1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the Dooya DM35S 6/28 Silent Fast Rolling Tubular Motor. This motor is designed for use with roller shades and blinds, offering quiet and efficient operation. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety Information
WARNING: Failure to follow these safety instructions could result in electric shock, fire, and/or serious injury.
- Ensure all electrical connections are made by a qualified electrician and comply with local electrical codes.
- Disconnect power before performing any installation, maintenance, or repair work.
- Do not expose the motor to moisture or extreme temperatures.
- Keep children and pets away from the operating area of the blinds.
- Do not attempt to modify or disassemble the motor.
- Ensure the motor is correctly matched to the tube diameter and weight of the blind.
3. Package Contents
Please check the package for the following items:
- Dooya DM35S 6/28 Tubular Motor
- Power Cable (4-wire)
- Crown and Drive Adapter (selected based on your tube type)
- Mounting Brackets
- Tail Plug
- Remote Controller (if included with your specific purchase)

4. Specifications
| Feature | Detail |
|---|---|
| Brand Name | Dooya |
| Model Number | DM35SL6/28 |
| Voltage | 220-240V |
| Wattage / Rated Power | 121W |
| Frequency | 50/60Hz |
| Torque | 6 Nm |
| Speed | 28 r/min |
| Protection Level | IP44 |
| Motor Diameter | 35 mm |
| Motor Length | 530 mm |
| Wiring | 4-wire |
| Compatible Tube Types | 45mm double grooved pipe, 50mm grooved pipe, 50mm round pipe, 40mm octagonal pipe. (Also compatible with 43mm, 47mm, 50mm tubes, ensure correct crown and drive adapter are used.) |


5. Installation and Setup
5.1 Tube Compatibility
The DM35S motor is compatible with various tube types. Before installation, ensure you have the correct crown and drive adapter for your specific tube. Common compatible tubes include:
- 45mm double grooved pipe
- 50mm grooved pipe
- 50mm round pipe
- 40mm octagonal pipe
- Other tubes such as 43mm, 47mm, 50mm (ensure proper crown and drive adapter)

5.2 Electrical Wiring
The DM35S is a 4-wire motor. Proper wiring is essential for safe and correct operation. Refer to the wiring diagram below for connections.
- Blue Wire: Neutral
- Brown Wire: Direction 1 (e.g., Up)
- Black Wire: Direction 2 (e.g., Down)
- Yellow/Green Wire: Earth/Ground
CAUTION: All electrical wiring should be performed by a qualified professional. Ensure power is disconnected before making any connections.

The diagram in Figure 6 shows the wiring for both 230V/50Hz and 120V/60Hz systems. Ensure you use the correct wiring configuration for your local power supply.
5.3 Motor Installation into Tube
- Insert the motor with the appropriate crown and drive adapter into one end of the roller blind tube.
- Ensure the motor is securely seated within the tube.
- Attach the tail plug to the opposite end of the tube.
- Mount the tube assembly with the motor into the mounting brackets, ensuring it is level and securely fastened.
- Connect the power cable to the motor and then to the main power supply as per the wiring diagram.
6. Operating Instructions
Once installed and wired, the motor can be operated using a compatible remote controller or wall switch (not explicitly detailed in provided data, but implied by "remote controller" in Figure 2). Typical operation involves:
- Up/Open: Press the 'Up' button on your remote or switch to raise the blind.
- Down/Close: Press the 'Down' button to lower the blind.
- Stop: Press the 'Stop' button to halt the blind at any desired position.
6.1 Setting Limit Positions
Tubular motors typically require setting upper and lower limit positions to prevent over-rolling. The motor features a 'Motor reset button' (see Figure 4). Consult the specific instructions provided with your remote control or wall switch for detailed steps on how to program these limits. This usually involves a sequence of button presses on the remote and possibly using the reset button on the motor itself.
7. Maintenance
The Dooya DM35S motor is designed for low maintenance. Follow these general guidelines:
- Keep the motor and surrounding area clean and free from dust and debris.
- Do not lubricate the motor. It is factory-sealed and does not require additional lubrication.
- Periodically check the mounting brackets and connections to ensure they are secure.
- If you notice any unusual noises or erratic operation, disconnect power and contact support.
8. Troubleshooting
If you encounter issues with your motor, try the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor does not respond | No power; Remote battery low; Wiring issue; Motor overload protection activated. | Check power supply; Replace remote batteries; Verify wiring connections; Allow motor to cool down. |
| Blind stops at incorrect positions | Limit settings incorrect. | Reprogram the upper and lower limit positions according to your remote's instructions. |
| Motor makes unusual noise | Obstruction in blind path; Motor fault. | Check for obstructions; If noise persists, contact support. |
| Motor runs in wrong direction | Wiring error for direction control. | Verify brown and black wire connections as per wiring diagram. |
9. User Tips
No specific user tips were available from reviews or Q&A for this product. General tips for tubular motors include:
- Always ensure the correct crown and drive adapter are used for your specific tube diameter to prevent slippage and damage.
- When programming limits, perform small adjustments and test thoroughly to achieve precise stopping points.
10. Warranty and Support
The Dooya DM35S 6/28 Tubular Motor comes with a 1-Year Manufacturer's Limited Warranty for defective items from the date of receipt. Accessories are covered by a 3-month warranty. This warranty does not cover items damaged due to misuse or improper installation.
For warranty claims, technical support, or any questions regarding your motor, please contact your seller or the manufacturer directly, providing your order number and a detailed description of the issue.