Flipsky FSESC75100

Contents

Flipsky FSESC75100 Speed Controller User Manual

Model: FSESC75100 | Brand: Flipsky

Introduction

This manual provides essential information for the safe and efficient operation of your Flipsky FSESC75100 Speed Controller. The FSESC75100 is an advanced electronic speed controller (ESC) designed for electric skateboards, scooters, and e-bikes, featuring an aluminum PCB for enhanced thermal performance. Please read this manual thoroughly before installation and use.

Specifications

FeatureDetail
Dimensions (L*W*H)85mm * 50.7mm * 33.8mm (18.5mm + 5.9mm USB Type)
Voltage Range14-84V (4-20S)
Continuous Current100A
Burst Current120A
BEC Output5V@1.5A
Control ModesBLDC square wave, FOC sine wave
FirmwareLatest (firmware update supported)
ERPM150000
Control Interface PortsUSB, CAN, UART
Supported SensorsABI, HALL, AS5047, AS5048A
Input Set SupportPPM, ADC, NRF, UART
Wire Size12AWG
ProgrammableYes
Regenerative CapacityYes
MaterialComposite Material (Aluminum PCB)
Recommended Age14+ years
CertificationCE, RoHS

Note: Specifications are subject to change without prior notice.

Dimensional drawing of Flipsky FSESC75100 showing length 103mm, width 58mm, height 24.5mm, and wire spacing 18.5mm.
Figure 1: FSESC75100 Dimensions

Setup and Connections

Before connecting the FSESC75100, ensure all components are powered off. Refer to the wiring diagram below for proper connections.

Detailed wiring diagram for Flipsky FSESC75100, labeling USB, PPM, CAN, SWD, COMM, UART2, HALL ports, LED indicators, and motor/battery connections. Pinouts for each port are also shown.
Figure 2: FSESC75100 Wiring Diagram

Key Connection Points:

  • Battery Connection: Connect your battery to the main power input (red for positive, black for negative) using the provided XT60 connectors.
  • Motor Connection: Connect the three motor phase wires to the corresponding outputs on the ESC.
  • USB Port: Use the USB-C port for connecting to VESC_TOOL for configuration and firmware updates.
  • PPM Port: For connecting a Pulse Position Modulation receiver (e.g., for remote control).
  • CAN Port: For communication with other VESC-compatible devices or multiple ESCs.
  • SWD Port: For debugging and advanced programming.
  • COMM Port: General communication port.
  • UART2 Port: Universal Asynchronous Receiver-Transmitter port for serial communication with external modules (e.g., Bluetooth module, GPS).
  • HALL Sensor Ports: Connect Hall sensors from your motor for sensored operation. The diagram shows pinouts for 5V, Temp, HALL1, HALL2, HALL3, and GND.
  • LED Indicators: Blue LED and Red/Green LED provide status feedback.
Close-up view of the Flipsky FSESC75100's top side, clearly showing the USB-C port, servo port, and various sensor/communication ports (CAN, SWD, COMM, UART2, HALL) with their labels.
Figure 3: Detailed View of Control Interface Ports

After all connections are made, proceed to the configuration step using VESC_TOOL.

Operating Instructions

The FSESC75100 supports both BLDC square wave mode control and FOC sine wave mode, offering flexibility for various motor types and performance requirements. It also features regenerative braking capacity, which can return energy to the battery during deceleration.

Basic Operation:

  1. Power On: Connect the battery to the ESC. The LED indicators will show the status.
  2. Configuration: Use the VESC_TOOL software to configure motor parameters, input settings (PPM, ADC, NRF, UART), and other advanced features.
  3. Motor Detection: Perform motor detection within VESC_TOOL to calibrate the ESC to your specific motor.
  4. Testing: After configuration, perform low-power tests to ensure correct motor rotation and response before full operation.

For detailed software configuration, refer to the official VESC_TOOL documentation.

Video 1: Flipsky FSESC75100 Product Overview

Maintenance

To ensure the longevity and optimal performance of your FSESC75100, follow these maintenance guidelines:

  • Keep Clean: Regularly inspect the ESC for dust, dirt, or debris. Clean with a soft, dry brush or compressed air.
  • Avoid Moisture: Protect the ESC from water and excessive humidity. While the aluminum PCB aids in heat dissipation, the unit is not waterproof unless explicitly stated or sealed by the user.
  • Check Connections: Periodically check all wire connections for looseness or damage. Secure any loose connections.
  • Temperature Monitoring: Monitor the ESC temperature during operation, especially under heavy loads. Excessive heat can reduce performance and lifespan.
  • Firmware Updates: Keep the firmware updated to the latest version to benefit from performance improvements and bug fixes. Always follow official update procedures.

Troubleshooting

Important Note on Phase Filtering:

Phase filtering is NOT available for Flipsky ESC75100 and 75200 models. If you are using firmware version 5.3 or above (VESC_TOOL 3.01 or newer), you MUST turn off the phase filter function and select "false" in VESC_TOOL. Failure to do so will result in ESC damage.

Do NOT restore default parameters when using the wizard interface if you are on firmware 5.3+ as this may re-enable phase filtering.

For more detailed information and visual guides on this issue, please refer to the following resources:

General Troubleshooting Tips:

  • No Power: Check battery connections, ensure the battery is charged, and verify main power switch (if applicable).
  • Motor Not Spinning: Re-check motor phase wire connections and Hall sensor connections. Ensure motor detection was successful in VESC_TOOL.
  • Intermittent Operation: Inspect all wiring for loose connections or damage. Check for overheating.
  • ESC Not Connecting to VESC_TOOL: Ensure the correct USB-C cable is used and drivers are installed. Try a different USB port or cable.

User Tips

No specific user tips are available from reviews or Q&A at this time. Always ensure your firmware is up-to-date and configured correctly for your specific setup.

Warranty and Support

This Flipsky product is designed for reliability and performance. For support, please contact the RCKING Store directly through the platform where you purchased the item.

Key Service Information:

  • Free Returns: Enjoy free returns within 90 days of purchase.
  • Fast Delivery Guarantee: The seller offers fast delivery with potential compensation (e.g., $1.00 coupon) if delivery is delayed. Refunds are also available if the package is lost or items are damaged during transit, or if no delivery occurs within 30 days.
  • Security & Privacy: Your personal details are protected and not shared with third parties without consent.

For detailed terms and conditions regarding these services, please refer to the official service promises provided by the seller on the product page.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.