Introduction
Thank you for choosing the Hirisi 1+1 Carp Fishing Alarm and Swinger Set. This manual provides detailed instructions for the proper setup, operation, and maintenance of your new fishing equipment. Designed for carp fishing, this set helps detect fish bites with audible and visual alerts, enhancing your fishing experience.
Package Contents
Please check the package to ensure all items are present:
- 1 x Fishing Bite Alarm
- 1 x Fishing Swinger (available in 4 colors: Red, Blue, Green, Yellow)

Key Features
Fishing Bite Alarm:
- Warning LED light for visual bite indication.
- Night light function for low-light conditions.
- Adjustable Volume (V), Tone (T), and Sensitivity (S) controls.
- High Output Speaker for clear audible alerts.
- 2.5mm jack for connecting an illuminated swinger.
- 20-second signal memory to indicate recent bites.
Fishing Swinger:
- Available in 4 colors (Red, Blue, Green, Yellow).
- Made from durable clear plastic.
- Removable tube for inserting fluorescent material.
- Adjustable plastic clips to securely hold your fishing line without damage.

Setup Instructions
1. Battery Installation (Fishing Bite Alarm)
- Locate the battery compartment on the back of the fishing bite alarm.
- Slide open the battery cover.
- Insert one 9V battery (not included) into the compartment, ensuring correct polarity (+/-).
- Close the battery cover securely.
2. Swinger Assembly
- The fishing swinger consists of a main body with a removable tube, a chain, and an attachment clip.
- If desired, you can insert a fluorescent tube (not included) into the clear plastic body of the swinger for enhanced visibility.
- Ensure the chain is securely attached to both the swinger body and the attachment clip.
- The chain length can be adjusted by carefully cutting it to your preferred length using pliers or scissors.

3. Attaching to Fishing Rod
- Screw the fishing bite alarm onto a bank stick or rod pod.
- Connect the fishing swinger to the 2.5mm jack on the fishing bite alarm.
- Place your fishing rod into the bite alarm's cradle.
- Clip your fishing line into the adjustable plastic clips of the swinger. Ensure the line is held firmly but can release easily upon a bite.

Operating Instructions
1. Power On/Off and Night Light
- To turn on the alarm, slide the power switch to the right.
- To turn on the alarm with the night light function, slide the power switch to the left.
- To activate/deactivate the automatic night light sensor, press and hold the 'V' (Volume) button for 5 seconds.

2. Adjusting Settings (Volume, Tone, Sensitivity)
- Use the 'V' button to adjust the volume level.
- Use the 'T' button to change the tone of the alarm.
- Use the 'S' button to set the sensitivity level. Higher sensitivity will detect smaller movements of the fishing line.

3. Bite Indication
When a fish bites and pulls the line, the alarm will emit an audible sound and the LED warning light will flash. The swinger will also move, providing an additional visual indication. The alarm features a 20-second signal memory, meaning the LED will continue to flash for 20 seconds after a bite, even if the line movement stops.
Maintenance
- Cleaning: Wipe the alarm and swinger with a soft, damp cloth after each use. Do not use abrasive cleaners or solvents.
- Storage: Store the set in a dry, cool place away from direct sunlight when not in use.
- Battery Replacement: If the alarm's sound or light becomes weak, replace the 9V battery. Ensure the battery compartment is sealed properly after replacement.
- Water Resistance: While designed for outdoor use, avoid submerging the alarm in water.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Alarm not turning on. | Dead or incorrectly installed battery. | Replace the 9V battery or check its polarity. |
| No sound from alarm. | Volume set too low or speaker malfunction. | Increase the volume using the 'V' button. If problem persists, contact support. |
| Alarm is too sensitive/not sensitive enough. | Sensitivity setting is incorrect for conditions. | Adjust the sensitivity using the 'S' button. |
| Swinger not moving freely. | Line clips too tight or obstruction. | Adjust the plastic clips or check for debris. |
Specifications
| Component | Detail |
|---|---|
| Type | Fish Bite Alarm / Swinger |
| Brand | Hirisi |
| Material | ABS Plastic |
| Power Source (Alarm) | 1 x 9V Battery (not included) |
| Swinger Colors | Red, Blue, Green, Yellow (as per available options) |
| Alarm Features | Adjustable Volume, Tone, Sensitivity; Night Light; 20s Signal Memory; 2.5mm Jack |
User Tips
- Always ensure the battery is correctly oriented for proper function and to prevent damage.
- Experiment with the alarm's sensitivity settings in different fishing conditions (e.g., calm water vs. windy conditions) to find the optimal level for detecting bites without false alarms.
- After fishing, especially in saltwater environments, it is recommended to wipe down both the alarm and swinger with a damp cloth to remove any salt residue and prolong their lifespan.
Warranty and Support
For any questions, technical assistance, or warranty claims, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.