Flipsky FSBLM01

Contents

Flipsky Wireless Bluetooth Module 2.4G

Instruction Manual

1. Introduction

The Flipsky Wireless Bluetooth Module 2.4G (model FSBLM01) is designed to facilitate communication between your VESC (VESC-based ESC) and the VESC Tool mobile application via Bluetooth Low Energy (BLE). This module allows users to monitor real-time parameters, adjust motor settings, and configure app settings directly from an Android mobile device. Please note that this module currently supports Android mobile devices only.

Flipsky Bluetooth Module 2.4G with wires
The Flipsky Wireless Bluetooth Module 2.4G, designed for VESC communication.

2. Setup

Before using the Bluetooth module, ensure your VESC's UART port is enabled and configured with a baud rate of 115200. This is crucial for proper communication.

2.1. Connecting the Module

The module comes with a JST-PH2.0mm connector, available in 7-pin (for V4 VESC) and 8-pin (for V6 VESC) versions. Identify the correct connector for your VESC model.

JST-PH2.0mm 8P Female connector for V6 VESC
JST-PH2.0mm 8P Female connector, typically used for V6 VESC models.
JST-PH2.0mm 7P Female connector for V4 VESC
JST-PH2.0mm 7P Female connector, typically used for V4 VESC models.

Connect the module to the UART port on your VESC. Refer to the wiring diagrams below for specific connections based on your VESC version.

Wiring Diagram for FSESC 6.6
Wiring diagram for Flipsky FSESC 6.6 with Bluetooth module
Wiring connections for the Bluetooth module with FSESC 6.6. Connect GND, VTX, VRX, and VIN. Ensure 3.3V or 5V is selected for power, and ADC for analog input if used.
Wiring Diagram for FSESC 4.12
Wiring diagram for Flipsky FSESC 4.12 with Bluetooth module
Wiring connections for the Bluetooth module with FSESC 4.12. Connect GND, VTX, VRX, and VIN. Ensure 3.3V or 5V is selected for power, and ADC for analog input if used. Note the 5V selection wire.

2.2. Software Installation

Download the VESC Tool application for Android from the official VESC Project website:

3. Operating Instructions

Once the Bluetooth module is connected and the VESC Tool app is installed on your Android device, you can begin monitoring and configuring your VESC.

  1. Power On: Ensure your electric skateboard (with VESC and Bluetooth module) is powered on.
  2. Open VESC Tool App: Launch the VESC Tool application on your Android device.
  3. Connect via BLE: Within the app, navigate to the connection settings and select the Bluetooth Low Energy (BLE) option to connect to your module.
  4. Monitor Real-time Parameters: The app will display various real-time parameters, including:
    • Motor current
    • Motor power
    • Duty cycle
    • Battery voltage
    • Battery current
    • MOS temperature
    • Motor temperature
    • Charging current
    • Charging power
    • ERPM (Electrical Revolutions Per Minute)
  5. Adjust Settings: The app allows you to adjust parameters in motor settings (General, BLDC, DC, FOC, PID Controllers, Additional info) and app settings (General, PPM, ADC, UART, Nunchuk Nrf, and other parameters).
  6. Firmware Upgrade: The module supports firmware upgrades via mobile phones.
  7. VESC Terminal Input: The app also supports VESC terminal input for advanced configurations.
Screenshot of VESC Tool mobile display interface
Example of the VESC Tool mobile display interface, showing real-time motor and battery parameters.

Product Overview Video

A short video demonstrating the Flipsky Bluetooth Module and its features.

4. Maintenance

To ensure the longevity and optimal performance of your Bluetooth module, follow these general maintenance guidelines:

  • Keep the module dry and away from moisture.
  • Avoid exposing the module to extreme temperatures.
  • Handle the module with care to prevent physical damage to the PCB or antenna.
  • Ensure connections are secure and free from debris.

5. Troubleshooting

If you encounter issues with your Flipsky Bluetooth module, consider the following:

  • No Connection: Ensure the VESC's UART port is enabled and set to a baud rate of 115200. Verify all wiring connections are correct and secure.
  • Android Only: Remember that this module is designed for Android mobile devices. It will not work with iOS devices.
  • Firmware Mismatch: In some cases, a firmware mismatch between the Bluetooth module and the VESC controller can cause issues. Refer to the official Flipsky support resources for firmware updates or compatibility information.
  • Connection Distance: The actual communication distance is approximately 15 meters. Ensure your mobile device is within this range.

For further assistance, you can visit the Flipsky troubleshooting guide:

Having trouble using Flipsky Bluetooth?

6. Specifications

FeatureSpecification
Operating Voltage2.0V ~ 12V
Onboard ChipNRF51822
Communication DistanceApprox. 15 meters
Frequency Range2.4GHz
RF Receiver2.4 GHz multiprotocol
ProcessorARM Cortex-M0 32 bit
Memory256kB Flash & 16kB RAM
PCB Size27mm x 13mm
Connector Length90mm (2.0mm seven-pin four-wire)
Antenna Length145mm
Net Weight3.5g
MaterialComposite Material
For Vehicle TypeCars
UseVehicles & Remote Control Toys
Recommended Age14+ years
CertificationCE, NONE, CEROHS
FeatureSmall & Light
ApplicationFor electric skateboard

7. User Tips

  • This module has been reported to work very well with ESC 75100 and ESC 75200, including the VESC Tool application.
  • Users have found it to work flawlessly with the vx3 remote.
  • Ensure your VESC firmware is compatible with the Bluetooth module to avoid connection issues.

8. Warranty and Support

For warranty information, technical support, or further inquiries, please contact Flipsky directly through their official website or customer service channels. Keep your purchase receipt for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.