Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your PHYEE 20 Pin to ISO Harness Adapter. This adapter is designed to facilitate the connection of an aftermarket car radio head unit equipped with a 20-pin socket to a vehicle that utilizes a standard ISO plug for its audio system. Please read this manual thoroughly before installation to ensure correct usage and optimal performance.

Figure 1: PHYEE 20 Pin to ISO Harness Adapter
Specifications
| Attribute | Value |
|---|---|
| Model Name | 20P2ISO |
| Item Type | Cables, Adapters & Sockets |
| Voltage | 12 V |
| Material | Copper |
| Item Weight | 0.08kg |
| Item Size | 20 Pin to ISO Harness Adapter |
| 20 Pin Plug | Yes |
| ISO Female Connector | Yes |
| Suitable for | Car models with ISO connector |
| High-concerned chemical | None |
Package Contents
- 1 x PHYEE 20 Pin to ISO Harness Adapter
Setup and Installation
The PHYEE 20 Pin to ISO Harness Adapter is designed for plug-and-play installation, simplifying the process of connecting your aftermarket car radio. However, professional installation is recommended to ensure proper wiring and avoid damage to your vehicle's electrical system or the car radio.
Compatibility Notice
NOTICE: The car radio model and model year must match the harness adapter for proper function.
Installation Steps
- Identify Connectors: Locate the 20-pin socket on the back of your aftermarket car radio head unit and the ISO plug in your vehicle's dashboard.
- Connect to Head Unit: Plug the 20-pin male connector of the harness adapter into the corresponding 20-pin socket on your car radio.
- Connect to Vehicle: Plug the ISO female connector of the harness adapter into the vehicle's existing ISO male plug.
- Additional Connections (if applicable): Some functions like steering wheel control, auto antenna, camera control, and brake detection require separate wire connections. Refer to the detailed wiring diagram below and your car radio's manual for specific instructions.

Figure 2: Rear view of car radio showing 20 Pin Connector

Figure 3: 20 Pin plug connecting to car radio

Figure 4: ISO Female Connector for vehicle connection
Wiring Diagram
The following diagram illustrates the pin assignments and wire functions for the PHYEE 20 Pin to ISO Harness Adapter. Ensure all connections are secure and correctly matched to your vehicle's wiring and car radio's requirements.

Figure 5: Detailed Wiring Diagram
Wire Functions:
- Brown/Black: KEY2 (Steering Wheel Control)
- Orange/Black: KEY1 (Steering Wheel Control)
- Black: REVERSE (Reversing detection)
- Orange: KEY-GND (Steering Wheel Control Ground)
- Pink: ILL (Illuminate Backlight)
- Gray/Black: PARKING (Parking Sensor Control Wires)
- Red: ACC (Ignition Switch +12V)
- Blue: ANT (Auto Antenna Power)
- Yellow: B+ (Constant Power Supply +12V)
- Black: GND (Ground Wire B-)
- Gray: Front Right Speaker +
- Gray/Black: Front Right Speaker -
- White: Front Left Speaker +
- White/Black: Front Left Speaker -
- Purple: Rear Right Speaker +
- Purple/Black: Rear Right Speaker -
- Green: Rear Left Speaker +
- Green/Black: Rear Left Speaker -
Installation Video
Watch this video for a visual guide on connecting the harness adapter to a car radio.
Video 1: Demonstration of connecting the 20 Pin to ISO Harness Adapter
Operating Instructions
Once correctly installed, the PHYEE 20 Pin to ISO Harness Adapter functions passively to enable the electrical connection between your car radio and the vehicle's wiring system. No direct operation of the adapter is required. Ensure your car radio is powered on and configured according to its own instruction manual.
Maintenance
The harness adapter requires minimal maintenance. Ensure that all connections remain secure and free from moisture or physical damage. Periodically check the wiring for any signs of wear or corrosion, especially if you experience intermittent issues with your car audio system.
Troubleshooting
- Car Radio Loses Settings: If your car radio loses its settings (e.g., station presets, clock) after installation or when the car is turned off, it may be due to an incorrect power connection. Some ISO connectors might swap the functions of the A4 (constant +12V) and A7 (switched +12V ACC) wires. Consult your car radio's manual and the vehicle's wiring diagram to verify and potentially re-pin these connections if necessary.
- No Power to Car Radio: Check the fuse on the harness adapter and ensure it is intact. Verify that the constant +12V (Yellow wire) and switched +12V ACC (Red wire) are receiving power from the vehicle.
- No Sound from Speakers: Confirm that the speaker wires (Gray, White, Purple, Green and their black-striped counterparts) are correctly connected to the car radio and the vehicle's speakers. Ensure the car radio's volume is up and not muted.
- Steering Wheel Controls Not Working: Ensure the KEY1, KEY2, and KEY-GND wires from the adapter are correctly connected to your vehicle's steering wheel control interface, if applicable. This usually requires manual connection as these wires are not part of the standard ISO block.
User Tips
- Verify Pin Assignments: Before finalizing installation, especially if you encounter issues with settings retention, double-check the pin assignments for constant power (B+) and accessory power (ACC) on both your car radio and the vehicle's wiring. Some manufacturers may vary.
- Secure Loose Wires: For any wires not used (e.g., if your car does not have steering wheel controls), ensure they are properly insulated and secured to prevent short circuits.
Warranty and Support
This PHYEE product comes with a 1-year warranty from the date of purchase, covering manufacturing defects. For technical support or warranty claims, please contact your retailer or the manufacturer directly. Keep your proof of purchase for warranty validation.