1. Introduction
The Staniot SecPanel 5 H502-4G is a smart home security alarm system designed to provide comprehensive protection for your property. This kit features a 4.3-inch IPS capacitive touch screen control panel, built-in siren, and supports both 4G and WiFi connectivity for seamless integration with the Tuya Smart Life APP. It is compatible with a wide range of accessories and offers remote control capabilities, voice control via Alexa and Google Assistant, and multi-language support.
1.1 Product Highlights
- Various Installation Methods (Wall-mounted or Desktop Placement)
- 105dB Built-in Siren
- Longer Battery Life (Built-in 1500mAh lithium battery)
- 4.3-inch IPS Capacitive Touch Screen
- OTA Online Upgrade
- APP Remote Control
- Alexa & Google Assistant Voice Control
- Supports up to 200 Accessories
- Built-in 10 Languages

Figure 1: Staniot SecPanel 5 H502-4G Home Security Alarm System Kit
2. Product Overview
2.1 Security Panel Components

Figure 2: Security Panel Front and Back View with Components
Front View:
- 4.3" Touch Screen: Main interface for system control and information display.
- Microphone: For two-way communication.
- LED Indicator: Provides visual status feedback.
Back View:
- Speaker: For audio alerts and siren.
- Battery Switch: To turn the backup battery ON/OFF.
- Siren: Built-in alarm siren.
- Anti-disassembly Switch: Triggers an alarm if the panel is tampered with.
- Micro USB 5V 1A: Power input port.
- Nano SIM Slot: For 2G/4G cellular connectivity.
- Cable Clip: For cable management.
2.2 Accessories Overview
The system supports various accessories to enhance security. Below are examples of common accessories and their functions:

Figure 3: Common Accessories and their Specifications
- Wireless Keyboard K010: Input power DC5V 1.0A, Micro USB. Built-in 3.7V 500mAh lithium battery. Standby current <20µA. Emission current <15mA. Fully charged <1.5h. RFID protocol: 125KHz, 4100/4200. RFID card up to 10 can be equipped. Wireless parameters: 433MHz, eV1527. Product Size: 137.6 x 87.7 x 17.1mm.
- Remote Control R01: Battery specification: CR2032 x 1. Quiescent current: <5µA. Working current: <10mA. Working temperature: -10°C~+50°C. Wireless parameters: 433MHz, eV1.
- Smart Contact Sensor DS200: Battery specification: CR2450 x 2. Standby current: <1µA. Alarm current: <20mA. Working temperature: -10°C~+50°C. Relative humidity: <95% (no condensation). Wireless parameters: 433MHz, eV1527. Low battery alarm. Product size: 70 x 31.5 x 13.5mm (large), 70 x 11 x 13.5mm (small).
- Infrared Detector PR100: Battery specification: AA battery x 2. Standby current: <10µA. Alarm current: <15mA. Detection angle: 110°. Working temperature: -10°C~+50°C. Relative humidity: <95% (no condensation). Wireless parameters: 433MHz, eV1527. Product size: 53 x 103 x 35mm.
- Outdoor Solar Wireless Siren WSR100: Built-in battery: 3.7V/1000mAh lithium battery. Maximum output of solar panel: 5V/150mA. Standby current: <15mA. Alarm current: <350mA. Alarm volume: 120dB. Wired defense zone: 2 (Z0, Z1). Wireless defense zones: 25. Working temperature: -10°C~+50°C. Relative humidity: <95% (no condensation). Wireless parameters: 433MHz, eV1527. Product size: 265 x 190 x 60mm.
- Acoustic Strobe Siren WSR120: Power supply: DC5V 1A Type-C. Built-in battery: 3.7V/1000mAh lithium battery. Volume: 5 levels, adjustable. Alarm time: 4 options available. Receiving distance: 100 meters (open space). Working temperature: -20°C~50°C. Relative humidity: <95% (no condensation). Siren loudness: 115dB. Wireless parameters: 433MHz, eV1527. Product size: 135 x 100 x 27.4mm.
3. Specifications

