HLTNC DM865C

Contents

HLTNC DM865C Digital Stepper Motor Driver

User Manual

1. Product Introduction

The HLTNC series motor driver is a high-precision control device designed for stepper motors and closed-loop servo motors. It converts DC power into precise drive signals to control motor speed, torque, and position, featuring adjustable current output, micro-stepping functionality, and multiple protection mechanisms (overcurrent, overvoltage, overheating, short circuit). The stepper driver supports bipolar stepper motors with smooth micro-stepping up to 1/128, ensuring low-noise operation for general-precision applications. The closed-loop servo driver integrates encoder feedback processing, enabling real-time position correction and high-dynamic response for precision motion control. Compatible with most CNC systems (Grbl, Mach3, FANUC) and PLCs, the driver is widely used in CNC machining, robotic arms, 3D printing, and other automation scenarios.

HLTNC DM865C Stepper Motor Driver, angled view
Figure 1: HLTNC DM865C Stepper Motor Driver

2. Specifications

2.1 Core Technical Parameters

Item Specification (Stepper Driver) Specification (Closed-Loop Servo Driver)
Input Voltage Range 12V-48V DC 24V-72V DC
Output Current Range 0.5A-5.0A/Phase (Adjustable) 1.0A-8.0A/Phase (Adjustable)
Micro-Stepping Options 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128 1/1, 1/2, 1/4, 1/8, 1/16 (Encoder-Dependent)
Compatible Motor Type Bipolar Stepper Motors (NEMA 17/23/34) Closed-Loop Servo Motors (with Encoder)
Encoder Support (Closed-Loop) -- 5V Differential/Open-Collector Encoders (1000-2500 PPR)
Control Signal Interface Pulse/Direction (PUL+/PUL-, DIR+/DIR-) Pulse/Direction / CW/CCW / Analog Speed Control
Protection Functions Overcurrent, Overvoltage, Overheating, Short Circuit, Undervoltage Overcurrent, Overvoltage, Overheating, Short Circuit, Encoder Fault, Position Deviation Alarm
Operating Temperature -10°C ~ +60°C -10°C ~ +65°C
Storage Temperature -20°C ~ +80°C -20°C ~ +80°C
Protection Grade IP20 (Indoor Use) IP20 (Indoor Use)
Dimensions (L×W×H) 120mm × 80mm × 40mm (Approx.) 150mm × 100mm × 50mm (Approx.)
Weight 0.3KG 0.5KG
Output Frequency <200KHz (Stepper) <500KHz (Servo)

2.2 DM865C Specific Parameters

Parameter Min Typical Value Max Unit
Continuous output current 1 6.5A A
Input voltage 18 24 80VDC V
Logic input current 7 10 20 mA
Total Power 120 W
Pulse Frequency 0 - 200 KHz
Insulation resistance 500 MΩ
Digital output port logic current 100 mA
Digital output port withstand voltage - 24 V
Table of DM865C Driver Product Parameters and dimensions
Figure 2: DM865C Driver Product Parameters and Dimensions

3. Product Overview

3.1 Main Components

The DM865C driver features a robust design with clearly labeled interfaces for easy setup and operation.

Various views of the DM865C driver: Front, Side, Top, Bottom
Figure 3: DM865C Driver Views (Front, Side, Top, Bottom)
Detailed view of the DM865C driver's digital display, operation buttons, and terminal interfaces
Figure 4: DM865C Driver Digital Display, Buttons, and Terminal Interfaces
  • Power Input Terminal: AC/DC power connection (terminal block)
  • Motor Output Terminal: Connection for motor phase wires (A+/A-, B+/B-)
  • Control Signal Interface: Pulse/Direction/Enable signal input (DB9 or terminal block)
  • Encoder Interface (Closed-Loop): Encoder signal input (6-pin connector)
  • Configuration DIP Switches: Micro-stepping, current, and mode settings
  • Adjustment Potentiometers: Current limit and gain adjustment (servo driver)
  • Status LEDs: Power (PWR), Run (RUN), Alarm (ALM) indicators
  • Heat Sink: Aluminum alloy heat dissipation plate (for high-current operation)
  • Mounting Holes: Threaded holes for fixed installation (M4)

3.2 Product Video

Video 1: DM865C Driver Product Display

4. Installation and Wiring Steps

4.1 Pre-Installation Preparation

  1. Confirm the driver type (stepper/servo) matches the motor and application requirements.
  2. Verify the input voltage range is compatible with the power supply (avoid overvoltage damage).
  3. Check the driver's maximum output current exceeds the motor's rated current.
  4. Prepare tools: Screwdriver set, wire stripper, multimeter, terminal crimping tool, cable ties.
  5. Clean the installation surface (equipment control panel) and driver to remove dust or debris.

