YESPER YJS40

Contents

YESPER YJS40 Jump Starter User Manual

Model: YJS40

Brand: YESPER

Introduction

Thank you for choosing the YESPER YJS40 Jump Starter. This device is designed to provide reliable jump-starting for your vehicle, act as a portable power bank, and offer emergency lighting. Please read this manual carefully before use to ensure safe and optimal operation. Keep this manual for future reference.

Product Layout

Familiarize yourself with the components of your YESPER YJS40 Jump Starter:

Diagram of YESPER YJS40 Jump Starter with labeled parts
Diagram of the YESPER YJS40 Jump Starter with its various ports and indicators.
  1. Indicator Lights
  2. Power Switch
  3. 15V 10A Output Port (DC)
  4. Jump Start Socket
  5. USB 5V 2.4A Output Port
  6. Quick Charge Output Port
  7. USB-C Input/Output Port
  8. LED Flashlight

Setup

Charging the YESPER YJS40

Before first use, fully charge the device. It takes approximately 8-9 hours for a full charge via the USB-C port.

YESPER YJS40 being charged by a wall charger
The YESPER YJS40 charging via a wall adapter, showing battery level indicators.
  1. Plug a home adapter into a universal socket.
  2. Connect the USB-C input port of the YESPER YJS40 to the other end of the home adapter using the provided USB to USB-C cable.
  3. The indicator lights will flash one by one during charging. All indicators will light off when charging is paused or completed.

Operating Instructions

Checking Battery Level

Press the power switch to check the current charge level of the YESPER YJS40. The number of solid indicator lights corresponds to the storage level:

  • Unlit: 0%
  • 1 solid light: 25%
  • 2 solid lights: 50%
  • 3 solid lights: 75%
  • 4 solid lights: 100%

Jump Starting a 12V Vehicle

The YESPER YJS40 is rated at 4120-amps peak current and can jump start all 12V gasoline engines and up to 10.0-liter diesel engines.

YESPER YJS40 Jump Starter connected to a car battery
The YESPER YJS40 Jump Starter connected to a car battery, ready to start.
Three-step guide for jump starting a vehicle
Visual guide for the three steps to jump start your vehicle.
  1. Connect the blue plug of the intelligent jumper cable fully into the jump start socket on the host. Ensure the Cable Indicator is off.
  2. Connect the Red Clamp to the positive (+) battery terminal and the Black Clamp to the negative (-) battery terminal of your vehicle.
  3. Observe the Cable Indicator and follow its instructions:
    • GREEN LIGHT on: The connection is correct and the circuit is working. You can turn on the engine directly.
    • REVERSE RED LIGHT on: The connection is wrong. Correct the clamps as mentioned in step 2. Wait until the GREEN LIGHT turns on before attempting to start the engine.
    • GREEN LIGHT blinking: The vehicle's battery is low. Press the "BOOST" button. Wait until the GREEN LIGHT becomes solid, then turn on the engine within 30 seconds.
    • No Lights on: The vehicle's battery may be damaged. After confirming the clamps connection is correct, press the "BOOST" button. Wait until the GREEN LIGHT becomes solid, then turn on the engine within 30 seconds.
  4. Start the vehicle.
  5. Once the vehicle is started, remove the jumper cable from the vehicle battery. Leave the vehicle's engine running.
Watch this video for a demonstration of the YESPER YJS40 Jump Starter in action, including jump-starting a vehicle and its other functionalities.

Charging Cell Phones or Tablets

YESPER YJS40 charging multiple devices
The YESPER YJS40 can charge multiple devices simultaneously, acting as a portable power bank.
  1. Plug the appropriate charging cable into the Quick Charge output port or the USB 5V 2.4A output port.
  2. Connect the other end of the cable to your mobile phone or tablet.
  3. Press the power switch button to initiate charging.
  4. If charging does not start, try using another USB output port.

