1. Introduction
Thank you for choosing Aamasun COB LED Strip Lights. These high-density, flexible LED strips provide soft, uniform illumination without visible light spots, making them ideal for various indoor decorative and functional lighting applications. This manual provides essential information for the safe and effective installation, operation, and maintenance of your LED strip lights.

2. Safety Information
- Ensure the input voltage matches the strip's rated voltage (DC12V or DC24V). Connecting to an incorrect voltage can damage the product and pose a safety risk.
- Do not connect the LED strip directly to AC power. A compatible DC power adapter (not included) is required.
- Avoid bending the strip sharply or at angles less than 90 degrees to prevent damage to the internal circuitry.
- Do not operate the strip in temperatures outside the specified operating range.
- This product is not waterproof. Avoid exposure to water or high humidity.
- Keep out of reach of children.
3. Setup and Installation
- Unpacking: Carefully remove the LED strip from its packaging. Inspect for any visible damage.
- Planning: Determine the desired length and placement for your LED strip. Measure accurately.
- Cutting (if necessary): The LED strip can be cut at designated points, typically every 50mm. These points are marked on the strip. Ensure cuts are clean and precise. The remaining sections of the strip will function normally.
- Mounting: The LED strip features double-sided tape on its back for easy installation. Clean the mounting surface thoroughly to ensure it is dry, smooth, and free of dust or grease. Peel off the protective backing from the tape and firmly press the strip onto the desired surface.
- Wiring: The COB LED strip comes with two wires or a DC female connector at the end. Connect these to a compatible DC12V or DC24V power adapter (not included). Ensure correct polarity (positive to positive, negative to negative).

4. Operating Instructions
Once properly installed and connected to a compatible power adapter, your Aamasun COB LED Strip Lights will illuminate. The strip lights are designed for continuous operation ('Always On').
- Color Temperature: The strip lights are available in three color temperatures: Warm White (3000K-3500K), Natural White (4000K-4500K), and Cool White (6000K-6500K). The chosen color temperature will be fixed for the specific strip purchased.
- Dimmability: While the COB LED strip itself is designed to be dimmable, a separate compatible dimmer switch (not included) is required to adjust the light intensity. Ensure any dimmer used is compatible with DC12V or DC24V LED strips.


5. Maintenance
- Cleaning: To clean the LED strip, gently wipe it with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the strip. Ensure the strip is powered off and cool before cleaning.
- Storage: If storing the LED strip for an extended period, ensure it is kept in a dry environment within the specified storage temperature range of -20℃ to +60℃. Avoid direct sunlight and extreme temperatures.
6. Troubleshooting
- Strip does not light up:
- Check if the power adapter is correctly connected and receiving power.
- Verify that the LED strip is connected to the power adapter with the correct polarity.
- Ensure the power adapter's output voltage matches the strip's requirement (12V or 24V).
- If the strip has been cut, ensure the connections at the cut points are secure and properly insulated. - Uneven lighting or flickering:
- Check for loose connections.
- Ensure the power adapter is sufficient for the length of the strip being used. - Strip is hot to the touch:
- While COB LEDs are efficient, some heat is normal. However, excessive heat may indicate an issue with the power supply or improper installation. Ensure adequate ventilation around the strip.
7. Specifications
| Feature | Specification |
|---|---|
| Product Name | COB soft light strip |
| Input Voltage | DC12V / 24V |
| PCB Width | 8mm |
| LED Quantity | 320 LEDs/M |
| Cutting Length | Every 50mm |
| Color Temperature | Warm White (3000K-3500K), Natural White (4000K-4500K), Cool White (6000K-6500K) |
| Color Rendering Index (CRI) | Ra>90 |
| Beam Angle | 180° |
| Operation Temperature | -20℃ to +45℃ |
| Storage Temperature | -20℃ to +60℃ |
| Power Consumption (W/m) | ~11.52W/m (approx. 12W/m for 12V/24V) |
| Average Life (hrs) | 10000 |
| Waterproof | No |
| Power Generation | Always On |
| Is Smart Device | No |
| Certification | CE, EMC, ROHS |


8. User Tips
- Power Adapter: Remember that the product link only sells the COB LED strip itself (with 2 wires or a DC female connector). A separate power adapter is required and not included in the package. Ensure you purchase a compatible 12V or 24V DC power supply with sufficient wattage for your strip length.
- Longer Strips: If ordering a 10-meter length, it typically comes as a single continuous piece, not two 5-meter sections.
- Dimmability: To achieve dimming functionality, you will need to integrate an external dimmer switch that is compatible with the strip's voltage (12V or 24V DC).
- Flexibility: The COB LED strips are designed to be soft and bendable, allowing for versatile installation in various shapes and around corners.
9. Warranty and Support
For warranty information, technical support, or any product-related inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.