1. Introduction
This manual provides comprehensive instructions for the installation, maintenance, and general use of the front and rear fenders designed for Zero 10 and T10 electric scooters. These fenders are essential accessories that help protect the rider and scooter from water, mud, and debris during operation, contributing to a cleaner and more enjoyable riding experience.

2. Safety Information
Please read and understand all safety warnings and instructions before installing or using this product. Improper installation or use can lead to damage to the product or scooter, and potential injury.
- Always ensure the scooter is powered off and stable before performing any installation or maintenance.
- Use appropriate tools for installation to prevent damage to fasteners or components.
- Regularly inspect fenders for secure attachment and any signs of damage.
- Do not modify the fenders or use them for purposes other than their intended design.
⚠ Important Safety Notice: While these fenders are passive components, ensure they are securely fastened to prevent interference with moving parts of the scooter, which could lead to accidents. Always follow the scooter manufacturer's guidelines for accessory installation.
3. Product Overview
The fender set includes a front fender and a rear fender, each designed to fit specific mounting points on the Zero 10 and T10 electric scooter frames. The rear fender typically includes an integrated taillight for enhanced visibility.
3.1 Front Fender


3.2 Rear Fender



4. Installation
Before beginning installation, ensure you have the necessary tools (e.g., screwdrivers, wrenches) and that your scooter is stable and powered off.
4.1 Front Fender Installation
- Locate the mounting points on the front fork of your Zero 10 / T10 scooter. These are typically pre-drilled holes.
- Align the front fender with these mounting points. Refer to Figure 3 for the fender's mounting hole pattern.
- Secure the fender using appropriate screws and washers (not included, typically provided with the scooter or purchased separately). Do not overtighten.
- Ensure the fender is centered over the wheel and does not interfere with wheel rotation or steering.
4.2 Rear Fender Installation
- Identify the mounting area for the rear fender, usually above the rear wheel and near the taillight wiring harness.
- If your scooter has existing taillight wiring, carefully connect the rear fender's taillight wires to the scooter's harness. Ensure correct polarity.
- Align the rear fender's mounting points with the corresponding holes on the scooter frame. Refer to Figure 6 for the fender's mounting hole pattern and wiring.
- Attach the fender using the appropriate fasteners.
- Verify that the taillight functions correctly and that the fender is securely mounted and does not rub against the wheel.
5. Functionality
Once properly installed, the fenders will provide protection against road spray and debris, keeping your scooter and yourself cleaner during rides, especially in wet conditions. The integrated taillight on the rear fender enhances your visibility to others, improving safety.
6. Maintenance
- Cleaning: Regularly clean the fenders with a damp cloth to remove dirt and grime. Avoid abrasive cleaners that could damage the material or finish.
- Inspection: Periodically check all mounting screws and bolts to ensure they are tight. Loose fasteners can lead to vibration, noise, or loss of the fender.
- Damage Check: Inspect fenders for cracks, breaks, or other damage, especially after impacts. Damaged fenders may not provide adequate protection and should be replaced.
- Taillight (Rear Fender): For the rear fender with an integrated taillight, periodically check that the light is functioning. If it fails, inspect wiring connections before considering replacement.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fender is loose or rattling | Loose mounting screws/bolts | Tighten all mounting fasteners. Apply thread locker if loosening persists. |
| Fender rubs against the wheel | Improper alignment during installation; bent fender or mounting bracket | Re-align the fender. Check for bent components and replace if necessary. |
| Rear taillight not working | Loose wiring connection; damaged bulb/LED; scooter electrical issue | Check and secure wiring connections. Test the taillight. Consult a scooter technician if the issue persists. |
| Excessive splashing despite fender | Fender is too short or improperly positioned | Ensure fender is correctly installed and covers the necessary area. Consider aftermarket extensions if available. |
8. Specifications
| Characteristic | Value |
|---|---|
| Length | 27 cm |
| Width | 17 cm |
| Height | 10 cm |
| Weight | 0.5 kg |
| Origin | Mainland China |
9. User Tips
- Compatibility: These fenders are specifically designed for Zero 10 and T10 electric scooters. Ensure your scooter model matches for optimal fit and performance.
- Pre-Ride Check: Always perform a quick visual check of your fenders before each ride to ensure they are securely attached and free from damage.
10. Warranty and Support
For detailed warranty information, please refer to the official product documentation or contact your retailer. For additional guidance or technical support, you may consult the comprehensive user manual available in PDF format: View User Manual (PDF).