1. Product Overview
The Dooya DC71 Receiver and DC70 Emitter form a wireless control system designed for motorized tubular motors, commonly used in rolling shutters, garage doors, and similar applications. This system allows for convenient remote operation of your motor.

Figure 1: Dooya DC71 Receiver and DC70 Emitters
The system includes one DC71 receiver and typically two DC70 remote emitters (remote controls).
2. Specifications
| Attribute | Value |
|---|---|
| Model Number | Dooya DC71 |
| Voltage | 110-240V |
| Wattage | 0.03W |
| Max Output Power | 500W |
| Emission Frequency | 433.92MHz |
| Certification | CE |
| EU LVD Voltage | Low voltage: Below 50Vac or 75Vdc |
| Remote Battery Included | No |
| Origin | Mainland China |
| Package Weight | 0.45 kg |
| Package Dimensions | 15cm x 15cm x 15cm |
3. Setup Instructions
Important Note: All function settings and button operations must have an interval of less than 6 seconds.
3.1. Wiring Diagram
Before connecting the receiver, ensure the power is off. The following diagram illustrates a typical installation for a motorized rolling shutter door system. Consult a qualified electrician if you are unsure about the wiring process.

Figure 2: Typical System Wiring Diagram
The diagram shows the connection of the tubular motor (DM45M-50/12) to the receiver (DC136) which is then powered. A mini single-channel emitter (DC115A) is shown for control. Other components like motor bracket (DZ198), drive adapter (DL210), driving tube, wall bracket (DZ193), idler (DW12), metal roller sheet, guiding track, hand crank (DS15, DS38), and crown (DH90) are also indicated as part of a complete system.
3.2. Pairing the Remote Emitter (Adding Code)
This process links your DC70 remote control to the DC71 receiver.

Figure 3: DC71 Receiver Controls
The DC71 receiver has three control buttons: Up, Stop, and Down.
- Connect the motor to the receiver and then plug the receiver into a power outlet.
- On the receiver, press and hold the Stop button for approximately 5 seconds. The green indicator light on the receiver will turn on and stay lit.
- While the green light is steady, press the Up button on your DC70 remote emitter once. The green light on the receiver will flash four times, indicating successful pairing.
- To test, press the Up button on the remote again. The motor should move. If it moves in the wrong direction, proceed to the "Direction Change" section.
Visual Guide: For a visual demonstration of a similar pairing process, please refer to the official instruction video below (0:22 mark). Note that button labels may vary slightly.
Video 1: Dooya Control System Setup Guide (Pairing starts at 0:22)
4. Operating Instructions
4.1. Basic Operation with Remote Emitter
The DC70 remote emitter typically has four buttons:
- Up Arrow: Moves the motor upwards (opens the shutter/door).
- Down Arrow: Moves the motor downwards (closes the shutter/door).
- Square/Stop: Stops the motor.
- Lock/Unlock: May be used for locking/unlocking the motor or other functions depending on the motor model.

Figure 4: DC70 Remote Emitter
4.2. Direction Change (Reversing Motor Direction)
If the motor moves in the opposite direction to what is intended (e.g., pressing 'Up' makes it go down), you can reverse its direction:
- Simultaneously press and hold both the Up button and the Stop button on the receiver for about 2 seconds.
- The green indicator light on the receiver will stay on, then flash. This indicates the direction change is successful.
- To verify, press the Up button on the remote emitter again. The motor should now rotate in the opposite direction.
Visual Guide: For a visual demonstration of a similar direction change process, please refer to the official instruction video below (0:52 mark). Note that button labels or methods may vary slightly.
4.3. Obstacle Rebound Function (Open/Close Setting)
The receiver supports an obstacle rebound function, which can be enabled or disabled. This feature causes the motor to reverse direction if it encounters an obstacle during closing, preventing damage or injury.

Figure 5: Obstacle Rebound Function Comparison (A: Enabled, B: Disabled)
To toggle this function (based on a similar model, exact button/sequence may vary for DC71):
- Press and hold the Stop button on the receiver.
- The green indicator light will stay on for 2 seconds, then turn off.
- After it turns off, the green light will flash once or twice.
- One flash: Obstacle rebound is enabled (default setting).
- Two flashes: Obstacle rebound is disabled.
- Release the button after the desired number of flashes to set the function.
Visual Guide: For a visual demonstration of setting the obstacle rebound function, please refer to the official instruction video below (1:13 mark). Note that button labels or methods may vary slightly.