Figure 4: Staniot SecPanel 5 H502-4G Specification Table
| Attribute | Value |
|---|---|
| Power Supply | DC5V 1.0A, Micro USB |
| Built-in Battery | 3.7V 1500mAh lithium battery |
| Working Power Consumption | <3W |
| Working Temperature | -10°C ~ +50°C |
| Relative Humidity | <95% (no condensation) |
| Wireless Parameters | 433MHz, eV1527 |
| Mobile Standard | 2G/4G |
| WiFi Standard | IEEE802.11b/g/n 2.4GHz |
| Product Size | 120 × 105 × 15.5mm |
| Zone Number | 200 |
| Output Number | 200 |
| Kit Configuration | Door/Window Sensor |
| Arming Type | APP |
| Video Interface | Yes |
| Display | Yes |
| Password Keyboard | Yes |
| Smart home platform | Tuya |
| Certification | CE, RoHS |
| Alarm Type | The Alarm, SMS, PSTN, GPRS, Apps Control |
| Power (W) | 100V-240V |
4. Setup Instructions
4.1 Security Panel Installation
The security panel offers versatile installation options: wall-mounted or desktop placement.
4.1.1 Wall Mount
- Install the hanging plate on the wall using screws. Ensure all screws are securely fastened and the hanging board is parallel.
- Align the hole on the back of the panel with the hanging plate and install it. For concealed wire installation, remove the bracket and cable clip.

Figure 5: Wall Mounted Installation
4.1.2 Desktop Placement
The panel comes with a stand on the back, allowing it to be directly placed on a desktop without needing wall installation. It can be placed anywhere in your home.

Figure 6: Desktop Placement
Important Notes for Panel Placement:
- Install the panel in the center of your home to optimize signal reception and transmission.
- Place it closer to your WiFi router for better connectivity.
- Avoid installing devices on metal surfaces or load-bearing walls, as this can interfere with wireless signals.
4.2 Smart Life APP Setup
4.2.1 Download the APP
Download the 'Smart Life' APP from your device's app store or by scanning the QR codes below. Ensure you grant all necessary permissions after installation.

Figure 7: Smart Life App Download QR Codes (Apple App Store and Google Play Store)
- For iOS users, scan the Apple APP QR code.
- For Android users, scan the Google Play QR code.
- After downloading, enable all usage permissions for the APP in your phone settings.
- Sign up or log in to your APP account.
4.2.2 Connect Panel to Smart Life APP
Important: This security panel only supports 2.4GHz WiFi networks. Ensure your router is configured correctly and connected to the internet. When adding the panel, enable WiFi and Bluetooth on your mobile phone and confirm it's connected to the 2.4GHz frequency band.
- Initial Setup: Connect the security panel to power and turn the backup battery switch to 'ON'. The panel will display the operation guide interface. If you are already on the main interface or need to reset WiFi, go to 'Menu' > 'Settings' > 'WiFi' and enter the default user code (1234).
- Enter Pairing Mode: On the panel, press 'Airlink' to enter WiFi pairing mode.
- Add Device in APP: Open the Smart Life APP, go to the 'Home' interface, click '+' in the upper right corner, and select 'Add Device'. The APP will discover the panel. Press 'Add' on the discovering device area, then press the '+' for 'Smart Security Panel'.
- Enter WiFi Credentials: Input your 2.4GHz WiFi network name and password, then click 'Next'.
- Pairing Confirmation: Once successfully paired, the APP will confirm.
4.2.3 APP Settings and Device Sharing
You can remotely control the alarm system via the APP. You can also share device access with family members.
- Rename Device: In the APP, navigate to the accessory's settings and edit the 'Sub device name'.
- Share Device: A security panel can be paired with one APP account, but shared with multiple family members for management.
- Other Settings: Access 'Setting' in the APP to modify security panel settings, set arm/disarm times, and more.
4.3 Adding Security Devices (Accessories)
To add accessories, ensure the security panel is in configuration mode and then trigger the accessory.
4.3.1 Entry Sensor Configuration and Installation
- Configure: On the Security Panel, go to 'Menu' > 'Accessories'. Enter the User Code (Default: 1234). Press 'Sensor' > '+' > 'Entry', then set the Mode, Delay, and Advanced settings. Press '+ Pair', then trigger the Entry sensor by separating its two parts. Rename the sensor in the APP after successful pairing.
- Installation: The entry sensor should be installed on a door or window.
- Clean the installation area on the door or window.
- Apply double-sided tape to the bottom of the sensor parts.
- Install the large transmitter and small magnet separately. Ensure the triangle marks on both parts face each other, with a distance of less than 0.6 inches (1.5 cm).
- After installation, opening the door/window should cause the indicator light to illuminate for 2 seconds, confirming successful installation.

