1. Introduction
This manual provides essential information for the safe and efficient operation of your Flipsky FSESC75200 84V High Current Electronic Speed Controller (ESC) with Aluminum PCB. This VESC-based ESC is designed for high-power applications such as E-Foils, fighting robots, surfboards, and AGV robots. Please read this manual thoroughly before installation and use.

Figure 1: Front view of the FSESC75200.
2. Specifications
| Attribute | Value |
|---|---|
| Brand | Flipsky |
| Model | FSESC75200 |
| Firmware | 5.2 (supports firmware upgrade) |
| Voltage Range | 14-84V (safe for 4-20S battery configurations) |
| Continuous Current | 50V/200A; 75V/150A (dependent on mounting, ambient temperature, and air/water circulation) |
| Burst Current | 300A |
| BEC Output | 5V@1A |
| Supported Modes | DC, BLDC, FOC (sinusoidal) |
| ERPM | 150000 |
| Communication Ports | USB, CAN, UART, SPI, IIC |
| Supported Sensors | ABI, HALL, AS5047, AS5048A |
| Input Source Support | PPM, ADC, NRF, UART |
| Sensorless Operation | Yes |
| Regenerative Braking | Yes |
| Programmable | Via VESC_TOOL |
| Dimensions (L x W x H) | 130 x 67.7 x 40.1mm (Including aluminum case) |
| Motor/Power Wire Size | 8 AWG |
| Material | Composite Material (with Aluminum PCB) |
| For Vehicle Type | Cars |
| Is Electric | No Battery (requires external battery) |
| Is it battery/power supply | No (requires external power supply) |
| Is it charger/adapter | No (no integrated charger) |
| Recommend Age | 14+ years |

Figure 2: FSESC75200 dimensions.
3. Key Features
- Adjustable protection against: low voltage, high voltage, over current, abnormal temperature, MOSFETs/motor over temperature.
- Supports various control modes: Current, Duty Cycle, Speed, and PID control.
- Integrated IMU module support via IIC interface for balancing applications (e.g., MPU9250, MPU9150, MPU6050, LSM6DS3, BMI160).
- Equipped with a 32F405 CPU operating at 168MHz.
- Aluminum PCB for enhanced heat dissipation and extended lifespan.
- Two COMM ports for UART Bluetooth modules, screen displays, or remote controller support.
4. Setup and Installation
4.1. Important Firmware Information
It is strongly recommended to retain the factory-shipped firmware version 5.2. Upgrading to newer firmware versions (e.g., 5.3 or above) may cause damage to the ESC if not configured correctly.
For firmware versions 5.3 (VESC_TOOL 3.01) or above, the phase filtering function MUST be turned off by selecting "false" in VESC_TOOL. Failure to disable phase filtering will result in ESC damage. Do not restore default parameters when using the wizard interface with these firmware versions.
4.2. Wiring Diagram
Carefully follow the wiring diagram below for proper connection of your battery, motor, and peripheral devices. Ensure all connections are secure before applying power.

Figure 3: FSESC75200 Wiring Diagram.
- 1. USB: For connecting to VESC_TOOL on a computer.
- 2. PPM: Pulse Position Modulation input for remote control signals.
- 3. CAN: Controller Area Network bus for multi-ESC communication.
- 4. UART2: Universal Asynchronous Receiver-Transmitter port for accessories like Bluetooth modules or displays.
- 5. SWD: Serial Wire Debug for firmware development and debugging.
- 6. COMM: General communication port.
- 7. HALL: Hall sensor input for sensored motor operation.
- Battery: Connect your battery pack (4-20S, 14-84V).
- Motor: Connect the three phase wires of your motor.
Important: When disconnecting wires from the connectors, please press the release tabs on the connectors. Do not pull directly on the wires to avoid damaging them or the connectors.
4.3. Physical Installation