Power Supply to Vehicle Products or Electronics

YESPER YJS40 connected to an air compressor and car vacuum
The multi-function DC interface allows connection to various car accessories like air compressors and vacuum cleaners.
  1. Plug the optional switch cable (e.g., cigarette lighter adapter) into the 15V 10A output port.
  2. Connect the optional switch cable to your vehicle product or electronics (e.g., tire inflator, car vacuum cleaner, car refrigerator).
  3. Press the power switch button to supply power.

LED Flashlight

YESPER YJS40 LED flashlight in various modes
The YESPER YJS40 features a 400 lumen LED flashlight with SOS, Strobe, and normal illumination modes for emergencies and outdoor activities.

Press the power switch for 3 seconds to turn on the LED flashlight. Subsequent short presses will cycle through the following modes:

  • Normal Illumination
  • Strobe Light
  • SOS Signal Light
  • Off

Maintenance

  • **Storage:** Store the unit in a dry place where the temperature does not exceed 60°C (140°F).
  • **Charging:** Charge the unit only at ambient temperatures between 0°C (32°F) and 45°C (113°F).
  • **Recharge Frequency:** To maintain optimal performance and readiness, it is recommended to recharge the unit every 3 months, even if not in use.
  • **Cleaning:** Do not allow the product to become wet or immerse it in water. Clean with a dry cloth.
  • **Disassembly:** Do not modify or disassemble the YESPER YJS40. Only a qualified repair technician may service this unit.

Troubleshooting

TroubleReasonRemedies
It has charged for a long time, but the fourth battery indicator is still blinking.Battery power problem.Disconnect the charging cable and plug it in again, try to continue charging for hours.
No response when pressing the power switch.Low voltage protection is started.Try to charge the unit with a wall charger to activate it.
This unit cannot be charged, the first battery indicator blinks all the time.The unit is over discharged or defective.Please contact us: cs@yes-per.com
This unit is overheated or swelled.The unit is over discharged or defective.Please contact us: cs@yes-per.com

If there is any other problem with this unit, please contact us directly at cs@yes-per.com. We will do our best to solve the problem within 24 hours.

Specifications

Diagram showing product specifications and internal components
Detailed diagram of the YESPER YJS40 highlighting its internal components and specifications.
FeatureSpecification
ModelYJS40
Dimensions (L x W x H)8.82"D x 3.53"W x 1.72"H (Approx. 224 x 89.6 x 43.8 mm)
Item Weight1.71 lb (0.78 kg)
Battery Capacity26800mAh (99.16Wh)
Battery TypeLi-ion Battery / Lithium Polymer
Battery Voltage3.7 V Nominal
Number of Built-in Batteries4
Peak Current4120A
Starting Current600 A
Power Output (Jump-Start)12 V
Gas Engine RatingALL
Diesel Engine RatingUp to 10 L
Conversion Rate>90%
Output (Quick Charge)5V/2.4A; 9V/2A; 12V/1.5A (18W MAX)
Output (USB-A2)USB 5V/2.4A
Output (DC)Stable 15V/10A (150W) Supply
Input/Output (USB-C)5V/3A (15W)
Full Charge TimeAbout 8-9 Hours (Overnight)
Operating Temperature-20°C to 60°C (-4°F to 140°F)
LED ModesIllumination/SOS/Strobe
Long-Lasting Battery1000+ Charge Cycles
Long-Lasting StandbyUp to 24 Months
CertificationsCE, FCC, SDS, MSDS, ROHS, UL

Safety Information and Warnings

Always follow basic safety precautions when using electrical appliances. Failure to follow these warnings may result in electric shock, fire, and/or serious injury.

