HOBBYWING QUICRUN Fusion PRO 2-IN-1

Contents

HOBBYWING QUICRUN Fusion PRO 2-IN-1 Brushless Motor ESC Instruction Manual

Integrated Power System for 1/8 & 1/10 RC Crawlers

1. Introduction

The HOBBYWING QUICRUN Fusion PRO 2-IN-1 is an innovative integrated brushless motor and Electronic Speed Controller (ESC) system designed for high-performance 1/8 and 1/10 scale RC remote control model cars, particularly crawlers. This unit combines the motor and ESC into a single compact housing, simplifying wiring and installation while offering advanced features like FOC (Field-Oriented Control) for smooth, quiet, and efficient operation. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your QUICRUN Fusion PRO system.

HOBBYWING QUICRUN Fusion PRO 2-IN-1 Brushless Motor ESC in packaging with components
Figure 1: HOBBYWING QUICRUN Fusion PRO 2-IN-1 system and included components.

2. Setup and Installation

Careful installation is crucial for optimal performance and longevity of your Fusion PRO system. Ensure all connections are secure and correct before powering on.

2.1 Component Overview

The QUICRUN Fusion PRO integrates the motor and ESC. It features power input wires (typically with an XT60 connector), a signal wire for connection to your receiver, and a programming port.

Close-up of the HOBBYWING QUICRUN Fusion PRO 2-IN-1 motor and integrated ESC with wiring
Figure 2: Detailed view of the Fusion PRO unit, showing power and signal wiring.

2.2 Mounting the Unit

  1. Mount the Fusion PRO unit securely in your RC chassis using appropriate screws and mounting holes. Ensure it is positioned to allow for adequate airflow for cooling.
  2. Verify that the motor shaft aligns correctly with your vehicle's transmission/gearbox.
HOBBYWING QUICRUN Fusion PRO 2-IN-1 motor installed in an RC crawler chassis
Figure 3: Example installation of the Fusion PRO in an RC crawler chassis.

2.3 Wiring Connections

  1. Battery Connection: Connect your LiPo or NiMH battery pack to the XT60 power plug of the Fusion PRO. Ensure correct polarity (red to positive, black to negative).
  2. Receiver Connection: Plug the signal wire (usually a 3-pin connector) from the Fusion PRO into the throttle channel (CH2) of your RC receiver.
  3. Programming Port: The dedicated programming port is used for connecting an LED programming box (if applicable) to adjust parameters.

WARNING: Incorrect wiring can cause damage to the ESC, motor, battery, and other components. Always double-check connections before applying power.

3. Operating Instructions

Once installed and wired correctly, follow these steps to operate your RC vehicle with the Fusion PRO system:

  1. Transmitter Power On: Turn on your RC transmitter first. Ensure the throttle trim is at neutral.
  2. Vehicle Power On: Connect the battery to the Fusion PRO. The ESC will emit a series of tones indicating successful initialization and battery cell count.
  3. Throttle Calibration (if necessary): If the throttle response is incorrect, you may need to calibrate the ESC with your transmitter. Refer to the detailed HOBBYWING ESC manual for specific calibration procedures.
  4. Driving: You can now operate your RC vehicle. The FOC technology provides smooth low-speed control, which is ideal for crawling.
  5. Vehicle Power Off: Always disconnect the battery from the Fusion PRO first, then turn off your transmitter.

3.1 Parameter Programming

The Fusion PRO supports parameter programming via an LED programming box. This allows you to fine-tune settings such as running mode, drag brake force, low voltage cut-off, and more. Connect the LED programming box to the dedicated programming port on the Fusion PRO and follow the instructions provided with the programming box.

HOBBYWING QUICRUN Fusion PRO 2-IN-1 motor with an optional LED Program Card B
Figure 4: The Fusion PRO unit shown with an optional LED Program Card B for parameter adjustment.

4. Maintenance

Regular maintenance helps ensure the longevity and performance of your Fusion PRO system.

  • Cleaning: After each use, especially in dusty or wet conditions, clean the unit to remove dirt, mud, and debris. Use a soft brush or compressed air. Avoid using solvents that may damage plastic or electronic components.
  • Inspections: Periodically check all wires and connectors for signs of wear, fraying, or corrosion. Ensure all mounting screws are tight.
  • Motor Bearings: While brushless motors generally require less maintenance, check motor bearings for smooth operation. If they feel rough, they may need cleaning or replacement.
  • Storage: When not in use for extended periods, store the unit in a clean, dry place away from extreme temperatures. Disconnect the battery.

5. Troubleshooting

This section addresses common issues you might encounter. For more detailed troubleshooting, refer to the official HOBBYWING support resources.

Problem Possible Cause Solution
Motor not responding / No power
  • Battery not connected or discharged
  • Incorrect wiring
  • Transmitter not on or out of range
  • ESC in protection mode
  • Check battery connection and charge level
  • Verify all wiring connections (power, signal)
  • Turn on transmitter, check battery, ensure binding
  • Disconnect and reconnect battery to reset ESC
Motor stutters or runs roughly
  • Sensor wire issue (if applicable)
  • Motor or ESC overheating
  • Incorrect ESC settings
  • Check sensor wire connection
  • Allow unit to cool down, check gearing
  • Verify ESC parameters with programming box
Reduced power or short run time
  • Battery capacity low or damaged
  • Overheating
  • Incorrect gearing (too high)
  • Use fully charged, healthy battery
  • Check temperatures, adjust gearing
  • Reduce pinion size or increase spur size

6. Specifications

Key technical specifications for the HOBBYWING QUICRUN Fusion PRO 2-IN-1 Brushless Motor ESC system (2300KV variant):

Feature Specification
Brand HOBBYWING
Model QuicRun Fusion Pro 2-IN-1
Version Sensitive Brushless
Continuous/Peak Current 60A/200A
Battery Input 2-3S LiPo / 6-9 Cell NiMH
BEC Output Switch Mode: 6V/7.4V @ 6A
KV Rating 2300KV (Other variants: 1800KV, 1200KV)
Motor Outer Diameter 37mm
Motor Length 58mm
Motor Shaft Diameter 3.175mm
Motor Shaft Length 16mm
Number of Motor Poles 4
Power Plug XT60
Programming Method LED Programming Box
Weight 209g
Applicable Models 1/8, 1/10 RC Crawler
Material Metal
Recommended Age 14+ years

7. User Tips

  • Gearing: For crawling, experiment with different pinion/spur gear ratios to find the best balance of torque and speed for your specific vehicle and terrain. Lower gearing generally provides more torque and finer control.
  • Battery Choice: Always use high-quality LiPo or NiMH batteries that meet the voltage and discharge rate requirements of the Fusion PRO.
  • Temperature Monitoring: Regularly check the temperature of the motor and ESC during operation. If temperatures are consistently high, consider adjusting gearing, improving airflow, or reducing load.
  • Water Resistance: While the Fusion PRO is designed for RC crawlers which often encounter wet conditions, it's always best to avoid full submersion unless explicitly stated as fully waterproof. Dry the unit thoroughly after exposure to moisture.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the manufacturer, HOBBYWING, or the authorized seller from whom you purchased this product. Keep your proof of purchase for warranty claims.

Official HOBBYWING resources and support contact information can typically be found on their official website.

© 2024 HOBBYWING. All rights reserved. Information subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.