Figure 8: Entry Sensor Installation
4.3.2 Motion Sensor Configuration and Installation
- Configure: On the Security Panel, go to 'Menu' > 'Accessories'. Enter the User Code (Default: 1234). Press 'Sensor' > '+' > 'Motion', then set the Mode, Delay, and Advanced settings. Press '+ Pair', then trigger the Motion sensor by waving your hands until the light is on. Rename the sensor in the APP after successful pairing.
- Installation:
- Recommended installation height is 79-87 inches (2.0-2.2m) above the ground.
- Install in a corner or on a flat wall, ensuring no obstacles or blind spots.
- Avoid directly facing cold/hot vents or sources.
- To prevent false alarms, ensure pets cannot get close to the sensor.

Figure 9: Motion Sensor Detection Area and Components
4.3.3 Controller (Remote Control) Configuration
- Configure: On the Security Panel, go to 'Menu' > 'Accessories'. Enter the User Code (Default: 1234). Press 'Controller' > '+', then trigger the controller by pressing any key. Rename the controller in the APP after successful pairing.
4.3.4 Multifunction Button (Doorbell/SOS) Configuration
- Doorbell Button Configuration: On the Security Panel, go to 'Menu' > 'Accessories'. Enter the User Code (Default: 1234). Press 'Doorbell' > '+', then press the doorbell button. Rename the sensor in the APP after successful pairing.
- SOS Button Configuration: On the Security Panel, go to 'Menu' > 'Accessories'. Enter the User Code (Default: 1234). Press 'Sensor' > '+' > 'Urgent', then set the Advanced setting. Press '+ Pair', then trigger the SOS button. Rename the SOS button in the APP after successful pairing.
5. Operating Instructions
5.1 Main Interface and System Status
The main interface displays the current time, date, and system status. You can quickly access 'Away', 'Home', 'Log', 'Menu', and 'Disarm' functions.

Figure 10: Security Panel Main Interface
System Status Indicators:
| Icon | Status |
|---|---|
| System is in alarm state | |
| System is armed | |
| System is disarmed | |
| Accessories low battery | |
| Door/Window opened |
5.2 Alarm Modes
The security panel offers different arming modes:
- Away: The system is fully armed. Any triggered accessory will cause an alarm.
- Home: Some areas are monitored while others are not (e.g., perimeter sensors active, indoor motion sensors inactive).
- Disarm: The system cancels monitoring. Only the SOS button or accessories set to 'Always' mode can trigger an alarm.
Accessory Modes:
- Away/Home: The accessory triggers an alarm when the panel is in 'Away' or 'Home' state. Recommended for outdoor sensors.
- Away: The accessory triggers an alarm only when the panel is in 'Away' state. Recommended for outdoor detectors.
- Always: The accessory triggers an alarm regardless of the panel's state. Recommended for gas leak or smoke detectors.
- Disabled: The accessory will not trigger an alarm.
5.3 Phone and SMS Functions
The panel supports setting emergency phone numbers for calls and SMS alerts.
- Emergency Numbers: You can set up to 5 alarm phone numbers. When an alarm is triggered, the panel will send SMS messages to these numbers and then call them one by one until an answer is received.
- SIM Card Unlock: If your SIM card requires a PIN code, you must disable it on a phone first before inserting it into the panel.
- Arm/Disarm by SMS: For firmware version 1.0.20 or above, you can send SMS commands to arm or disarm the panel. The panel will reply to confirm the command. Note: Only SMS commands from phone numbers set in the panel's 'Menu' > 'Phone' > 'Settings' will be recognized.

