1. Introduction
The Gulikit SD02 Electromagnetic Joystick Module is designed as a high-precision replacement for the original joysticks in your Steam Deck. This module utilizes a patented electromagnetic design to eliminate joystick drift, providing a super smooth and durable gaming experience. It is compatible with both Type A and Type B joysticks found in Steam Deck models and offers a drop-in, no-soldering installation for core functionality.

2. Specifications
| Feature | Description |
|---|---|
| Brand Name | GuliKit |
| Model Number | SD02 |
| Compatible Brand/Model | Steam Deck |
| Accessories Type | Receiver/Transmitter/Transceiver (Joystick Module) |
| Joystick Type | Electromagnetic (Hall Effect) |
| Drift Prevention | Patented design for no stick drift |
| Installation | Drop-in, no soldering needed (for core functionality) |
| Power Consumption | Low power (50% less than old version SD01) |
| Origin | Mainland China |
| Package Includes | Electromagnetic Joystick Module (X2) |

3. Setup and Installation
Follow these instructions to replace the original joystick modules on your Steam Deck. The replacement procedure is the same for both left and right joysticks.
Important Safety Information:
- To avoid risk of damage, turn off your Steam Deck and discharge its battery to below 10% before starting the replacement work. Lithium-ion batteries can be very dangerous if accidentally punctured.
- Do not move other parts; only work on the joystick module during the replacement process.
- Follow ESD (Electrostatic Discharge) safety procedures during the replacement process.
Video Guide: Gulikit SD02 Installation Overview
Step 1: Select Mode (Type A or Type B)
Each Steam Deck is installed with one of two different models of thumbsticks, Type A or Type B. Although nearly identical, capacitive touch capability relies on the correct type to be installed.
To identify which replacement thumbsticks you need, navigate to Settings → System → Steam Deck Controller ID.
- If the Controller ID starts with "MEDA", that device uses a Type A thumbstick.
- If the Controller ID starts with "MHDA", that device uses a Type B thumbstick.
Turn the mode switch at the back of the SD02 module to the corresponding mode (A or B).

Step 2: Turn off Steam Deck
First, turn off your Steam Deck (ensure it's not just in sleep mode). Disconnect any cables.

Step 3: Remove the Screws on the Back Cover
- Remove the SD card first if your Steam Deck has one, before opening the back cover.
- Use a Phillips screwdriver to remove the eight screws on the back cover: four 9.5 mm screws and four 5.8 mm screws.
- Keep track of all the screws because you will need to install them back into your Steam Deck later.

Step 4: Open the Back Cover
- Use a pry tool and insert it into the gap between the back cover and the front cover along the grip.
- Gently pry up the back cover to release it from the locking points.
- Hold the front case with one hand, and pull the back cover up carefully with another hand to remove it completely from the device.

Step 5: Remove the Joystick Module Cable
- Use the tip of a pair of tweezers to lift up the small locking flap on the joystick cable's ZIF connector.
- Carefully take the cable out of the connector.
- Grip the cable by the blue pull tab, not by the cable itself, to avoid damage.

Step 6: Remove the Original Joystick Module
- Use a Phillips driver to remove the three 5.2 mm screws holding the original joystick module.
- Once the screws are removed, you can carefully remove the joystick module from your Steam Deck.

Step 7: Install Gulikit Joystick Module
- Although the stick cap is tightly attached to the joystick, there may be loosening of it during transportation. Before installation, you may press the stick cap down hard to avoid the joystick sticking by floating stick cap against the case. You can also do this without disassembling your console if you feel the stick is stuck during use.
- Place the Gulikit joystick module back into the joystick position of your Steam Deck.
- Install the screws back into place.
- Plug the cable into the ZIF connector and lock it.
- During this process, you need to hold the Steam Deck off of the work table surface so it isn't resting on the new joystick while you tighten down the screws.

Step 8: Reinstall the Back Cover and Screws
Now you can reassemble the back case to your Steam Deck and install the screws to finish the replacement work.

4. Operating Instructions
The Gulikit SD02 Electromagnetic Joystick Module is designed to provide precise and smooth control for your Steam Deck. Once installed and calibrated, it functions identically to the original joysticks but with enhanced durability and drift prevention.


5. Joystick Calibration
New joysticks require calibration to work as expected. To calibrate new thumbsticks, follow the calibration guide below:
- Steam Deck has its joysticks calibrated from the factory, and calibration values vary on each unit.
- Do not install the back case before joystick calibration.
- After Gulikit joysticks are installed, turn on your Steam Deck.
- Press the tiny switch on the board of the joystick module to get joysticks calibrated. Do not touch the joysticks during this process.
- Enter the joystick calibration interface on Steam Deck. Calibration is well finished if you see the spot return to the center position (0,0). Then you are good to screw up the shells and use your Steam Deck.
Follow the steps below in case the spot is off the center position (0,0):

Take the current spot position as the symmetrical point, move the joystick to the symmetrical position of the central point, next press the tiny calibration switch on the board, release the joystick, and calibration is successfully completed when you see the joystick returns to center position (0,0).
Note:
Because of the limitation of the physical structure, the ALPS joystick used by Steam Deck has an accuracy of ± 5 degrees in the center, while the Gulikit electromagnetic joystick has an accuracy of ± 3 degrees in the center. Therefore, under no dead zone mode, the joystick may not return to center exactly each time. This is normal and will not affect the experience in the game. Please use it with no worries.
6. Maintenance
- Keep the joystick modules clean and free from dust and debris.
- Avoid exposing the modules to extreme temperatures or moisture.
- Handle with care during installation and any subsequent maintenance to prevent damage to the delicate electronic components.
- The electromagnetic design inherently offers a longer work life compared to traditional potentiometer-based joysticks, reducing the need for frequent maintenance.

7. Troubleshooting
Joystick Drift or Incorrect Input
- Recalibration: Perform the joystick calibration steps outlined in Section 5. Ensure you do not touch the joysticks during the calibration process.
- Mode Selection: Verify that the A/B mode switch on the back of the joystick module is correctly set for your Steam Deck's controller ID (MEDA for Type A, MHDA for Type B).
- Connection Check: Ensure the ZIF connector cable is securely seated and locked. A loose connection can cause erratic behavior.
Capacitive Touch Not Working
- Soldering Requirement: The stick touch sensing function only works if the wire on the original stick cap of the Steam Deck is manually welded to the Gulikit joystick module. If you did not perform this step, the touch function will not be active.
- Mode Selection: Double-check the A/B mode switch as described above. Incorrect mode can affect touch functionality.
Joystick Feels Stuck or Not Smooth
- Stick Cap Check: As mentioned in Step 7 of installation, the stick cap might loosen during transport. Press the stick cap down hard to ensure it is fully seated and not causing friction against the case. This can be done without disassembling the console if the issue arises after installation.
8. User Tips
- Many users report these joysticks feel smoother than the originals and effectively eliminate the "hall effect" (drift).
- The SD02 version is designed for solderless installation for the main joystick function. However, if you desire capacitive touch functionality, manual soldering of a specific wire from the original stick cap to the Gulikit module is required.
- Always verify your Steam Deck's joystick type (Type A or Type B) via the Controller ID in settings before installation to ensure correct mode selection on the Gulikit module.
- After installation, remember to perform the calibration process. Some users find that even with the dead zone set to zero, the joysticks are perfectly centered after calibration.
9. Warranty and Support
For warranty information and technical support, please refer to the official GuliKit website or contact your retailer. Ensure you retain your proof of purchase for any warranty claims.