K&F CONCEPT A255C2+BH-35L

Contents

K&F CONCEPT Professional Carbon Fiber Tripod User Manual

Model: A255C2+BH-35L

1. Product Overview

The K&F CONCEPT A255C2+BH-35L is a professional carbon fiber tripod designed for DSLR cameras, point & shoot cameras, special cameras, and mirrorless system cameras. It features a 360° rotatable ball head and a high load capacity, making it suitable for diverse photography needs. Its carbon fiber construction ensures it is both lightweight and strong.

K&F CONCEPT A255C2+BH-35L Carbon Fiber Tripod with Ball Head
K&F CONCEPT A255C2+BH-35L Carbon Fiber Tripod with Ball Head

2. Package Contents

Please check the package contents upon receipt to ensure all items are present and undamaged.

  • 1 x K&F CONCEPT A255C2+BH-35L Carbon Fiber Tripod
  • 1 x BH-35L Ball Head (pre-attached or separate)
  • 1 x Carry Bag
  • Instruction Manual (this document)
Tripod and carry bag included in the package
Tripod and carry bag included in the package

3. Setup Instructions

3.1 Unfolding the Tripod

  1. Place the tripod on a flat, stable surface.
  2. Release the leg angle locks and extend the tripod legs to your desired angle.
  3. Twist the leg section locks counter-clockwise to loosen, extend the leg sections, and then twist clockwise to secure them.
Hand demonstrating the twist lock mechanism on a tripod leg
Twist Lock mechanism for leg extension

3.2 Attaching Your Camera

  1. Ensure the quick release plate is securely attached to your camera's tripod mount.
  2. Open the clamp on the BH-35L ball head.
  3. Slide the quick release plate with your camera into the clamp and tighten the clamp knob until your camera is secure.

3.3 Using the Center Column

The tripod can be used with or without the center column. Using the center column allows for greater height, while removing it can provide enhanced stability, especially in windy conditions or for low-angle shots.

  • To extend the center column: Loosen the center column locking knob, extend the column to the desired height, and tighten the knob.
  • To remove the center column: Unscrew the locking knob at the base of the center column (often located where the legs meet the column). The center column can then be pulled out.
Comparison of tripod stability with and without center column
Enhanced stability with no center column vs. convenience with center column

3.4 Monopod Conversion

One of the tripod legs can be detached and combined with the center column to form a monopod.

  1. Unscrew the leg that has a foam grip (this is typically the detachable leg).
  2. Unscrew the center column from the tripod base.
  3. Attach the detached leg to the bottom of the center column.
  4. Attach the ball head to the top of the assembled monopod.
Diagram showing how to convert the tripod into a monopod
Detachable monopod conversion steps

3.5 Attaching Accessories

The tripod features two 1/4" interfaces for mounting additional accessories such as magic arms, phone clips, or external lights.

Tripod with accessories mounted on 1/4 inch interfaces
Tripod with two extra 1/4" interfaces for accessories

4. Operating Instructions

4.1 Adjusting Height and Leg Angles

Adjust the height by extending the leg sections using the twist locks. The leg angles can be independently adjusted to adapt to uneven terrain or for low-angle shooting.

Diagram showing various height configurations of the tripod and monopod
Various height configurations of the tripod and monopod

4.2 Using the BH-35L Ball Head

The BH-35L ball head allows for smooth and precise camera positioning. It features a 360° rotatable base for panoramic shooting and a main locking knob to secure the ball in place.

  • Main Locking Knob: Loosen to adjust the camera angle, tighten to secure.
  • Panoramic Base Knob: Loosen to rotate the camera horizontally for panoramic shots, tighten to lock.
Camera mounted on tripod with 360 degree rotatable ball head
360° Rotatable Ball Head for panoramic shooting

4.3 Product Demonstration Video

This video demonstrates the setup, usage, and key features of the K&F CONCEPT A255C2+BH-35L tripod.

5. Maintenance

5.1 General Care

  • Keep the tripod clean and free from dust, sand, and moisture.
  • Avoid exposing the tripod to extreme temperatures or harsh chemicals.
  • The carbon fiber material is weather, corrosion, and scratch-resistant, but proper care will extend its lifespan.
Close-up of carbon fiber tripod leg texture
Carbon fiber material provides durability and lightweight design

5.2 Cleaning

  • Wipe down the tripod with a soft, damp cloth after each use, especially if used in dusty or sandy environments.
  • For stubborn dirt, use a mild soap solution and rinse thoroughly. Ensure all parts are completely dry before storage.
  • Do not use abrasive cleaners or solvents, as these can damage the finish.

