1. Introduction
This manual provides essential information for the installation, operation, and maintenance of your Dongcheng electric hammer piston, connecting rod, rubber ring, and pin assembly. These components are designed as replacement parts for various Dongcheng electric hammers and impact drills, ensuring optimal performance and longevity of your power tools. Please read this manual thoroughly before attempting any installation or maintenance.
2. Safety Information
Always prioritize safety when working with power tools and their components. Failure to follow these safety guidelines may result in injury or damage to equipment.
- Disconnect Power: Always ensure the electric hammer or impact drill is unplugged from the power source before attempting any installation, removal, or maintenance of parts.
- Wear Protective Gear: Use appropriate personal protective equipment (PPE), including safety glasses, gloves, and hearing protection.
- Use Correct Tools: Employ the correct tools for disassembly and assembly to prevent damage to components.
- Inspect Parts: Before installation, carefully inspect all new and existing parts for any defects, damage, or wear. Do not install damaged parts.
- Keep Work Area Clean: Maintain a clean and well-lit work area to prevent accidents.
- Professional Installation: If you are unsure about any step, seek assistance from a qualified technician.
3. Product Components
The product includes various piston, connecting rod, and rubber ring assemblies. The specific components you receive will depend on your selection. Below is a general overview of the parts and a visual reference.

For a visual demonstration of the components and their dimensions, please refer to the product video:
4. Specifications
The following table details the specifications for various available components. Please note that dimensions are approximate and may have slight manual measurement errors (1-3mm).
| Component Type | Key Dimensions | Weight (Approx.) | Material/Notes |
|---|---|---|---|
| 25mm Piston & Connecting Rod Set | Piston: H 24mm, Dia 27mm; Rod: L 70mm, 8mm hole | 40g | |
| 26mm Alloy Steel Connecting Rod | L 58mm, W 43mm; Holes: 8mm, 6mm | 36.2g | Alloy Steel |
| 26mm Aluminum Connecting Rod | L 60mm, W 43mm; Holes: 8mm, 6mm | 16.7g | Aluminum (with needle roller) |
| 27mm Piston | H 27mm, Dia 27mm; Pin hole: 6mm | 20g | |
| Hengyou 28T/32T Connecting Rod | L 69mm; Holes: 9.5mm, 8mm | 17.9g | Original Hengyou |
| Hengyou 28T Electric Hammer Piston | H 26mm, Dia 28mm; Pin hole: 8mm | 20g | Original Hengyou |
| Hengyou 32T Electric Hammer Piston | H 25mm, Dia 32mm; Pin hole: 8mm | 20g | Original Hengyou |
| 28mm Piston & 26mm Rubber Ring | Piston: H 27mm, Dia 27mm; Ring: Dia 26mm | 20.8g | |
| 26mm Piston Rubber Ring (5 pcs) | Outer Dia 25mm, Inner Dia 19mm, Thk 3mm | 5g | |
| 6830 Electric Hammer Connecting Rod | L 61mm; Holes: 10mm, 6mm | 20g |
General Product Information:
- DIY Supplies: Electrical
- Origin: Mainland China
- Certification: NONE
- High-concerned chemical: None
For detailed visual specifications of individual components, please refer to the images below:











5. Installation Instructions
These components are internal parts of an electric hammer or impact drill. Installation typically requires disassembly of the tool. It is recommended that installation be performed by individuals with experience in power tool repair.
- Tool Disassembly: Carefully disassemble your electric hammer or impact drill according to its specific service manual. Pay close attention to the order of components and any fasteners.
- Identify Worn Parts: Locate the existing piston, connecting rod, or rubber ring assembly that needs replacement.
- Remove Old Parts: Gently remove the worn or damaged components. Ensure no debris or fragments are left inside the tool.
- Install New Parts: Install the new piston, connecting rod, and rubber ring assembly. Ensure proper alignment and seating of all parts. For rubber rings, apply a small amount of appropriate lubricant (e.g., silicone grease) to aid installation and ensure a good seal.
- Reassembly: Reassemble the power tool in reverse order of disassembly. Ensure all screws and fasteners are tightened securely.
- Test Functionality: After reassembly, perform a brief test run of the tool without load to ensure all components are functioning correctly and there are no unusual noises or vibrations.
Note: Always refer to your specific power tool's service manual for detailed disassembly and reassembly procedures.
6. Operation
These components are internal replacement parts and do not directly affect the operational controls of your electric hammer or impact drill. Once correctly installed, the tool should operate as intended by its original manufacturer. Always follow the operating instructions provided with your specific power tool.
7. Maintenance
Proper maintenance of internal components ensures the longevity and efficiency of your power tool.
- Regular Inspection: Periodically inspect the piston, connecting rod, and rubber rings for signs of wear, cracking, or deformation. Replace parts as needed.
- Lubrication: Ensure adequate lubrication of moving parts, especially the piston and connecting rod, using the manufacturer-recommended grease or oil for your power tool. Rubber rings benefit from silicone-based lubricants to maintain flexibility and sealing properties.
- Cleanliness: Keep the internal mechanisms of your power tool free from dust, dirt, and debris, which can accelerate wear.
8. Troubleshooting
If your electric hammer or impact drill exhibits issues after replacing these components, consider the following:
- Loss of Impact/Hammering Function: This could indicate an issue with the piston or rubber ring seal. Recheck installation for proper seating and lubrication of the rubber rings. Ensure the piston is moving freely.
- Unusual Noises/Vibrations: May suggest improper installation of the connecting rod or piston, or a foreign object inside the mechanism. Disassemble and inspect for correct alignment and clear any obstructions.
- Tool Not Functioning: Double-check all electrical connections and ensure the tool was reassembled correctly. If the issue persists, consult a professional.
- Part Compatibility: Ensure the replacement parts match the specific model and type of your electric hammer or impact drill. Incorrect parts can lead to malfunction or damage.
9. User Tips
- Verify Dimensions: Before purchasing, always compare the dimensions of the replacement part with your original part to ensure perfect fit and compatibility. Use a caliper for accurate measurements.
- Lubricate Rubber Rings: A small amount of silicone grease on new rubber rings can significantly improve their sealing performance and ease of installation.
- Document Disassembly: Take photos or videos during disassembly to aid in correct reassembly, especially for complex power tools.
10. Warranty and Support
For any issues or questions regarding these replacement parts, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims. As these are replacement components, the warranty typically covers manufacturing defects of the part itself, not damage resulting from improper installation or misuse in the power tool.