MESTEK ST05 Series

Contents

MESTEK ST05 Series Socket Tester User Manual

Models: ST05D (EU Plug), ST05E (UK Plug), ST05B (US Plug)

1. Introduction

The MESTEK ST05 Series Socket Tester is designed for quick and accurate detection of three-hole power socket wiring polarity and the protection function of leakage switches (RCD). It helps identify wiring conditions that could lead to electric shocks, electrical fires, or abnormal equipment operation. This device is widely used in fire protection, safety supervision, home improvement, laboratory, factory, and home line inspection and maintenance.

Warning: Please read this instruction manual carefully before use, and strictly adhere to the safety rules, cautions, and warnings provided. Failure to do so may result in electric shock or personal injury.

2. Safety Precautions

  • Before each use, carefully inspect the tester for any damage. If damage is found, discontinue use immediately and send it for repair.
  • To verify the tester's accuracy, plug it into a known correctly wired socket and confirm its test function is correct before proceeding with other tests.
  • When performing switch detection, ensure the wiring is correct for normal operation.
  • Before testing the leakage switch (RCD), turn off all equipment connected to the power line to prevent power outages from causing harm. If testing in public areas, ensure prior approval is obtained.
  • If a socket wiring error is detected, consult a professional electrician for repair.

3. Panel Introduction

The MESTEK ST05 Socket Tester features a clear VA color display screen, providing easy readability even in dark environments. Below is a diagram illustrating the various components and indicators on the device panel.

Diagram of MESTEK ST05D Socket Tester panel with numbered labels
Figure 1: MESTEK ST05D Panel Layout
  1. Low battery indication
  2. Socket pin indication
  3. Zero-live voltage test value display
  4. Power on/off button
  5. RCD leakage current test button
  6. Warning symbol
  7. Zero-earth voltage test value display
  8. Socket wiring status display area

4. Setup

4.1. Battery Installation

The MESTEK ST05 Series Socket Tester requires two AAA batteries (not included) for operation. To install the batteries:

  1. Locate the battery cover on the back of the device.
  2. Open the battery cover.
  3. Insert two AAA batteries, ensuring correct polarity (+/-).
  4. Close the battery cover securely.
Images showing battery installation, powering on, and plugging in the socket tester
Figure 2: Battery Installation and Initial Operation

4.2. Powering On

After installing the batteries, long-press the power button (ON/OFF) for 2 seconds to turn on the device.

5. Operating Instructions

5.1. Socket Wiring and Voltage Measurement

To test the current socket line status and voltage:

  1. Plug the MESTEK ST05 Socket Tester directly into the three-hole socket you wish to test.
  2. The device will automatically display the wiring status and voltage readings on its VA color screen.
MESTEK ST05D showing Live and Neutral voltage (L-N) and Neutral and Earth voltage (N-E)
Figure 3: Voltage Measurement Display

5.2. RCD Test (Residual Current Device)

Warning: Before performing the RCD test, ensure all electrical appliances connected to the circuit are turned off and that you have permission to proceed, to prevent any unintended power outages or harm.

  1. Insert the tester into the three-hole socket.
  2. Ensure the display indicates "The wiring is correct".
  3. Press the RCD button for less than 3 seconds.
  4. A properly functioning leakage switch (RCD) should trip, indicating it is working correctly. If the RCD does not trip, it indicates a failure or absence of the leakage switch. Seek professional electrician maintenance immediately.
MESTEK ST05D showing RCD test button and warning
Figure 4: RCD Test Procedure

6. Test Status Analysis

The MESTEK ST05 Socket Tester provides clear indications for various wiring conditions. Refer to the display area (8) on the panel for the detected status.

Multiple MESTEK ST05D displays showing different wiring statuses: correct, missing zero line, missing ground, fire ground reverse, fire zero reverse, mismatch and lack of land
Figure 5: Various Wiring Status Indications
  • **The wiring is correct:** All indicators show correct wiring.
  • **Missing zero line:** The zero line indicator flashes, and an alarm may sound.
  • **Missing ground:** The ground pin indicator flashes, and the zero line voltage may not be displayed.
  • **Fire ground reverse:** The live and ground pins flash, and the zero-fire voltage may be displayed as "OL".
  • **Fire zero reverse:** The neutral and live pins flash, and the neutral-ground voltage may be displayed as "OL".
  • **Mismatch and lack of land:** The live and ground pins flash, and the socket voltage may not be displayed.

7. Troubleshooting

7.1. Voltage Measurement Anomalies

  • **Zero-fire line voltage too high or too low:** The normal voltage range for the zero-fire line is ±10% of the local standard voltage. If the reading is outside this range, it may indicate that the circuit load is too high or the power supply is either too low or too high.
  • **Zero-earth wire voltage too high:** The normal voltage of the zero-earth wire should be less than 2V. If it is too high, it could be due to current leakage, an imbalance in the three-phase sequence, or signal interference in the circuit.

7.2. Wiring Errors

If the tester indicates any wiring errors (e.g., missing zero line, missing ground, fire ground reverse, fire zero reverse, mismatch and lack of land), it is crucial to have a professional electrician inspect and repair the wiring before using the socket.

8. Technical Specifications

Table of MESTEK ST05D Technical Parameters
Figure 6: Technical Parameters
ParameterValue
Zero-live voltage measure (L-N)30-250V / (50-60HZ)
Zero-earth voltage measure (N-E)0.1-10V / (50-60HZ)
Working environmentTemp 0-40°C / humidity (20%-70%)
Storage environmentTemp 10-50°C / humidity (20%-80%)
RCD Current>30mA
RCD Working voltage220V ± 20V
BatteryAAA * 2 battery (not included)
Weight106.8g

9. Maintenance

9.1. Battery Replacement

To prevent electric shock or injury due to incorrect readings, replace the batteries immediately when the low battery symbol appears on the meter. Always turn off the power and ensure the socket tester is removed from the measurement circuit before opening the battery cover to replace new batteries.

10. User Tips

  • Always ensure the correct plug type (EU, UK, or US) is used for the corresponding socket.
  • For accurate readings, ensure the socket is clean and free from debris before inserting the tester.
  • The device is designed for quick checks; for complex electrical issues, always consult a certified electrician.

11. Warranty and Support

11.1. Product Accessories

The product package typically includes:

  • Socket tester
  • Packing box
  • User manual
MESTEK ST05D Socket Tester with its packaging box and user manual
Figure 7: Product Accessories

11.2. Warranty Information

This product is guaranteed for 18 months from the date of purchase. The warranty does not cover fuses, disposable batteries, packaging, or damage to the instrument due to accidents, neglect, abuse, alterations, pollution, or abnormal operating conditions.

This manual is subject to change without notice. While the contents are considered correct, please contact Shenzhen Mestek Electronics Co., LTD if you find any errors.

The company is not responsible for accidents or hazards caused by incorrect user operation. The functions described in this manual should not be used as a basis for using the product for special purposes.

11.3. Manufacturer Information

Shenzhen Mestek Electronics Co.,LTD
Address: [Address not provided]
Hotline: [Hotline not provided]

12. Product Overview Video

Watch this video for a visual demonstration of the MESTEK ST05 Socket Tester, including its different plug types, battery installation, and basic operation.

Video: MESTEK ST05 Socket Tester demonstration.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.