1. Introduction
The LILYGO® T8-C3 is a compact and powerful development board designed for various IoT applications. It features the ESP32-C3 32-bit RISC-V-based MCU, offering robust Wi-Fi and Bluetooth V5.0+BLE connectivity. This board supports TF card functionality and integrates a 3D antenna for enhanced wireless performance. It is compatible with popular programming environments like Arduino and ESP-IDF, making it an ideal choice for developers and hobbyists.
This manual provides essential information for setting up, operating, and maintaining your T8-C3 development board.
2. Specifications
| Feature | Detail |
|---|---|
| MCU | ESP32-C3 32-bit, RISC-V-based MCU |
| Connectivity | Wi-Fi 2.4GHz, Bluetooth V5.0+BLE |
| Flash Memory | 4MB |
| Programming Languages | C/C++, MicroPython |
| Programming Platforms | Arduino, ESP-IDF |
| Onboard Functions | Reset Button, Battery Power Detection |
| Dimensions (LxWxH) | 63mm x 26mm x 4.5mm (Board only) |
| Weight | 10g |
| Package | Yes |
For detailed specifications and pinout, refer to the Pin Diagram section.
3. Package Contents
The standard package for the LILYGO T8-C3 Development Board includes the following items:
- 1 x LILYGO T8-C3 Development Board
- 2 x PH2.54 PIN (1*15P) headers
- 1 x JST 1.25mm 2P cable
Depending on the variant purchased, your package may also include:
- 1 x T-U2T USB to TTL Downloader (for variants without an onboard USB-to-serial chip)


4. Product Overview
4.1 Board Layout and Components
The LILYGO T8-C3 board features a compact design with essential components for development. Key features include a 3D antenna for wireless communication, a TF card slot for storage, a JST 1.25mm connector for external power (e.g., battery), and a USB Type-C port for power and data transfer.


4.2 Pin Diagram
Understanding the pinout is crucial for connecting peripherals and sensors to the T8-C3 board. The diagram below illustrates the various GPIOs, power pins, and special function pins.

Key pins include:
- GND: Ground connection.
- 3V3: 3.3V power output.
- 5V: 5V power input/output (depending on power source).
- GPIOs: General Purpose Input/Output pins (e.g., GPIO0, GPIO1, GPIO2, etc.) for connecting sensors, actuators, and other modules.
- TX0/RX0: UART (Serial) communication pins (GPIO21/GPIO20).
- ADC_CHx: Analog-to-Digital Converter channels (e.g., ADC1_CH1 on GPIO01).
- FSPI_CLK, FSPI_D, FSPI_Q, FSPI_ESO: SPI interface pins.
- BOOT: Boot mode selection pin.
- TF Card: Dedicated pins for TF card communication (CS, SCK, MISO, MOSI).
5. Setup Instructions
5.1 Powering the Board
The T8-C3 development board can be powered via its USB Type-C port using a standard USB data cable connected to a computer or a 5V power adapter. Alternatively, a battery can be connected to the JST 1.25mm 2P connector for portable applications. Ensure the battery polarity is correct before connecting.
5.2 Connecting to a Computer for Programming
To upload programs to the T8-C3, you will need to connect it to your computer. Please note that the T8-C3 board does not have an onboard USB-to-serial chip. Therefore, an external T-U2T USB to TTL downloader is required to upload programs.

