1. Introduction
The RadioMaster TX12 MKII is a compact yet powerful radio control transmitter designed for various RC applications, including airplanes and drones. It features an upgraded processor, improved ergonomics, and supports both EdgeTX and OpenTX firmware. This manual provides essential information for setting up, operating, and maintaining your TX12 MKII transmitter.
2. Package Contents
Verify that all items are present in your package:
- TX12 MKII packing box * 1
- TX12 MKII remote control * 1
- QC3 USB-C charging cable * 1
- Battery case * 1
- Antenna cap * 1
- Manual * 1
- Stickers * 1
3. Product Overview
The TX12 MKII features a robust design with several improvements over its predecessor. Key features include:
- Updated rear case with comfortable ergonomic grips.
- Improved S1 / S2 slider grips for enhanced control.
- Upgraded main processor from STM32F207 to STM32F407 for better performance.
- Precision hall-effect gimbals, adjustable without disassembly.
- Native EdgeTX and OpenTX support.
- Internal ExpressLRS RF Module (available in ELRS versions).
- Standard JR module bay for external modules.
4. Setup
4.1 Battery Installation
The TX12 MKII supports dual 18650 or dual 21700 Li-ion cells, or a 2S Lipo battery up to 74x36x22mm. Ensure correct polarity when inserting batteries.
4.2 SD Card
An SD card is included with the transmitter and is essential for firmware, model memory, and sound files. Insert it into the designated slot as shown in the diagram.
4.3 Charging
The TX12 MKII features improved USB-C QC 3.0 charging. Connect the provided USB-C cable to the charging port on the bottom of the transmitter and to a compatible QC 3.0 power adapter.
4.4 Throttle Mode Configuration
The transmitter can be configured for different throttle modes:
- M2 (Mode 2): Left Hand Throttle.
- M1 (Mode 1): Right Hand Throttle.
This setting typically refers to the stick configuration for throttle control and can usually be changed in the transmitter's software settings.
4.5 Receiver Compatibility
The TX12 MKII is available with different RF chip options: ExpressLRS (ELRS) or CC2500. The choice of RF chip determines compatible receivers.
- ELRS Version: Compatible with ExpressLRS 2.4 mode receivers.
- CC2500 Version: Compatible with D16 mode receivers.
Ensure your receiver matches the RF chip option of your transmitter for proper binding and operation.
5. Operating Instructions
5.1 Power On/Off
To power on the transmitter, press and hold the power button located centrally on the control panel until the LCD screen illuminates. To power off, press and hold the power button again until the shutdown sequence completes.
5.2 Gimbal Adjustment
The precision hall-effect gimbals on the TX12 MKII are adjustable without disassembly. The adjustment range is typically between 38° and 54°. Refer to the product overview diagram for the location of adjustment points.
5.3 Firmware (EdgeTX / OpenTX)
The TX12 MKII comes with EdgeTX factory installed. It also supports OpenTX. These open-source firmware options provide extensive customization and functionality. Consult the respective firmware documentation for detailed programming and setup guides.
5.4 USB Simulator Support
The transmitter supports USB simulators, allowing you to practice flying on your computer. Connect the Data USB-C Port to your PC. The TRS 3.5mm Trainer Socket can also be used for trainer functions.
5.5 ExpressLRS BLE Joystick Mode
For ExpressLRS versions only, the TX12 MKII supports BLE (Bluetooth Low Energy) Joystick Mode. This allows for Bluetooth connection to PCs, tablets, and phones with Bluetooth functionality to play simulators and games.
6. Maintenance
6.1 General Care
- Keep the transmitter clean and free from dust and debris.
- Avoid exposing the transmitter to extreme temperatures or moisture.
- Store the transmitter in a safe place, preferably in its original packaging or a protective case, when not in use.
6.2 Firmware Upgrades
Firmware upgrades can be performed via USB/SD card using EdgeTX Buddy online or EdgeTX Companion PC software. Regularly check for updates to ensure optimal performance and access to new features.
7. Troubleshooting
7.1 RF Chip Options (CC2500 vs. ELRS)
The TX12 MKII is available with two main RF chip options: CC2500 and ExpressLRS (ELRS). The primary difference lies in the communication protocol and compatible receivers:
- CC2500: Supports multiple protocols, often compatible with FrSky D16, Futaba S-FHSS, and other legacy protocols.
- ExpressLRS (ELRS): A high-performance, open-source radio link for RC applications, known for its long range, low latency, and high refresh rates. It requires ELRS-compatible receivers.
Ensure you select the correct transmitter version and pair it with a compatible receiver.
7.2 Receiver Compatibility
As noted in the setup section, the choice of receiver depends on the RF chip in your TX12 MKII. For CC2500 versions, use receivers compatible with D16 mode. For ELRS versions, use ELRS 2.4 mode receivers. Attempting to bind incompatible receivers will result in failure to connect.
7.3 FCC vs. LBT Options
The regulatory compliance (FCC or LBT) for radio transmission can vary by region. FCC (Federal Communications Commission) is common in North America, while LBT (Listen Before Talk) is often used in Europe. The specific option shipped may depend on the region of purchase or can sometimes be configured via firmware. Users should ensure their transmitter complies with local regulations.
8. Specifications
8.1 RadioMaster TX12 MKII Transmitter
| Feature | Specification |
|---|---|
| Size | 170*159*108mm |
| Weight | 363g |
| Frequency | 2.400GHZ-2.480GHZ |
| RF Chip Option | ExpressLRS (ELRS) or CC2500 |
| Transmitting Power | 20dbm |
| Antenna Gain | 2db |
| Working Current | 320mA@8.4V |
| Voltage Range | 6.6-8.4v DC |
| Range | > 2km (depending on receiver) |
| Radio Firmware | EdgeTX (Transmitter) / ExpressLRS (RF module) |
| Channels | Up to 16 (depending on receiver) |
| Display | 128*64 Monochrome LCD display |
| Gimbal | High precision hall gimbals |
| External Module Bay | JR/FrSKY/Crossfire compatible |
| Upgrade Method | USB/SD card & EdgeTX Buddy online or EdgeTX Companion PC software |
| USB Charging | QC3 USB-C |
| SD Card | Included |
8.2 Jumper R1 V2 MINI Receiver (Optional)
| Feature | Specification |
|---|---|
| Size | 17.2*8.8*4.5mm (L*W*H) |
| Weight | 1.5g |
| Channel | 16CH |
| Operating Voltage | 3.5V-6V |
| Operating Current | 60mA@5V |
| Operating Range | Full range |
| Distance | >2KM |
| Compatibility | Radios in D16 mode |
8.3 Jumper ELRS Receiver (RX-MINI-SE) (Optional)
| Feature | Specification |
|---|---|
| Size | 17.2*8.8*4.3mm (L x W x H) |
| Weight | 1.1g |
| Channels | 16CH |
| Operating Voltage | 3.5V~6V |
| Operating Current | 60mA@5V |
| Operating Range | Full range |
| Distance | >5KM |
| Compatibility | Radios in ELRS 2.4 mode |
9. Warranty and Support
For warranty claims, technical support, or service inquiries, please contact the manufacturer or your authorized dealer. Keep your proof of purchase for warranty validation.