: Observe the eBike display (if present) for any error codes or unusual behavior.
  3. Throttle Test: Gently apply the throttle to ensure the motor responds smoothly. Start with low power and gradually increase.
  4. Brake Test: Test the brake levers to confirm they effectively cut power to the motor.
  5. PAS Test (if applicable): If your eBike has a Pedal Assist System, test its functionality by pedaling.

If any issues arise, refer to the Troubleshooting section.

7. Maintenance

To ensure the longevity and optimal performance of your LSW1207-14M controller:

  • Regular Inspection: Periodically check all wire connections for looseness, corrosion, or damage. Ensure insulation is intact.
  • Cleaning: Keep the controller clean and free from dust, dirt, and moisture. Use a dry, soft cloth for cleaning. Do not use harsh chemicals or abrasive materials.
  • Avoid Overheating: Ensure the controller has adequate ventilation and is not exposed to direct sunlight or extreme heat for prolonged periods, which can affect its performance and lifespan.
  • Storage: When not in use for extended periods, store the eBike and controller in a dry, temperate environment, within the specified storage temperature range of -30℃ ~ 70℃.

8. Troubleshooting

This section addresses common issues you might encounter with your eBike controller.

Problem Possible Cause Solution
Motor not responding Loose or incorrect connections, low battery charge, faulty throttle, motor malfunction. Check all wiring connections for security and correctness. Ensure the battery is adequately charged. Test the throttle for proper function. Inspect the motor for any visible damage or issues.
Intermittent power or erratic behavior Poor or corroded connections, damaged wiring, controller overheating, electromagnetic interference. Secure all connections and clean any corrosion. Inspect wires for cuts or damage. Ensure proper ventilation for the controller. Check for external sources of interference.
Controller gets excessively hot Motor overload, insufficient cooling, internal short circuit, prolonged high power usage. Reduce the load on the motor. Ensure the controller is not covered and has adequate airflow. Check for any short circuits in the wiring. Allow the controller to cool down.
E-bike display shows an error code Specific error code indicates a problem (e.g., Hall sensor error, motor error, communication error). Consult your eBike display manual for error code interpretation and specific solutions. Check corresponding connections (e.g., Hall sensor wires for Hall errors).

If the problem persists after attempting these solutions, contact customer support or a qualified eBike technician.

9. User Tips

  • Customization Details: As this is a customized product, it is crucial to provide the seller with accurate and complete information about your eBike's specific requirements (e.g., exact voltage, motor wattage, motor type, display model) when ordering to ensure you receive a compatible controller.
  • Document Existing Setup: Before disconnecting any old components or installing the new controller, take clear photos or make notes of your existing eBike wiring. This visual reference can be invaluable during the installation process.
  • Initial Testing: After completing the installation, perform an initial test at a very low speed in a safe, open area. This allows you to confirm that all functions (throttle, brakes, pedal assist) are working correctly before engaging in full-speed operation.

10. Warranty and Support

For any product-related issues, technical support, or warranty inquiries, please contact the seller directly. When contacting support, it is recommended to have your order number readily available. If reporting a defect or malfunction, providing clear images or videos of the issue can significantly expedite the support process.

The seller is committed to customer satisfaction. If you encounter problems with the product, it is advised to contact them before leaving feedback. They will work to resolve issues, including offering refunds or replacements for defective products within 15 days of receipt, provided the defect is due to the product itself and not user error, improper installation, or personal preference.

Attention: Modifications or cancellations to your order cannot be accepted after it has been shipped.

11. Statement of Compliance

This product is designed and manufactured in compliance with relevant industry standards. The CE marking (CE:G3M20211-1592-16) indicates conformity with health, safety, and environmental protection standards for products sold within the European Economic Area.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.