Figure 11: Two-way Conversation and SMS Alerts
5.4 Security Settings
Access 'Menu' > 'Security' to configure various security parameters:
- Delay: Customize countdown times for arming or alarming.
- Code:
- User Code: Default is 1234.
- System Code: Default is 9876.
- Obfuscated Code: Allows entering 5-8 digits, as long as it contains the correct 4-digit code in succession.
- Password Validity Period: After selecting, you won't need to re-enter the password within 2 minutes while the screen is on.
- Alarm:
- Local Alarm: Enable/disable alarm sound from the panel.
- Siren Alarm: Enable/disable external siren signal.
- Siren Beep: Enable/disable siren beep when arming/disarming.
- Delay Beep: Choose whether to sound a beep during arm or alarm countdown.
5.5 General Settings
Access 'Menu' > 'Settings' to configure general system parameters:
- WiFi: Connect to the APP, configure the network, or change the APP user.
- Time: Set the time and adjust the date display format.
- Audio: Adjust volume, turn on/off key beep, voice tone.
- Display: Set screen time and brightness.
- Language: Select from English, Dutch, Spanish, Russian, French, Polish, German, Italian, Portuguese, Chinese.
- Recover: Restart or reset the device.
- Clean: Activates a 1-minute screen-off mode for easy cleaning.
- Help: Access user manual, device parameters (Model, Version, IMEI, etc.).
5.6 Voice Control Integration
The system is compatible with Amazon Alexa and Google Assistant. You can arm and disarm the security system using voice commands after setting it up in the Smart Life APP and binding it with your voice assistant device.
Note: A PIN code is required when disarming the device via voice command. This PIN is preset in the Alexa/Google APP.

Figure 12: Voice Control with Alexa and Google Assistant
6. Maintenance
6.1 Battery Replacement
6.1.1 Entry Sensor Battery Replacement
The entry sensor uses CR2032 batteries (x1 for Sensor A, x2 for Sensor B). To replace:
- Lift up the cover (if already installed) or slide in the direction of the arrow to remove the back cover.
- Replace the old battery with a new CR2032 battery.
- Reattach the cover.