Figure 4: FSESC75200 Heat Sink.
Mount the ESC in a location that allows for adequate airflow to utilize its aluminum PCB and heat sink effectively. Proper heat dissipation is crucial for optimal performance and longevity, especially in high-current applications. Ensure the mounting surface is flat and secure.
5. Operation
The FSESC75200 supports various control modes including DC, BLDC, and FOC (sinusoidal). Configuration and fine-tuning of these modes are performed using the VESC_TOOL software.
5.1. VESC_TOOL Software
Connect the ESC to your computer via the USB port and use the VESC_TOOL software for:
- Motor detection and calibration.
- Setting up control modes (Current, Duty Cycle, Speed, PID).
- Configuring protection parameters (voltage limits, current limits, temperature limits).
- Monitoring real-time data and diagnostics.
Refer to the official VESC_TOOL documentation for detailed instructions on software usage and parameter settings. Always save your configuration settings after making changes.
5.2. Control Modes
- Current Control: Directly controls the motor current, providing precise torque control.
- Duty Cycle Control: Controls the voltage applied to the motor as a percentage of the battery voltage.
- Speed Control (RPM): Attempts to maintain a target motor speed.
- PID Control: Advanced control loop for precise regulation, often used in balancing applications with an IMU.
6. Maintenance
- Regular Inspection: Periodically check all wiring connections for looseness or damage. Ensure motor phase wires and battery cables are securely attached.
- Cleanliness: Keep the ESC free from dust, dirt, and moisture. Use compressed air to clean the heat sink fins if necessary.
- Temperature Monitoring: During operation, monitor the ESC temperature, especially in demanding applications. Ensure adequate cooling is maintained.
- Firmware Updates: Only update firmware if absolutely necessary and after carefully reviewing the latest guidelines from Flipsky or VESC project, paying close attention to warnings regarding phase filtering.
7. Troubleshooting
This section addresses common issues you might encounter with your FSESC75200.
7.1. Common Issues and Solutions
| Problem | Possible Cause / Solution |
|---|---|
| ESC not powering on / No response | Check battery connections and voltage. Ensure the battery is charged and within the 14-84V range. Verify all wiring is correct according to the diagram. |
| Motor not spinning or erratic behavior | Perform motor detection in VESC_TOOL. Check motor phase wire connections and Hall sensor connections (if used). Ensure correct control mode is selected. |
| ESC overheating | Check for adequate airflow around the ESC. Reduce load or current limits in VESC_TOOL. Ensure proper mounting for heat dissipation. |
| Sudden power cut-off during operation | This could be due to protection triggers (low voltage, over current, over temperature). Check battery voltage, current draw, and ESC temperature. Adjust protection thresholds in VESC_TOOL if appropriate for your setup. |
| ESC damaged after firmware upgrade | If upgrading to firmware 5.3 or above, ensure phase filtering is set to "false" in VESC_TOOL. Do not restore default parameters via the wizard. This is a critical step to prevent damage. |
7.2. Diagnostic Tools
The VESC_TOOL software provides comprehensive diagnostic features, including real-time data logging and fault code reporting. Utilize these tools to identify the root cause of any issues.
8. User Tips
- Multi-Motor Setup: For applications requiring two motors, a single FSESC75200 can control one motor. You will need a separate ESC for each motor, and they can be linked via the CAN bus for synchronized control using VESC_TOOL.
- Forward/Reverse Functionality: The ESC supports forward and reverse operation. This functionality is configured within the VESC_TOOL software during motor setup.
- Battery Compatibility: The FSESC75200 is compatible with Lithium batteries (4-20S). Ensure your battery's voltage and discharge capabilities match the ESC's requirements and your application's demands.
9. Warranty and Support
9.1. Warranty Policy
The warranty period for consumable electronic products (e.g., VESC/Motor/Battery) is 2 months starting from the 7th day after shipment (shipping date checked by logistic record). To process an after-sale service claim, contact Flipsky support at outlook.coontact@flipsky.net.
You may return the product for repair or replacement if it is not repairable. The cost of return shipping is borne by the customer. If a discount was provided for the new replacement, the shipping cost is not included.
For non-electronic products, the warranty period is 2 months from the 7th day after shipment. You can return it for free repair or replacement if it is found to be a manufacturing failure. Wear and tear caused by normal use is not considered a defect.
9.2. Warranty Exclusions
The following conditions are not covered by the above warranty:
- Purchase through unauthorized channels.
- Mechanical damage to electronic components or PCB.
- PCB board has repair soldering iron traces (excluding solder the cable bullet connectors).
- Wire damage or external impact damage.
- Water damage (for non-waterproof products).
- Abnormal applications beyond the product specifications.
- Products purchased from channels other than Flipsky.
- For products purchased not from https://flipsky.net, contact the original purchase channel first.
- Group-buy warranty: The warranty period will be processed since the 7th day after the original group-buy order's shipment. For end users, if there's any quality issue, please provide the after-sales warranty card number (which is shipped in your product package).
- Warranty is only valid once per product. If the original ordered product has been replaced under warranty, the warranty is invalid for the replacement product.
9.3. Clarification
Most products are tested before shipment. The VESC and motors are 100% tested and shipped as good products. Any uncertain connection or information for VESC/Motor settings, please contact support before installation.
No term warranty. In no case shall Flipsky's liability be greater than the actual purchase price of the product.
Repair service for reasonable charge if your product is out of warranty, while the service excludes both sides shipping cost.
This updated warranty policy is valid since 2018/11/1, and the previous orders produced before 2018/11/1 still follow the policy before updates.