Steps:
- Connect the T-U2T USB to TTL downloader to your computer's USB port.
- Connect the T-U2T downloader to the T8-C3 board's serial pins (TX, RX, GND, 3V3) as per the T-U2T's instructions and the T8-C3's pin diagram.
- Install the necessary drivers for the T-U2T downloader on your computer.
- Open your preferred programming environment (e.g., Arduino IDE, ESP-IDF).
- Select the correct board (ESP32-C3 Dev Module) and the COM port corresponding to your T-U2T downloader.
- You can now upload your code to the T8-C3 board.
5.3 TF Card Installation
To use the TF card functionality, gently insert a compatible TF (MicroSD) card into the designated slot on the board until it clicks into place. Ensure the card is inserted in the correct orientation.
6. Operating Instructions
6.1 Basic Operation
Once powered and programmed, the T8-C3 will execute the uploaded code. The ESP32-C3 MCU provides Wi-Fi and Bluetooth capabilities, allowing for a wide range of wireless applications.
- Reset Button: Press the onboard Reset button to restart the MCU and re-execute the program from the beginning.
- Battery Switch: If using battery power, ensure the battery switch is in the 'ON' position.
- TF Card: Access the TF card through your program for data logging, file storage, or other applications requiring external memory.
6.2 Wireless Connectivity (Wi-Fi & Bluetooth)
The ESP32-C3 supports both 2.4GHz Wi-Fi and Bluetooth V5.0+BLE. You can integrate these features into your projects using the respective libraries in Arduino IDE or ESP-IDF. The onboard 3D antenna provides reliable wireless communication.
- Wi-Fi: Connect to local networks, host access points, or communicate directly with other Wi-Fi devices.
- Bluetooth: Establish connections with Bluetooth-enabled devices for data exchange or control. Bluetooth Low Energy (BLE) is ideal for low-power applications.
7. Maintenance
To ensure the longevity and optimal performance of your LILYGO T8-C3 development board, follow these maintenance guidelines:
- Environmental Conditions: Keep the board in a dry environment, away from moisture, dust, and extreme temperatures.
- Handling: Handle the board by its edges to avoid touching sensitive electronic components, which can be damaged by static electricity or oils from your skin.
- Cleaning: If necessary, gently clean the board with a soft, dry brush or compressed air. Avoid using liquids or harsh chemicals.
- Storage: When not in use, store the board in an anti-static bag to protect it from electrostatic discharge.
- Firmware Updates: Periodically check the official LILYGO website or community forums for any firmware updates or bug fixes for the ESP32-C3, which can improve performance and add new features.
8. Troubleshooting
If you encounter issues with your T8-C3 board, refer to the following common troubleshooting steps:
| Problem | Possible Cause / Solution |
|---|---|
| Board does not power on. |
|
| Program upload fails. |
|
| Wi-Fi or Bluetooth connectivity issues. |
|
| TF card not detected. |
|
For more advanced troubleshooting or specific error messages, consult the ESP32-C3 documentation, Arduino ESP32 community forums, or LILYGO's official support resources.
9. User Tips
Here are some helpful tips from experienced users to enhance your experience with the LILYGO T8-C3:
- Power Supply Stability: Always use a stable 5V power supply. Unstable power can lead to erratic behavior or damage to the board.
- Wiring Checks: Before powering on, meticulously double-check all your wiring connections, especially when connecting external components, to prevent short circuits.
- Community Resources: The ESP32 and LILYGO communities are excellent resources for project ideas, code examples, and troubleshooting advice. Don't hesitate to search forums or documentation.
- Start Simple: If you're new to ESP32-C3, begin with simple "blink" or "Wi-Fi scan" examples to familiarize yourself with the programming environment and board functionality before tackling complex projects.
- Heat Management: While ESP32-C3 is generally efficient, for demanding applications, ensure adequate ventilation around the board to prevent overheating.
10. Warranty and Support
LILYGO is committed to providing quality products and support. If you encounter any issues or have questions regarding your T8-C3 development board, please refer to the following guidelines:
- Product Inquiries: For any unclear aspects about your order or the product, please contact LILYGO Official Store customer service. They will provide a satisfactory solution.
- Damaged Goods: If your package or product arrives damaged due to external force or transportation, please provide clear pictures of the logistics label, packaging, and the damaged product. LILYGO will investigate with the Logistics Service Provider and offer a corresponding solution.
- Customization & Bulk Orders: For customization requests, alternative logistics channels, bulk purchases, or any other product-related questions, feel free to contact customer service.

For the most up-to-date support information and contact details, please visit the official LILYGO website or the store where you purchased the product.