JYX C30/C40 48V 500W/1000W Motor

Contents

JYX C30/C40 48V Electric Scooter Motor User Manual

Models: C30 500W, C40 1000W

Batch/Serial Number: FQ241020

1. Introduction

This manual provides essential information for the safe and effective use of your JYX C30 500W or C40 1000W 48V electric scooter hub motor. This motor is designed for high-speed performance in 10-inch electric scooters, including models like Speedway and Dualtron, and E-Bikes. It features a 10x2.70-6.5 tubeless tire and Hall sensor technology.

2. Safety & Warnings

Please read all safety instructions before installation and use. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.

  • Do not use this product for purposes other than its intended use as an electric scooter motor.
  • Inspect the product thoroughly before each use. Do not use if any part is damaged.
  • Do not expose the motor to water or excessive moisture.
  • Ensure all electrical connections are secure and properly insulated to prevent short circuits.
  • Be aware of potential fire risks associated with electrical components. Ensure proper ventilation and avoid overheating.
  • Always disconnect power before performing any installation, maintenance, or inspection.

3. Product Overview

The JYX electric scooter motor is a robust hub motor unit integrated with a durable tubeless tire. It comes in two main variants: the C30 (500W) and the C40 (1000W), both operating at 48V.

3.1. Components

  • Motor Unit: Integrated hub motor with Hall sensors.
  • Tire: 10x2.70-6.5 tubeless tire, suitable for various terrains.
  • Motor Shaft: Designed for secure mounting to the scooter frame.
  • Wiring Harness: Includes phase wires and Hall sensor wires for connection to a compatible motor controller.

3.2. Features

  • Voltage: 48V DC.
  • Power Output: 500W (C30 model) or 1000W (C40 model).
  • High-Speed Engine: Designed for efficient and powerful propulsion.
  • Tubeless Tire: Enhances ride comfort and reduces puncture risks.
  • Hall Sensor Technology: Provides precise motor control and efficiency.
  • Magnet Strength: The 1000W version features a stronger magnet for increased power.
JYX C30/C40 48V 500/1000W Motor with cutaway view
Figure 1: JYX C30/C40 48V 500/1000W Motor with cutaway view of internal structure.

4. Setup and Installation

Proper installation is crucial for the motor's performance and safety. If you are unsure about any step, seek professional assistance.

4.1. Before First Use

Remove all protective films and packaging materials from the motor unit.

4.2. Physical Installation

  1. Prepare the Scooter: Ensure the scooter is powered off and stable. Remove the old wheel/motor assembly if replacing.
  2. Check Dimensions: Verify that the motor shaft dimensions match your scooter's fork or swingarm. The motor shaft has a length of 160mm, with an open gear width of 110mm, and a 30mm diameter section near the motor body.
  3. Mount the Motor: Carefully insert the motor shaft into the scooter's mounting points. Secure it using the provided nuts and washers, ensuring they are tightened to the manufacturer's specifications.
Motor shaft dimensions: 160mm length, 110mm open gear, 30mm diameter
Figure 2: Motor shaft dimensions and wiring details. Shaft length: 160mm, Open gear: 110mm, Motor line: About 90cm.

4.3. Electrical Wiring

Wiring must be done correctly to avoid damage to the motor or controller.

  1. Identify Wiring Types:
    • C30 500W Motor: Features outer wiring (wires exit the motor from the side).
    • C40 1000W Motor: Features internal wiring (wires exit the motor through the axle).
  2. Connect Phase Wires: Connect the three thick phase wires (typically green, yellow, blue) from the motor to the corresponding phase wires on your scooter's motor controller.
  3. Connect Hall Sensor Wires: Connect the five thinner Hall sensor wires (typically red, black, green, yellow, blue, sometimes white) from the motor to the corresponding Hall sensor input on your controller. Ensure positive (red) and negative (black) wires are correctly matched.
  4. Secure Connections: Use appropriate connectors and ensure all connections are tight and insulated to prevent short circuits or water ingress.
Comparison of C30 500W outer wiring and C40 1000W internal wiring
Figure 3: Wiring comparison: C30 500W (outer wiring) vs. C40 1000W (internal wiring).

5. Operating Instructions

The JYX motor operates in conjunction with your scooter's motor controller and battery system. There are no direct controls on the motor itself.

  • Once installed and wired correctly, the motor will respond to commands from your scooter's throttle and controller.
  • Ensure your scooter's battery is adequately charged before operation.
  • Always operate your scooter safely and in accordance with local regulations.

6. Maintenance

Regular maintenance will prolong the life and ensure the safe operation of your motor.

  • Regular Inspection: Periodically inspect the motor for any signs of physical damage, loose connections, or wear on the tire.
  • Keep Clean and Dry: Wipe down the motor with a dry or slightly damp cloth to remove dirt and debris. Avoid using harsh chemicals. Ensure the motor remains dry and free from moisture.
  • Wiring Check: Inspect the wiring harness for any fraying, cuts, or loose connections. Repair or replace damaged wiring immediately.
  • Tire Pressure: For optimal performance and tire longevity, regularly check and maintain the recommended tire pressure for the 10x2.70-6.5 tubeless tire.

7. Troubleshooting

If you encounter issues with your motor, refer to the following common troubleshooting steps:

  • Motor Not Spinning:
    • Check if the scooter's battery is charged.
    • Verify all wiring connections (phase and Hall sensor wires) between the motor and controller are secure.
    • Inspect the motor controller for any error codes or signs of malfunction.
  • Motor Making Unusual Noises:
    • Check for any physical obstructions around the wheel or motor.
    • Inspect the motor for any loose components or signs of internal damage.
  • Loss of Power or Intermittent Operation:
    • Ensure the battery is providing sufficient voltage.
    • Check all electrical connections for looseness or corrosion.
    • The motor controller might be faulty.

If problems persist after troubleshooting, contact customer support or a qualified technician.

8. Specifications

FeatureSpecification
Model NumbersC30, C40
Voltage48V
Power Output500W (C30), 1000W (C40)
Motor TypeHall High Speed Hub Motor
Tire Size10x2.70-6.5 Tubeless
Shaft Length160mm
Open Gear Width110mm
Motor Line LengthApprox. 90cm
OriginMainland China
Package Weight7.0 kg
Package Dimensions30cm x 30cm x 20cm

9. User Tips

  • Always double-check the specific model number (e.g., C30 500W or C40 1000W) and its wiring type (outer vs. internal) to ensure compatibility with your scooter's controller and frame.
  • When replacing a motor, compare the shaft length and open gear width of the new motor with your old one to ensure a proper fit.

10. Warranty & Support

This product must comply with all applicable safety and regulatory requirements in the market where it is sold.

Manufacturer

Taizhou Fengqi Motorcycle Parts Co., Ltd
No. 33-35 Shangxi Road, Luqiao Street, Luqiao District,
Taizhou, Zhejiang, CN(China) 318000

Email: 2239351145@qq.com
Phone: +86 13545581257

EU Authorized Representative

EU Consulten Srls
Via Varessina 55,
MILANO, MILANO, IT(Italy) 20156

Email: Eu-consultenSrls@hotmail.com
Phone: +39 3285832654

© 2023 JYX. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.