Dooya DC59C

Contents

Dooya DC59C Single Channel Mechanic Wall Switch Receiver User Manual

Model: DC59C

1. Introduction

The Dooya DC59C is a single-channel mechanic wall switch receiver designed for controlling tubular motors, commonly used in roller shutters, blinds, and other automated window treatments. This manual provides essential information for the safe installation, operation, and maintenance of your DC59C switch.

Front view of the Dooya DC59C single channel mechanic wall switch

Figure 1: Front view of the Dooya DC59C switch.

2. Safety Information

WARNING: Risk of electric shock. Installation should only be performed by a qualified electrician in accordance with local electrical codes and regulations.

  • Always disconnect power at the circuit breaker before installing or servicing the switch.
  • Ensure all wiring connections are secure and properly insulated.
  • Do not expose the device to moisture or extreme temperatures outside its specified operating range.
  • This device is intended for indoor use only.

3. Package Contents

Please check the package for the following items:

  • 1 x Dooya DC59C Single Channel Mechanic Wall Switch Receiver

If any items are missing or damaged, please contact your supplier.

4. Specifications

FeatureDetail
ModelDC59C
TypeSingle Channel Mechanic Wall Switch Receiver
CompatibilityTubular Motor Emitter
Dimensions86 x 86 mm
Operating Temperature20°C to +55°C
CertificationCE
Internal Model NumberILCSDOOYREMOTECTRL08
Side view of the Dooya DC59C switch, illustrating its dimensions (86x86mm) and operating temperature range (20°C to 55°C)

Figure 2: Side view with key specifications.

5. Installation

Before proceeding with installation, ensure the main power supply to the circuit is turned OFF at the breaker.

  1. Prepare the Wall Box: Ensure you have a standard 86x86mm wall box installed at the desired location.
  2. Identify Wires: Identify the Live (L), Neutral (N), Motor Up, Motor Down, and Ground (Earth) wires from your electrical supply and tubular motor.
  3. Wiring Connections: Refer to the wiring diagram below and connect the wires to the corresponding terminals on the back of the DC59C switch. Secure each wire firmly with the screw terminals.
Rear view of the Dooya DC59C switch, showing the wiring terminals for Live (L), Neutral (N), Motor Up, Motor Down, and Ground (Earth)

Figure 3: Rear view and wiring terminals. Connect L (Live), N (Neutral), Up (Motor Up), Down (Motor Down), and Ground (Earth) wires.

  1. Mount the Switch: Carefully place the wired switch into the wall box and secure it with the mounting screws.
  2. Attach Faceplate: Snap the decorative faceplate onto the switch.
  3. Restore Power: Turn the main power supply back ON at the circuit breaker.

6. Operation

The Dooya DC59C switch features three distinct buttons for controlling your tubular motor:

  • Up Button (Top): Press this button to raise the roller shutter or blind.
  • Stop/Pause Button (Middle): Press this button to stop the motor at its current position.
  • Down Button (Bottom): Press this button to lower the roller shutter or blind.

The switch provides direct mechanical control over the motor's movement.

7. Maintenance

  • Cleaning: To clean the switch, gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as this may damage the device or cause an electrical hazard.
  • Inspection: Periodically check the switch for any signs of damage or loose connections. If any issues are found, disconnect power and consult a qualified technician.

8. Troubleshooting

ProblemPossible CauseSolution
Motor does not respond to switch.No power to the switch.
Loose wiring connections.
Motor malfunction.
Check circuit breaker.
Verify all wiring connections are secure (power off first!).
Test motor independently if possible.
Motor moves in the wrong direction.Up/Down motor wires are reversed.Disconnect power and swap the Motor Up and Motor Down wires at the switch terminals.
Switch buttons feel stiff or unresponsive.Dust or debris accumulation.
Internal mechanical issue.
Gently clean the switch surface.
If problem persists, consider replacement.

9. User Tips

  • For optimal performance, ensure the switch is installed in a location free from direct sunlight and excessive humidity.
  • If controlling multiple motors, ensure each motor has its own dedicated single-channel switch or a multi-channel control system designed for such applications.

10. Warranty and Support

For warranty information or technical support, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.