Figure 13: Entry Sensor Battery Replacement
6.1.2 Multifunction Button Battery Replacement
The multifunction button uses a 23A 12V Alkaline battery. To replace:
- Open the cover: Use a triangular pick to slide along the gap of the case to open it outward.
- Replace the old 23A 12V Alkaline battery.
- Close the cover: Align the top and bottom covers and press firmly until it clicks into place.
6.2 Cleaning the Touch Screen
The panel features an anti-fingerprint design. For cleaning, activate the 'Clean' mode in 'Menu' > 'Settings'. The screen will turn off for one minute, allowing for easy cleaning without accidental inputs.
7. Troubleshooting
| Failure | Reason | Solution |
|---|---|---|
| Remote control malfunction | 1. Low battery 2. Metal sheet of battery compartment is in poor contact or corroded 3. Code is not paired with the panel 4. Does not match wireless parameters of the panel | 1. Replace the battery of the same model 2. Remove rust and dirt from metal sheets 3. Re-pair with the panel 4. Purchase accessories of the same type with technical parameters |
| Door sensor failure | 1. Low battery 2. Metal sheet of battery compartment is in poor contact or corroded 3. Code is not paired with the panel 4. Does not match wireless parameters of the panel 5. Door sensor transmitter and magnet are installed too far | 1. Replace the battery of the same model 2. Remove rust and dirt from metal sheets 3. Re-pair with the panel 4. Purchase accessories of the same type with technical parameters 5. Install the door sensor transmitter and the magnet close to each other |
| Motion Detector failure | 1. Low battery 2. Metal sheet of battery compartment is in poor contact or corroded 3. Code is not paired with the panel 4. Does not match wireless parameters of the panel 5. Incorrect angle | 1. Replace the battery of the same model 2. Remove rust and dirt from metal sheets 3. Re-pair with the panel 4. Purchase accessories of the same type with technical parameters 5. Adjust the installation angle |
| Security panel does not alarm | 1. The security panel is not armed 2. Improper installation of accessories, too far away from the panel 3. The accessory code does not match the panel | 1. Arming the panel 2. Adjust the position of accessories 3. Re-pair with the panel |
| The signal distance of the panel receiving accessories becomes shorter | 1. The main power is disconnected, and the backup power is insufficient 2. There is interference from similar products nearby 3. The panel receiving module is faulty | 1. Check the power supply and restore the power supply 2. Check the source of interference and remove it 3. Contact customer service for repair |
| No emergency call was made when the alarm was triggered | 1. The panel is not armed 2. No emergency phone number is set 3. Improper installation of accessories, too far away from the panel 4. Encoding does not match | 1. Arming the panel 2. Re-set according to the instructions 3. Adjust the position of accessories 4. Re-pair with the panel |
| WiFi network configuration failed | 1. 2.4GHz WiFi is not connected 2. The current router is not compatible with quick configuration 3. Damaged WiFi module | 1. Connect to 2.4GHz WiFi 2. Adopt panel WiFi hotspot configuration mode 3. Contact customer service for repair |
| Entry opened warning is invalid | 1. Door sensor pairing error 2. The door sensor switch code does not match the panel 3. Wrong alarm type is set | 1. The door opening code needs to be paired correctly 2. The accessories are non-certified devices 3. Set the alarm type as main door alarm and window alarm |
8. User Tips & FAQ
- Power Source: The main panel has a built-in 1500mAh lithium battery for backup power, but it should generally remain connected to a 5V 1A Micro USB power supply for continuous operation. Accessories are battery-powered and require periodic battery replacement (e.g., CR2032, CR2450, 23A 12V Alkaline).
- Internet Connectivity: The system primarily functions with the Smart Life APP via 2.4GHz WiFi or 4G (with a Nano SIM card). Remote control, notifications, and voice assistant integration require internet access. Basic arm/disarm functions can be performed via SMS commands if a SIM card is installed and configured, even without internet.
- Language Support: The panel supports 10 languages: English, Dutch, Spanish, Russian, French, Polish, German, Italian, Portuguese, and Chinese. You can change the language in the system settings.
- SIM Card Usage: For 2G/4G models, a Nano SIM card can be inserted. Ensure the SIM card's PIN code is disabled before insertion to avoid issues.
- Motion Sensor & Pets: To prevent false alarms, it is recommended to install motion sensors in locations where pets cannot easily access them, as the sensors may not be fully pet-immune.
- Tuya Smart Life App: The device is fully compatible with the Tuya Smart Life app, allowing for comprehensive control and monitoring from your smartphone.
9. Warranty Rules
- Please contact our after-sales service for any failure caused by the product itself during the warranty period.
- The goods are guaranteed for one year from the date of sale, and the warranty service is only valid under normal use.
- Damage caused by the use environment not meeting the requirements of this product is not covered by the warranty.
- Product damage caused by man-made and force majeure is not covered by the warranty.
10. Hazardous Substance Declaration
| Component Name | Lead (Pb) | Mercury (Hg) | Cadmium (Cd) | Hexavalent Chromium (Cr(VI)) | Polybrominated Biphenyls (PBB) | Polybrominated Diphenyl Ethers (PBDE) |
|---|---|---|---|---|---|---|
| Metal parts | 0 | 0 | 0 | 0 | 0 | 0 |
| Plastic parts | 0 | 0 | 0 | 0 | 0 | 0 |
11. FCC Declaration
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
12. Product Video
Video: Overview of the Staniot Home Security System features and functionality.