ASMTLED TM1903 SMD 3535 RGB

Contents

ASMTLED TM1903 Full Color Pixel LED Strip Instruction Manual

Model: TM1903 SMD 3535 RGB

Introduction

Thank you for choosing the ASMTLED TM1903 Full Color Pixel LED Strip. This product is a high-quality, addressable LED strip designed for dynamic and vibrant lighting effects. Featuring TM1903 ICs and 96 SMD 3535 RGB LEDs per meter, it offers full-color capabilities, including water, chase, and scan effects. This manual provides essential information for the safe and effective use of your LED strip.

Two rolls of ASMTLED TM1903 LED strips, one with a white PCB and one with a black PCB, both with JST SM connectors.
ASMTLED TM1903 Full Color Pixel LED Strip (White and Black PCB options)

Specifications

AttributeValue
LED Source3535 SMD RGB External TM1903 chipset
IC TypeTM1903 (Similar to WS2811)
Working Input Voltage12V DC
Output Power0.2W/LED
Drive ModeConstant Voltage
LED Quantity96 LEDs/Meter (3 LEDs are separately controlled)
IC Quantity32 ICs/Meter (1 IC drives 3 LED chips)
Pixels32 Pixels/Meter
Grey Scale256
ColorRGB (Rainbow Color)
View Angle120°
Working Temperature-20°C to 60°C
PCB ColorWhite/Black PCB
Waterproof RatingIP30 (Non-waterproof)
PCB Width8mm
Power ConsumptionMax 18W/Meter (11.52W/m)
Average Life1,000,000 hours
CertificationCE
OriginMainland China
Comparison of White and Black PCB LED strips, showing dimensions: 8mm width, 7.08mm between LEDs, and 31.3mm per segment. Also lists Length: 5m/lot, LEDs Number: 96leds/m, LED Chip Model: 3535SMD.
LED Strip Dimensions and Key Specifications

Package Contents

  • 1 x 5-meter ASMTLED TM1903 Full Color Pixel LED Strip

Note: Power supply and LED controller are NOT included and must be purchased separately.

Setup Instructions

  1. Prepare Components: Ensure you have a compatible 12V DC power supply and an LED controller for addressable LEDs (e.g., compatible with TM1903 or WS2811 ICs).
  2. Power Supply Compatibility: The LED strip requires a 12V DC power supply. Using an incorrect voltage will damage the strip.
  3. Wiring Connection: The LED strip comes with a 3-pin JST SM wire connector. Connect it to your LED controller as follows:
    • Red wire: +12V (Power)
    • Green wire: Data (Signal)
    • White wire: GND (Ground)
    Detailed view of the LED strip showing the 3-pin JST SM wire connector, indicating DC12V voltage, 96 LEDs/m, and TM1903 IC controller. Also shows the 3M adhesive tape on the back.
    LED Strip Connector and Adhesive Tape
  4. Power Cord Thickness: When selecting a power cord, consider the actual maximum current, the product's power consumption, and the wiring length (do not exceed 5 meters to avoid significant voltage drop).
  5. Cutting the Strip (Optional): The LED strip can be cut to your desired length. Each segment of 3 LEDs is controlled by one IC and can be cut independently. Look for the designated cut marks on the PCB.
    Close-up of the LED strip showing a Highlight LED Chip (3535 SMD RGB Lamp), a Safe resistor for stable voltage, and the TM1903 IC controlling three LEDs. It also indicates that the strip can be cut for DIY sizing.
    LED Strip Components and Cut Points
  6. Mounting: The strip features 3M adhesive tape on the back for strong adhesion and easy installation. Clean the surface thoroughly before applying the strip to ensure optimal adhesion.

Operating Instructions

Once properly connected to a compatible LED controller and 12V DC power supply, the ASMTLED TM1903 LED strip can be operated via the controller. The TM1903 IC allows for individual control of every 3 LEDs, enabling a wide range of dynamic full-color RGB effects such as:

  • Water flow effects
  • Chasing patterns
  • Scanning effects
  • Static colors
  • Color transitions and fades

Refer to your specific LED controller's manual for detailed instructions on selecting and customizing lighting modes and effects.

Video demonstrating various dynamic color changing effects of the LED strip.
Four panels showing the LED strip displaying solid red, solid green, and two different multi-color dynamic patterns.
Examples of dynamic and static color displays

Maintenance

  • Cleaning: Gently wipe the LED strip with a dry, soft cloth to remove dust. Do not use liquid cleaners or immerse the strip in water, as it is non-waterproof (IP30 rated).
  • Environmental Conditions: Operate the LED strip within its specified working temperature range of -20°C to 60°C. Avoid exposing it to extreme heat, cold, or direct moisture.
  • Inspection: Periodically check the connections and the strip for any signs of damage or wear. Ensure all connections are secure.
  • Storage: If storing the LED strip, ensure it is kept in a dry, cool place, away from direct sunlight and excessive humidity.

Troubleshooting

ProblemPossible CauseSolution
LED strip does not light upNo power, incorrect voltage, faulty connection, faulty controller.Check power supply connection and ensure it's 12V DC. Verify all wiring connections (VCC, Data, GND). Test with a different controller if available.
Some LEDs or segments are not workingDamaged segment, loose connection, IC failure.Inspect the affected segment for physical damage. Check solder points (normal to have them every 0.5m). If a segment is faulty, it may need to be cut out and replaced or bypassed.
Colors are incorrect or flickeringData signal issue, controller settings, voltage drop.Ensure the controller is set to the correct IC type (TM1903/WS2811) and LED count. Check data line connection. If the strip is very long, consider injecting power at multiple points to prevent voltage drop. Ensure power cord thickness is adequate for the length.
Adhesive tape not stickingSurface not clean, unsuitable surface material.Clean the mounting surface thoroughly with isopropyl alcohol and let it dry completely before applying. For rough or porous surfaces, additional mounting clips or adhesive may be required.

User Tips

  • Test Before Installation: Always test the entire LED strip with your controller and power supply before final installation to ensure all segments are working correctly.
  • Plan Your Layout: Before cutting or adhering, plan your desired layout. Measure carefully and mark cut points to avoid errors.
  • Power Injection: For longer runs (e.g., beyond 5 meters), consider injecting power at both ends or at intermediate points to maintain consistent brightness and color accuracy throughout the strip.
  • Controller Compatibility: Ensure your LED controller explicitly supports the TM1903 or WS2811 IC type for proper addressable control.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or ASMTLED Official Store directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.