5.3 Storage

  • Store the tripod in its provided carry bag in a cool, dry place.
  • Ensure all knobs and locks are slightly loosened during long-term storage to prevent stress on components.

6. Troubleshooting

6.1 General Issues

  • Tripod instability: Ensure all leg sections are fully extended and locked, and leg angles are set appropriately for the terrain. If using the center column, consider removing it for maximum stability.
  • Difficulty with leg extension/retraction: Check for sand or debris in the twist lock mechanisms. Clean thoroughly if necessary.
  • Ball head movement not smooth: Ensure the main locking knob is sufficiently loosened. If still stiff, a small amount of silicone grease can be applied to the ball (consult manufacturer for recommended lubricants).

6.2 Monopod Assembly Issue

If you encounter issues with mounting the monopod, specifically with thread compatibility:

  • Ensure you are using the correct thread adapter if your camera or accessory requires a different size (e.g., 1/4" vs. 3/8"). The BH-35L ball head typically uses a 3/8" bottom interface, and the quick release plate uses a 1/4" screw for the camera.
  • Verify that the detached leg and center column are correctly threaded together before attaching the ball head.

7. Specifications

FeatureSpecification
Model NumberA255C2+BH-35L
MaterialCarbon Fiber
Leg Sections5
Max Extended Length1560mm / 156 cm / 61.4"
Folded Length490mm / 49 cm / 19.3"
Load Capacity15kg / 33lbs
Tripod Weight1.3kg / 2.9lbs
Ball Head ModelBH-35L
Ball Head Load Capacity15kg / 33.1lbs
Ball Diameter3.5 cm / 1.38"
Ball Head Bottom Interface3/8"
Ball Head Height8 cm / 3.15"
Ball Head Weight0.26 kg / 0.58 lbs
FeaturesDetachable Monopod, 360° Panoramic Ball Head, Compact & Portable, Weather/Corrosion/Scratch-resistant
Use For360° Video Camera, Point & Shoot Cameras, Special Camera, Mirrorless System Camera
Detailed specifications for K&F CONCEPT A255C2+BH-35L tripod
Main Tripod Specifications
Detailed specifications for BH-35L ball head
BH-35L Ball Head Specifications

8. User Tips

  • Optimal Height Adjustment: For comfortable shooting, a general guideline is to set the tripod height to approximately your height minus 15cm, then adjust for your camera's height.
  • Load Capacity: Always ensure your camera and lens combination does not exceed the tripod's maximum load capacity of 15kg (33lbs) to maintain stability and prevent damage. If your equipment is 2kg, it is suggested to choose a tripod bearing above 4kg.
  • Carbon Fiber Advantage: Carbon fiber tripods are significantly lighter and stronger than aluminum counterparts, offering enhanced portability and durability without rusting.
  • Twist Lock vs. Lever Lock: The twist lock mechanism on this tripod is simple, easy to replace parts, disassemble, clean, and maintain.
  • Ball Head Quality: The included ball head is made entirely of metal, contributing to its durability and smooth operation.

9. Frequently Asked Questions (FAQ)

Q: How to choose the height of the tripod?
A: Choose a tripod that is suitable for your height. Tripod height = your height -15cm - camera height. If you have additional requirements, you can choose according to the actual situation.
Q: What is the difference between carbon fiber tripod and aluminum tripod?
A: For the same size tripod, carbon fiber will weigh about 30% less than aluminum alloy, and its strength will be higher, and it will not rust. But also a little more expensive.
Q: How to choose the tripod loading capacity?
A: You can choose according to the weight of camera and lens, for example, if your equipment is 2kg, it is suggested to choose the tripod bearing above 4kg.
Q: What is the difference between the twist lock and the lever lock?
A: The structure of the twist lock is simple, easy to replace parts, disassemble, clean and maintain. The lever lock opens faster and is easy to operate with one hand.

10. Warranty and Support

This K&F CONCEPT tripod comes with a 1-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please contact K&F CONCEPT customer service through their official website or the retailer where the product was purchased.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.