PHYEE 20P2ISO

Contents

PHYEE 20 Pin to ISO Wiring Harness Adapter Instruction Manual

Model: 20P2ISO

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your PHYEE 20 Pin to ISO Wiring Harness Adapter. This adapter is designed to facilitate the connection of aftermarket car radios with a 20-pin socket to vehicles equipped with an ISO plug, ensuring a seamless and reliable electrical connection.

PHYEE 20 Pin to ISO Wiring Harness Adapter

Image: The PHYEE 20 Pin to ISO Wiring Harness Adapter, showing the 20-pin male plug and the ISO female connector.

Setup and Installation

Important Notice: The car radio model and model year must match the harness adapter for proper functionality. This adapter is designed for car radios with a 20-pin socket and vehicles with an ISO plug.

  1. Identify Car Radio Connector: Locate the 20-pin socket on the back of your aftermarket car radio head unit.Rear of car radio with 20 Pin Connector

    Image: Rear view of a car radio highlighting the 20-pin connector socket.

  2. Connect 20-Pin Plug: Insert the 20-pin male plug of the harness adapter into the corresponding 20-pin socket on your car radio. Ensure a secure and firm connection.20 Pin socket on car radio with harness connected

    Image: Close-up of the 20-pin harness plug inserted into the car radio's socket.

  3. Connect ISO Connector: Connect the ISO 10487 female connector of the harness adapter to the ISO plug in your vehicle's wiring system. This is a standard connection for many car models.ISO 10487 Female Connector

    Image: The ISO 10487 female connector, ready for connection to the vehicle's ISO plug.

  4. Wiring Diagram Reference: Refer to the detailed wiring diagram below for specific wire functions. This diagram illustrates the connections for speakers, power (ACC, BAT, GND), steering wheel control, illumination, auto antenna, camera control, and brake detection.Detailed 18-wire diagram with pin numbers and functions

    Image: Comprehensive wiring diagram showing 18 wires, their colors, pin numbers, and corresponding functions for car radio integration, including connections for steering wheel control, speakers, power, and accessories.

    Key Wire Functions:

    • Power:
      • ACC (Ignition Switch +12V)
      • BAT (Constant Power Supply +12V)
      • GND (Ground Wire B-)
    • Speakers: Front Right (+/-), Front Left (+/-), Rear Right (+/-), Rear Left (+/-)
    • Steering Wheel Control: KEY1, KEY2, KEY-GND (These wires are typically not part of the standard ISO connector and may require separate connection to your vehicle's steering wheel control module.)
    • Other Functions:
      • REVERSE (Reversing detection)
      • ILL (Illuminate Backlight)
      • PARKING (Parking Sensor Control Wires)
      • ANT (Auto Antenna Power)
    Close-up of ISO connector pins with labels

    Image: Close-up view of the ISO connector pins, indicating the positions for speakers, ACC (+12V), GND (Ground), and car battery (+12V).

  5. Final Connection: Once all connections are made, ensure they are secure before powering on the car radio.Full view of harness connected to car radio

    Image: The complete harness adapter connected to the car radio, ready for installation into the vehicle.

Operating Instructions

The PHYEE 20 Pin to ISO Wiring Harness Adapter is a passive component designed to facilitate electrical connections. Once correctly installed, its operation is integrated with your car radio and vehicle's electrical system.

  • Ensure all connections are firm and correctly matched according to the wiring diagram.
  • Power on your car radio and test all functions, including audio output, steering wheel controls (if connected), illumination, and any other integrated features.
  • If any functions are not working as expected, refer to the Troubleshooting section.

Maintenance

The wiring harness adapter requires minimal maintenance. Follow these guidelines to ensure its longevity and reliable performance:

  • Keep Dry: Avoid exposing the adapter to moisture or liquids, which can cause short circuits or corrosion.
  • Temperature: Do not expose the adapter to extreme temperatures, as this can degrade the wire insulation and plastic connectors.
  • Connection Checks: Periodically check the connections to ensure they remain secure and free from corrosion or damage.
  • Cleaning: If necessary, gently clean the connectors with a dry, lint-free cloth. Do not use harsh chemicals.

Troubleshooting

ProblemPossible CauseSolution
Car radio loses settings after installation.Some ISO connectors may have swapped functions for pin A4 (constant power) and pin A7 (ignition switch).Check your car radio's wiring diagram and the vehicle's wiring. You may need to manually swap the A4 and A7 wires on the harness if they are incorrectly configured for your specific radio/vehicle.
Harness adapter does not fit the car radio.The car radio connector is not a 20-pin type.This harness adapter is specifically designed for car radios with a 20-pin socket. Verify your car radio's connector type.
Steering wheel controls are not functioning.Steering wheel control wires (KEY1, KEY2, KEY-GND) are not connected or are incorrectly connected.These wires are typically separate from the main ISO connector. Refer to the wiring diagram and connect them to your car's steering wheel control function wires as required. Ensure your car radio supports external steering wheel control input.
No power to the car radio.Incorrect power wire connection (ACC, BAT, GND) or blown fuse.Verify that the ACC (+12V), BAT (+12V constant), and GND (Ground) wires are correctly connected according to the wiring diagram. Check the fuse on the harness adapter and your vehicle's fuse box.

Specifications

FeatureDetail
Brand NamePHYEE
Model Name20P2ISO
Item TypeCables, Adapters & Sockets
Voltage12 V
MaterialCopper
Connectors20 Pin Male Plug, ISO 10487 Female Connector
Item Weight0.08 kg
Item SizeNormal
OriginMainland China
Package Dimensions (L x W x H)10 cm x 12 cm x 4 cm

User Tips

  • Always double-check the compatibility of this harness adapter with your specific car radio model and vehicle's wiring system before installation.
  • If your car radio loses settings after installation, it might be due to swapped constant power (A4) and ignition switch (A7) wires. Consult the wiring diagram and your car radio's manual for potential adjustments.
  • For steering wheel control functionality, remember that the KEY1, KEY2, and KEY-GND wires need to be connected separately to your car's steering wheel control module, as they are not part of the standard ISO block.
  • Ensure all connections are secure to prevent intermittent issues or loss of functionality.

Warranty and Support

This PHYEE product is manufactured to high-quality standards. For any technical assistance or support, please contact the PHYEE Official Store where you purchased the product. Ensure you have your product model (20P2ISO) and purchase details available when seeking support.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.