4.2 Mechanical Installation

  1. Place the driver on a flat, well-ventilated installation surface (ensure ≥10cm clearance around for heat dissipation).
  2. Align the driver's mounting holes with the equipment's bracket and secure with M4 bolts (torque: 2-3 N·m).
  3. For high-current operation (≥3A/phase): Install the optional heat dissipation fan or attach the driver to a metal heat sink.

4.3 Electrical Wiring

4.3.1 Power Supply Connection

  1. Turn off the power supply and disconnect the power cable for safety.
  2. Connect the power supply to the driver's power input terminal:
    • DC Power: Connect Positive (+) to driver's VCC terminal; Negative (-) to driver's GND terminal.
    • Ensure the power supply's rated current is ≥1.5 times the driver's maximum output current.
  3. Tighten the terminal screws firmly to prevent loose connections (risk of arcing).

4.3.2 Motor Connection

  1. Identify the motor's phase wires (A+, A-, B+, B-; refer to the motor manual).
  2. Connect the motor wires to the driver's motor output terminal:
    • Stepper Motor: A+ → Driver A+, A- → Driver A-, B+ → Driver B+, B- → Driver B-.
    • Servo Motor (Closed-Loop): A+ → Driver A+, A- → Driver A-, B+ → Driver B+, B- → Driver B-.
  3. Ensure no short circuits between wires (use a multimeter to check for continuity).
Diagram showing the connection between the DM865C Driver and an 86 Stepper Motor, with color-coded motor phase windings
Figure 5: DM865C Driver to Stepper Motor Wiring Example
Terminal Number Symbol Description Voltage Range
1 A+ A phase motor winding+
2 A- A phase motor winding -
3 B+ B phase motor winding+
4 B- B phase motor winding-
5 VCC Input DC Voltage is positive 18-80VDC
6 GND Input current voltage negative

4.3.3 Control Signal Wiring

  1. Connect the CNC system/PLC control signals to the driver's control interface:
    • Pulse Signal (PUL+): Connect to control system's pulse output positive terminal.
    • Pulse Signal (PUL-): Connect to control system's pulse output negative terminal.
    • Direction Signal (DIR+): Connect to control system's direction output positive terminal.
    • Direction Signal (DIR-): Connect to control system's direction output negative terminal.
    • Enable Signal (ENA+/-): Connect to control system's enable output (optional, for motor on/off control).
  2. Use shielded cables for control signals (keep away from power cables) to avoid electromagnetic interference.
Terminal Symbol Description Illustration
1 DIR+ Direction positive input Signal source +5V~24V universal, no need to connect resistors in series
2 DIR- Direction negative input
3 PUL+ Pulse positive input
4 PUL- Pulse Negative input
5 ENA+ Motor enable positive input When the signal is valid, the motor is in a free state and the motor is not locked
6 ENA- Motor enable negative input
7 ALM+ Alarm signal negative input
8 ALM- Alarm signal positive input
Wiring diagrams for common anode and common cathode connections
Figure 6: Common Anode and Common Cathode Connection Diagrams

4.3.4 Encoder Wiring (Closed-Loop Servo Driver)

  1. Connect the motor's encoder cable to the driver's encoder interface:
    • Encoder VCC (5V): Connect to driver's encoder power positive terminal.
    • Encoder GND: Connect to driver's encoder power negative terminal.
    • Encoder A: Connect to driver's encoder signal A terminal.
    • Encoder B: Connect to driver's encoder signal B terminal.
    • Encoder Z (Zero Pulse): Connect to driver's encoder signal Z terminal (optional).
  2. Secure the encoder cable with cable ties to prevent damage.

5. Configuration Settings

5.1 Stepper Driver Configuration

  1. Set the micro-stepping resolution via DIP switches (e.g., 1/16 for smooth motion, 1/2 for high speed).
  2. Adjust the current limit potentiometer to match the motor's rated current (use a multimeter to measure).
  3. Enable/disable the enable signal function (if required by the control system).

5.2 Closed-Loop Servo Driver Configuration

  1. Set the motor type and encoder resolution via DIP switches (match the motor's specifications).
  2. Adjust the position gain (KP) and speed gain (KI) potentiometers for optimal dynamic response.
  3. Set the overcurrent and overheating protection thresholds (default settings recommended for initial use).

