YIDIAN AS24M00246

Contents

YIDIAN AS24M00246 Biesse ATS Vacuum Suction Pod Instruction Manual

Model: AS24M00246 | Brand: YIDIAN

1. Introduction

This manual provides essential information for the safe and efficient use of your YIDIAN AS24M00246 Vacuum Suction Pod. This accessory is specifically designed for Biesse ATS CNC woodworking machines to securely hold workpieces during machining operations. Please read this manual thoroughly before installation and operation.

Front view of the YIDIAN AS24M00246 Vacuum Suction Pod

Figure 1: Front view of the YIDIAN AS24M00246 Vacuum Suction Pod.

2. Setup and Installation

The YIDIAN AS24M00246 Vacuum Suction Pod is designed for integration with Biesse ATS CNC machining centers. Proper installation is crucial for optimal performance and safety.

2.1 Unpacking

Carefully remove the vacuum pod from its packaging. Inspect for any signs of damage during transit. Report any damage to your supplier immediately.

2.2 Component Identification

  • Vacuum Pod Body (Black, Plastic)
  • Rubber Sealing Gasket (Pre-installed on top surface)
  • Mounting Ring (White, typically plastic, with screw holes)
  • Vacuum Connection Port (Small black button-like component on top surface)
View showing the top surface and vacuum connection port of the vacuum pod

Figure 2: Top surface with vacuum connection port.

2.3 Installation Steps

  1. Prepare the CNC Machine: Ensure the Biesse ATS CNC machine is powered off and locked out according to safety procedures. Identify the designated mounting location for the vacuum pod.
  2. Attach Mounting Ring: The vacuum pod typically uses a white circular mounting ring for attachment to the CNC machine's vacuum table or support structure. Align the mounting ring with the corresponding holes on the vacuum pod and secure it using appropriate fasteners (not included, typically provided by the CNC machine manufacturer).
  3. Position the Pod: Place the vacuum pod with the attached mounting ring onto the CNC machine's vacuum table. Ensure it is correctly seated and aligned with the vacuum ports on the machine.
  4. Connect Vacuum Line: Connect the vacuum line from the CNC machine to the vacuum connection port on the top surface of the pod. Ensure a tight, leak-free connection.
  5. Test Suction: Before placing a workpiece, power on the CNC machine and activate the vacuum system to test the suction of the pod. Listen for any leaks and ensure strong, consistent vacuum pressure.
Vacuum pod with white circular mounting ring attached

Figure 3: Vacuum pod with mounting ring for attachment.

3. Operating Instructions

The vacuum suction pod is designed to provide stable workpiece clamping for CNC machining. Follow these general operating guidelines:

  1. Workpiece Placement: Place the workpiece directly onto the rubber sealing gasket of the vacuum pod. Ensure the workpiece covers the entire sealing surface to create an effective vacuum seal.
  2. Activate Vacuum: Using the CNC machine's control panel, activate the vacuum system for the specific pod(s) in use.
  3. Verify Clamping: Visually inspect and gently attempt to move the workpiece to confirm it is securely clamped by the vacuum. Do not proceed with machining if the workpiece is not stable.
  4. Machining Operation: Perform your CNC machining operations as planned.
  5. Deactivate Vacuum: Once machining is complete, deactivate the vacuum system through the CNC machine's control panel.
  6. Remove Workpiece: Carefully remove the workpiece from the vacuum pod.

Video 1: A short demonstration of the YIDIAN Vacuum Pod, showcasing its design and various angles.

4. Maintenance

Regular maintenance ensures the longevity and optimal performance of your vacuum suction pod.

  • Cleaning: After each use, clean the rubber sealing gasket and the top surface of the pod to remove any sawdust, chips, or debris. Use a soft cloth and mild cleaning solution if necessary. Avoid abrasive cleaners.
  • Inspect Gasket: Periodically inspect the rubber sealing gasket for signs of wear, cracks, tears, or hardening. A damaged gasket can lead to vacuum leaks and reduced clamping force. Replace worn gaskets promptly.
  • Check Vacuum Port: Ensure the vacuum connection port is clear of obstructions and that the connection remains secure.
  • Storage: When not in use, store the vacuum pod in a clean, dry environment, away from direct sunlight and extreme temperatures.

5. Troubleshooting

If you encounter issues with your vacuum suction pod, refer to the following common problems and solutions:

ProblemPossible CauseSolution
Workpiece not holding securely
  • Damaged or worn rubber gasket
  • Debris on sealing surface
  • Insufficient vacuum pressure from CNC machine
  • Workpiece surface is porous or uneven
  • Loose vacuum line connection
  • Inspect and replace gasket if necessary
  • Clean sealing surface of pod and workpiece
  • Check CNC machine's vacuum pump and system
  • Use a sacrificial layer or alternative clamping for porous/uneven materials
  • Tighten vacuum line connection
Visible leaks around the pod
  • Damaged gasket
  • Improper workpiece placement
  • Loose mounting to CNC table
  • Replace gasket
  • Ensure workpiece fully covers the sealing area
  • Check mounting screws and ensure proper seating

6. Specifications

FeatureDetail
ModelAS24M00246
BrandYIDIAN
Dimensions (L x W x H)132mm x 146mm x 74mm
MaterialPlastic + Rubber
ColorBlack
WeightApproximately 2.5 kg
CompatibilityBiesse ATS CNC Woodworking Machines
Top-down view of the vacuum pod with dimensions 132mm, 146mm, and 74mm indicated

Figure 4: Dimensions of the vacuum pod.

7. User Tips

  • Always ensure the workpiece surface is clean and free of dust or oil for the best vacuum seal.
  • For optimal performance, periodically check the vacuum system of your CNC machine to ensure it's delivering adequate pressure.
  • Consider having spare rubber gaskets on hand, as they are critical wear components for vacuum pods.

8. Warranty and Support

For specific warranty information, please refer to the terms and conditions provided by your original point of purchase or contact YIDIAN customer support directly. Keep your purchase receipt as proof of purchase.

For technical support or inquiries, please contact the manufacturer or your authorized dealer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.