YESPER YJS40 showing 10 safety protection features
The YESPER YJS40 incorporates 10 safety protection features including overcharge, over-discharge, over-temperature, anti-charge, over-voltage, over-current, AI software, reverse polarity, short circuit, and low self-consumption protection.
  • Read the instruction manual carefully before using this unit.
  • Jump start only 12V vehicles. It would be hazardous for other jumping applications.
  • DO NOT use this unit if any cable clamp or cord is damaged.
  • DO NOT use in place of a vehicle battery.
  • Never leave the unit on the car battery after successfully cranking the car.
  • Make sure to check all battery connections are CLEAN before Jump Starting! Ensure the battery clamps are well connected! If the battery terminals on the vehicle are dirty or corroded, the power of the unit will be lessened.
  • DO NOT Jump Start more than 3 times in a row. It could damage the unit by overheating. When starting multiple times, each start-up interval should be two minutes.
  • Remove the product from the vehicle battery within 30 seconds of Jump Starting. If not, it could lead to damage.
  • DO NOT connect the two clamps together.
  • DO NOT use by young or infirm persons without supervision.
  • DO NOT use as a toy.
  • DO NOT allow the product to become wet.
  • DO NOT immerse the product in water.
  • DO NOT operate the product in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
  • DO NOT modify or disassemble the YESPER YJS40. Only a repair technician may repair this unit.
  • DO NOT expose the product to extreme heat or fire.
  • Make sure someone should be within range of your voice or close enough to come to your aid when working with batteries.
  • Remove personal metal items like rings, bracelets, necklaces, etc., when using the products.
  • DO NOT drop the unit. If the unit receives a sharp blow or is otherwise damaged in any way, have it checked by a qualified battery technician.
  • DO NOT store in locations where the temperature may exceed 60°C (140°F).
  • Charge only at ambient temperature between 0°C (32°F) and 45°C (113°F).
  • Charge only using the charger provided with this unit or one of the same standard with the host input port.
  • DO NOT use the unit to jump start a vehicle while charging the internal battery.
  • If this unit is leaking liquid, dispose of it at a proper recycle facility immediately.
  • Under extreme conditions, battery leakage can occur. If liquid is noticed coming from the product, do not handle with bare hands. In case of skin contact, wash with soap and water immediately. If liquid comes in contact with eyes, rinse eyes with cold running water for at least 10 minutes and get medical attention immediately.
  • Product contains a lithium-based battery; at the end of product life, dispose of the product according to local regulations.
  • After jump starting the car, do not charge this unit immediately.
  • DO NOT use the jumper cable to charge other equipment.

User Tips

  • **Charging Other Devices:** When using the YJS40 to charge your cell phone or other devices, consider the battery capacity of your phone to estimate the number of charges you can expect.
  • **Maintaining Readiness:** Recharge the unit every 3 months to maintain optimal performance and readiness, even if it hasn't been used. This ensures it's always prepared for an emergency.
  • **PDF Manual:** For a comprehensive user guide, including German, Russian, French, and Japanese versions, please refer to the official PDF manual available at yes-per.com/user-guide.

Warranty and Support

Warranty Information

We offer a limited warranty for this product against any defects in material and workmanship for a period of 6 months from the date of purchase by the end user/consumer. The conditions of the warranty are as follows:

  • The warranty is only valid upon presentation of the original receipt (from dealer/retailer) by the original purchaser with the product to be repaired or replaced.
  • The warranty is void if the serial number, date of purchase, and label have been removed.
  • The warranty does not cover damage or product failure resulting from normal wear and tear, physical abuse, improper installation, misuse, modification, or repairs by unauthorized third parties.
  • We do not assume responsibility for any loss or damage incurred during shipment or as a result of a force majeure.
  • We are not liable for any incidental or consequential damages arising from the use or misuse of this product.
  • All warranty claims are limited to repair or replacement of the defective product and are at our sole discretion.
  • If we repair or replace the product, the product will be covered for the remaining time of the original warranty period. Repair or replacement may involve the use of reconditioned units which are equivalent in function. Replaced parts or products become our property.
  • Consumable components such as batteries are not covered by the warranty.

After-Sales Service

We provide 12+6 Months Online After-Sales Service:

  • Within the first 12 months, we offer timely and effective online after-sales service.
  • If you register on our official store (yes-per.com) and become a member customer, you will receive an extra 6 months of service, totaling 18 months.
  • 30 Days Money Back Guarantee: Within the first 30 days after purchase, you can apply for a return through your seller if you have any issues.
  • 30 Days to 12 Months (18 Months for Member Customers): We will replace defective units due to manufacturing issues with a new one within 12 months (or 18 months for member customers).

Contact Information

For customer service, technical support, or any inquiries, please feel free to contact us:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.