5.3 Button Function Description

Button Function Description
M Function selection: P parameter, JOG, RESET, L parameter switching
▲ When the value is changed: +1, long press to increase rapidly. In jog mode: long press the motor to rotate forward
▼ When the value is changed: -1, long press to decrease quickly. In jog mode: long press the motor to reverse
◀
  1. Press and hold this key for 0.5 seconds. Enter parameter setting
  2. When setting parameters, press once to shift to the left once
  3. After the setting is completed, press and hold this key for 0.5 seconds to confirm that the setting is successful and return to the current function code
  4. When there is a fault, long press this key for 2 seconds to reset the fault
Table describing the functions of the DM865C driver's control buttons
Figure 7: Button Function Description Table

5.4 P Area Main Function Parameters

Parameter Description Range Default Notes
P-00Current Loop Proportional Gain P1-327671500
P-01Current Loop Integral gain I2-32766200
P-02Subdivision Setting200-512002000
P-09Holding Current Percentage0-10040
P-10Open Loop Current Percentage0-10050
P-15Pulse Filter Enable0-600-disable 1-enable
P-16Filter Time0-25600500 us
P-18Running Direction0-110-forward 1-reverse
P-19Internal Pulse acceleration0-5000200
P-20Max speed0-3000100
P-21Stroke number of Pulse0-655350
P-22Stroke number of Pulse0-65535200
P-23Reciprocating times0-2001
P-24Direction0-11
P-25Intervals0-300002000
P-26Reciprocate or not0-11
P-27Internal pulse or not0-100-Pulse mode 1-Internal running mode
P-28Internal Pulse running0-101- button running, 2-external button running (PUL+ PUL-), 3-Outer JOG (PUL+ PUL-, DIR+ DIR-)
P-29JOG speed0-300100
Table detailing P-area main function parameters for the driver
Figure 8: P Area Main Function Parameters

6. Operation Instructions

6.1 Basic Operation

  1. Power On Sequence: Turn on the power supply → Wait for the driver to initialize (PWR LED steady) → Send control signals from the CNC system/PLC.
  2. Speed Control: Adjust the pulse frequency from the control system (higher frequency = higher motor speed; do not exceed the driver's maximum output frequency).
  3. Direction Control: Toggle the DIR signal to change the motor's rotation direction (set via DIP switch for active high/low).
  4. Motor Enable/Disable: Activate the ENA signal to enable the motor (output current applied); deactivate to disable (motor free to rotate).
  5. Power Off Sequence: Stop sending control signals → Disable the motor (if ENA is used) → Turn off the power supply.

6.2 Closed-Loop Servo Driver Exclusive Operations

  • Position Correction: If the motor deviates from the target position, the driver automatically adjusts via encoder feedback (no manual reset required).
  • Alarm Handling: If the ALM LED is on, refer to Section 8 (Troubleshooting) to identify the fault (e.g., encoder error, overcurrent).
  • Gain Adjustment: For unstable motion (oscillation), reduce the position gain (KP); for slow response, increase KP slightly.

6.3 Operating Guidelines

  • Avoid sudden changes in pulse frequency (use acceleration/deceleration settings in the control system) to prevent motor overcurrent.
  • Do not exceed the driver's maximum output current or input voltage (risk of driver damage).
  • For continuous operation (24 hours), monitor the driver's temperature and reduce current if overheating occurs.
  • Do not disconnect the motor or encoder cables while the driver is powered on (risk of short circuit or component damage).

7. Maintenance and Care

7.1 Daily Maintenance

  • Clean the driver's surface and heat sink daily with a soft brush or compressed air (remove dust to ensure heat dissipation).
  • Check the wiring connections for loosening (vibration may cause gradual disconnection).
  • Inspect the status LEDs during operation (ensure no abnormal alarm activation).

7.2 Regular Maintenance (Every 3 Months)

  • Tighten all terminal screws (power, motor, control signals) with a screwdriver (avoid over-tightening).
  • Clean the encoder interface (closed-loop driver) with a dry cloth (remove dust or debris).
  • Test the protection functions (overcurrent, overheating) by simulating fault conditions (professional personnel only).
  • Check the power supply voltage stability (fluctuations ≤±10% of rated input voltage).

7.3 Long-Term Storage (≥1 Month)

  • Disconnect all wiring connections and clean the driver thoroughly.
  • Store the driver in a dry, well-ventilated environment (humidity ≤60%, temperature 0°C ~ +30°C).
  • Avoid storing near high-temperature sources, magnetic fields, or corrosive substances.
  • Re-test the driver before reuse (check for proper initialization and output).

8. Important Safety Notes

  • Ensure the driver is properly grounded to prevent electric shock and electromagnetic interference.
  • Wear protective gloves and goggles during installation/wiring (risk of electric shock from power supply).
  • Do not touch the driver's heat sink or terminals during operation (may be hot).
  • Do not disassemble the driver without authorization—this will void the warranty and damage internal components (e.g., power modules, microcontrollers).
  • Disconnect the power supply before wiring, maintenance, or replacing the driver.
  • Keep the driver away from water, oil, dust, and high-temperature environments (exceeding 60°C).
  • Use only compatible motors and power supplies (refer to Section 2 for technical parameters).

9. Troubleshooting

Fault Phenomenon Possible Causes Troubleshooting Methods
Driver PWR LED Not Lit
  1. Power supply disconnected;
  2. Input voltage out of range;
  3. Power terminal loose
  1. Check power connection;
  2. Verify input voltage (12-48V DC for stepper, 24-72V DC for servo);
  3. Tighten power terminals
Motor Fails to Rotate
  1. Wrong motor wiring;
  2. Control signals not received;
  3. Motor disabled (ENA signal);
  4. Overcurrent protection triggered
  1. Recheck motor phase wiring;
  2. Test control signals with a multimeter;
  3. Activate ENA signal;
  4. Reduce current limit
Alarm LED (ALM) On (Closed-Loop)
  1. Encoder wiring error;
  2. Encoder damaged;
  3. Position deviation excessive;
  4. Overheating
  1. Recheck encoder connections;
  2. Replace encoder;
  3. Adjust gain or reduce load;
  4. Improve ventilation
Motor Jitter/Vibration
  1. Micro-stepping setting too low;
  2. Control signal interference;
  3. Current limit too low
  1. Increase micro-stepping (e.g., 1/16);
  2. Use shielded control cables;
  3. Adjust current limit to match motor rated current
Driver Overheating
  1. Current limit too high;
  2. Poor ventilation;
  3. Continuous high-load operation
  1. Reduce current limit (within motor rated current);
  2. Add heat dissipation fan;
  3. Reduce load or operating time
Incorrect Rotation Direction
  1. DIR signal wiring error;
  2. DIP switch setting (active high/low);
  3. Motor phase wires reversed
  1. Recheck DIR signal connection;
  2. Toggle the DIR polarity DIP switch;
  3. Swap motor A+ and A- (or B+ and B-) wires

10. Packaging List

Product packaging illustrations: professional packing box, single item packed with EPE, and completed packaging
Figure 9: DM865C Driver Packaging
  • Stepper/Servo Motor Driver ×1
  • Power Connection Cable (1.5m) ×1
  • Motor Connection Cable (1.5m) ×1
  • Encoder Cable (1.5m, Closed-Loop Only) ×1
  • DIP Switch Configuration Guide ×1
  • Mounting Bolts (M4) ×4
  • User Manual (This Document) ×1

11. Warranty and Support

  • Warranty Period: 12 months warranty against manufacturing defects (non-human damage).
  • Warranty Exclusions: Damage caused by improper wiring, overvoltage/overcurrent, disassembly, misuse, or natural disasters.
  • Technical Support: For wiring, configuration, or performance issues, contact our technical team with the driver model, motor specifications, and fault description.
  • Replacement Parts: Original replacement parts (cables, fuses, terminal blocks) are available for purchase.

Version: V1.0

Applicable Models: HLTNC Stepper Motor Driver Series / HLTNC Closed-Loop Servo Driver Series

Date: [Leave Blank for Customization]

For further assistance, please refer to the official PDF user manual: User Manual (PDF)

12. User Tips

  • Optimal Performance: For best results, ensure your power supply voltage is on the higher end of the recommended range (e.g., 48V-80V DC) to achieve higher motor speeds and faster response times.
  • Heat Management: Always ensure adequate ventilation around the driver. For continuous high-current operation, consider adding an external heat dissipation fan to prevent overheating and prolong the driver's lifespan.
  • Wiring Best Practices: Use shielded cables for control signals to minimize electromagnetic interference, especially in noisy industrial environments. Double-check all connections before powering on to avoid damage.
  • Digital Display Advantage: Utilize the integrated digital display for quick and accurate parameter adjustments and real-time status monitoring. This eliminates guesswork and simplifies troubleshooting.
  • Motor Matching: Ensure the motor's rated current is properly matched with the driver's current limit settings to prevent motor or driver damage and achieve smooth operation.

© 2023 HLTNC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.